Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049329 AUDIO / VIDEO _0235782 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Radio Receiver Power Source Circuit  


DESCRIPTION

This circuit provides power to the radio and display receiver assembly.

WIRING DIAGRAM

E345033E01
1.01,0.344 2.844,0.542 1.833,0.198 10 false from Battery 0.615,0.802 2.448,1 1.833,0.198 10 false from IG No.1 Relay 0.802,1.302 2.635,1.5 1.833,0.198 10 false from ACC Relay 2.969,1 3.875,1.208 0.906,0.208 10 false ECU-IG No.1 5.708,0.344 6.042,0.583 0.333,0.24 10 false +B1 3.031,0.552 3.74,0.76 0.708,0.208 10 false RAD NO.1 5.417,0.156 5.583,0.333 0.167,0.177 10 false 4 5.375,0.365 5.656,0.552 0.281,0.188 10 false I58 5.406,0.625 5.573,0.802 0.167,0.177 10 false 1 5.417,1.115 5.583,1.292 0.167,0.177 10 false 3 5.417,1.552 5.583,1.729 0.167,0.177 10 false 7 5.375,0.813 5.656,1 0.281,0.188 10 false I61 5.365,1.313 5.646,1.5 0.281,0.188 10 false I58 5.375,1.75 5.656,1.938 0.281,0.188 10 false I58 5.74,0.802 6.073,1.042 0.333,0.24 10 false IG 5.719,1.292 6.167,1.531 0.448,0.24 10 false ACC1 5.729,1.76 6.177,2 0.448,0.24 10 false GND1 5.531,2.177 6.792,2.615 1.26,0.438 10 false Radio and Display Receiver Assembly 3.198,1.479 3.646,1.719 0.448,0.24 10 false ACC

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND GROUND)
a.
U154181E01
0.03,0.056 0.438,0.240 0.408,0.184 10 *a 1.544,0.376 1.903,0.560 0.359,0.184 10 I58 2.517,0.427 3.071,0.611 0.553,0.184 10 ACC1 2.788,0.845 3.172,1.029 0.384,0.184 10 +B1 2.008,1.134 2.228,0.51 2.228,0.51 2.494,0.51 false 2.012,1.974 2.492,2.158 0.480,0.184 10 GND1 1.548,1.639 1.723,2.057 1.723,2.057 1.989,2.057 false 2.266,1.13 2.513,0.932 2.513,0.932 2.779,0.932 false 1.596,2.433 1.955,2.617 0.359,0.184 10 I61 0.193,2.707 0.424,2.890 0.231,0.184 10 IG 0.777,3.411 0.597,2.794 0.597,2.794 0.451,2.794 false

Disconnect the radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I58-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I58-4 (+B1) - Body ground Always 11 to 14 V
I58-3 (ACC1) - Body ground Ignition switch ACC 11 to 14 V
I61-1 (IG) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR