Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049329 AUDIO / VIDEO _0235782 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends an external device sound signal to the radio and display receiver assembly through this circuit.

The sound signal that has been sent is amplified by the radio and display receiver assembly and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly or speakers.

WIRING DIAGRAM

E280106E09
5.698,0.417 6.146,0.583 0.448,0.167 10 false VAL+ 5.406,0.344 5.615,0.51 0.208,0.167 10 false 28 5.698,0.938 6.146,1.104 0.448,0.167 10 false VAR+ 5.406,0.854 5.615,1.021 0.208,0.167 10 false 26 5.698,1.438 6.146,1.604 0.448,0.167 10 false VA- 5.406,1.354 5.615,1.521 0.208,0.167 10 false 27 5.698,1.927 6.146,2.094 0.448,0.167 10 false AGND 5.406,1.865 5.615,2.031 0.208,0.167 10 false 11 5.698,2.448 6.146,2.615 0.448,0.167 10 false ADPG 2.625,2.104 3.5,2.271 0.875,0.167 10 false Shielded 4.052,2.094 4.927,2.26 0.875,0.167 10 false Shielded 1.25,0.396 1.583,0.563 0.333,0.167 10 false ALO 1.25,0.917 1.583,1.083 0.333,0.167 10 false ARO 1.135,1.438 1.583,1.604 0.448,0.167 10 false ASGN 1.135,1.927 1.583,2.094 0.448,0.167 10 false AGND 1.146,2.438 1.573,2.604 0.427,0.167 10 false AUXO 5.406,2.354 5.615,2.521 0.208,0.167 10 false 25 1.688,0.333 1.896,0.5 0.208,0.167 10 false 7 1.688,0.865 1.896,1.031 0.208,0.167 10 false 6 1.688,1.344 1.896,1.51 0.208,0.167 10 false 8 1.688,1.865 1.896,2.031 0.208,0.167 10 false 10 1.688,2.375 1.896,2.542 0.208,0.167 10 false 9 0.552,2.823 0.865,2.99 0.313,0.167 10 false I51 0.552,2.979 1.865,3.625 1.313,0.646 10 false No. 1 Stereo Jack Adapter Assembly 5.448,2.854 5.854,3.021 0.406,0.167 10 false I61 5.448,3.021 6.781,3.625 1.333,0.604 10 false Radio and Display Receiver Assembly

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the I61 radio and display receiver assembly connector.


b.

Disconnect the I51 No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I61-28 (VAL+) - I51-7 (ALO) Always Below 1 Ω
I61-26 (VAR+) - I51-6 (ARO) Always Below 1 Ω
I61-27 (VA-) - I51-8 (ASGN) Always Below 1 Ω
I61-11 (AGND) - I51-10 (AGND) Always Below 1 Ω
I61-25 (ADPG) - I51-9 (AUXO) Always Below 1 Ω
I61-28 (VAL+) - Body ground Always 10 kΩ or higher
I61-26 (VAR+) - Body ground Always 10 kΩ or higher
I61-27 (VA-) - Body ground Always 10 kΩ or higher
I61-11 (AGND) - Body ground Always 10 kΩ or higher
I61-25 (ADPG) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR