Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049329 AUDIO / VIDEO _0235782 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Radio Broadcast cannot be Received (Bad Reception)  


WIRING DIAGRAM

E278320E12
0.083,0.885 1.063,2.333 0.979,1.448 10 false Quarter Window Assembly (Window Glass Antenna Wire) 1.396,2.115 2.521,2.781 1.125,0.667 10 false Amplifier Antenna Assembly 3.521,2.302 4.458,2.958 0.938,0.656 10 false Antenna Cord Sub-assembly 5.823,2.448 7.052,3.042 1.229,0.594 10 false Radio and Display Receiver Assembly 5.823,2.26 6.135,2.458 0.313,0.198 10 false RA 5.49,1.375 5.729,1.583 0.24,0.208 10 false 5 5.49,1.063 5.729,1.271 0.24,0.208 10 false 3 6.063,1.115 6.74,1.323 0.677,0.208 10 false MAIN 6.073,1.563 6.75,1.771 0.677,0.208 10 false ANT+ 2.271,1.073 2.927,1.281 0.656,0.208 10 false 3*1, 8*2 2.271,1.385 3.021,1.604 0.75,0.219 10 false 1*1, 3*2 0.167,2.979 3.229,3.177 3.063,0.198 10 false *1: w/o SDARS System 0.177,3.354 3.083,3.552 2.906,0.198 10 false *2: w/ SDARS System

PROCEDURE

1.CHECK IF RADIO AUTO-SEARCH FUNCTIONS PROPERLY
a.

Check the radio automatic station search function by activating it.

OK:

Automatic station search function stops on a station.




OK

NG

2.CHECK OPTIONAL COMPONENTS
2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

OK:

Optional components are installed.


NOTICE:

Do not remove optional components without permission of the customer.




OK

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

NG

3.INSPECT QUARTER WINDOW ASSEMBLY (WINDOW GLASS ANTENNA WIRE)
3.INSPECT QUARTER WINDOW ASSEMBLY (WINDOW GLASS ANTENNA WIRE)
a.

Inspect the quarter window assembly (window glass antenna wire) (See page Audio / Visual / Telematics>AUDIO / VIDEO>WINDOW GLASS ANTENNA WIRE>REPAIR).



OK

4.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (ANTENNA)

NG

REPAIR QUARTER WINDOW ASSEMBLY (WINDOW GLASS ANTENNA WIRE)

4.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (ANTENNA)
a.
E276819

Remove the antenna connector from the radio and display receiver assembly.


b.

Turn the ignition switch to ACC with the radio and display receiver assembly connector connected.


c.

Turn on the radio and turn into AM mode.


d.

Place a screwdriver, thin wire or other metal object on the radio and display receiver assembly antenna jack and check that noise can be heard from the speakers.

OK:

Noise occurs.




OK

5.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

5.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E277921E01
1.063,0.781 1.281,0.781 1.281,0.781 1.531,1.042 true 2.333,0.635 2.083,0.635 2.083,0.635 1.833,0.885 true 2.354,1.583 2.104,1.583 2.104,1.583 1.833,1.271 true 0.677,0.698 1.208,0.885 0.531,0.188 10 false ANT+ 2.375,0.552 2.906,0.74 0.531,0.188 10 false 2 2.396,1.5 2.927,1.688 0.531,0.188 10 false 4

Disconnect the RA radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
5 (ANT+) - Body ground Ignition switch ACC, radio switch on and FM or AM selected 11 to 14 V




OK

6.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

6.CHECK ANTENNA CORD SUB-ASSEMBLY
a.

Disconnect the radio and display receiver assembly connector.

U154189E02
1.083,1.208 0.792,1.542 0.792,1.542 0.604,1.542 true 1.458,0.969 1.688,0.771 1.688,0.771 1.875,0.771 true 0.177,0.063 0.375,0.271 0.198,0.208 10 false *a 1.906,0.698 2.281,0.906 0.375,0.208 10 false ANT+ 0.229,1.469 0.604,1.677 0.375,0.208 10 false MAIN 4.948,0.052 5.396,0.26 0.448,0.208 10 false *b,*B 2.74,0.052 3.188,0.26 0.448,0.208 10 false *b,*A 0.302,0.865 0.677,1.073 0.375,0.208 10 false RA

Text in Illustration
*A w/o SDARS System *B w/ SDARS System
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of wire harness connector
(to Amplifier Antenna Assembly)


b.

Disconnect the antenna connector from the amplifier antenna assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o SDARS System:
Tester Connection Condition Specified Condition
RA-3 (MAIN) - 3 Always Below 1 Ω
RA-5 (ANT+) - 1 Always Below 1 Ω
RA-3 (MAIN) - Body ground Always 10 kΩ or higher
RA-5 (ANT+) - Body ground Always 10 kΩ or higher

w/ SDARS System:
Tester Connection Condition Specified Condition
RA-3 (MAIN) - 8 Always Below 1 Ω
RA-5 (ANT+) - 3 Always Below 1 Ω
RA-3 (MAIN) - Body ground Always 10 kΩ or higher
RA-5 (ANT+) - Body ground Always 10 kΩ or higher




OK

7.CHECK AMPLIFIER ANTENNA ASSEMBLY

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY

7.CHECK AMPLIFIER ANTENNA ASSEMBLY
a.

Replace the amplifier antenna assembly and check if radio broadcasts can be received normally.

OK:

Radio broadcasts can be received normally.




OK

END (AMPLIFIER ANTENNA ASSEMBLY IS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY