Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049329 AUDIO / VIDEO _0235782 AUDIO AND VISUAL SYSTEM C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  B15D5  Rear Seat Entertainment System Disconnected  


DESCRIPTION

The radio and display receiver assembly and television display assembly are connected by the AVC-LAN communication line.

When an AVC-LAN communication error occurs between the radio and display receiver assembly and television display assembly, this DTC will be stored.

DTC Code DTC Detection Condition Trouble Area
B15D5 When either condition below is met:
·

The television display assembly is/was not connected while the ignition switch is ON or ACC.

·

Communication between the master unit and the television display assembly is not possible when the engine is started.


·

AVC-LAN communication line

·

Television display assembly

·

Radio and display receiver assembly

·

Harness or connector



HINT:
·

Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.

·

The radio and display receiver assembly is the master unit.



WIRING DIAGRAM

E286157E03
5.604,0.396 5.854,0.573 0.25,0.177 10 false +B 5.406,0.313 5.51,0.49 0.104,0.177 10 false 1 2.781,0.552 3.521,0.885 0.74,0.333 10 false RAD NO.1 0.552,0.396 1.375,0.75 0.823,0.354 10 false from Battery 0.333,1.25 1.365,1.583 1.031,0.333 10 false from ACC Relay 2.938,1.427 3.313,1.781 0.375,0.354 10 false ACC 5.604,1.26 5.917,1.438 0.313,0.177 10 false ACC 5.406,1.167 5.51,1.344 0.104,0.177 10 false 2 5.604,2.167 6.01,2.344 0.406,0.177 10 false TX1+ 5.406,2.042 5.51,2.219 0.104,0.177 10 false 3 5.604,2.656 6.01,2.833 0.406,0.177 10 false TX1- 3.115,2.146 3.51,2.448 0.396,0.302 10 false TXM+ 3.156,2.646 3.521,2.823 0.365,0.177 10 false TXM- 2.458,2.99 2.823,3.167 0.365,0.177 10 false I57 1.135,4.198 3.292,4.594 2.156,0.396 10 false : AVC-LAN Communication Line 2.458,3.188 3.708,3.896 1.25,0.708 10 false Radio and Display Receiver Assembly 5.469,3.531 5.833,3.708 0.365,0.177 10 false U13 5.469,3.708 6.625,4.344 1.156,0.635 10 false Television Display Assembly 3.615,2.052 3.979,2.229 0.365,0.177 10 false 9 3.615,2.542 3.979,2.719 0.365,0.177 10 false 10 5.406,2.531 5.51,2.708 0.104,0.177 10 false 4 5.604,3.167 6.01,3.344 0.406,0.177 10 false GND 5.333,3.063 5.521,3.24 0.188,0.177 10 false 17

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses and relays for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK DTC

OK

NG

2.CHECK CONNECTOR CONNECTION CONDITION
2.CHECK CONNECTOR CONNECTION CONDITION
a.

Check that the television display assembly and radio and display receiver assembly connectors are connected properly.

OK:

The connectors are connected properly.




OK

3.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - BATTERY AND BODY GROUND)

NG

CONNECT CONNECTOR CORRECTLY

3.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - BATTERY AND BODY GROUND)
a.
U154138E02
1.063,1.125 0.813,0.75 0.813,0.75 0.667,0.75 true 1.281,1.323 1.448,1.677 1.448,1.677 1.594,1.677 true 1.167,1.125 1.333,0.563 1.333,0.563 1.469,0.563 true 0.198,0.094 0.354,0.271 0.156,0.177 10 false *a 1.625,1.594 1.948,1.771 0.323,0.177 10 false GND 0.438,0.688 0.625,0.865 0.188,0.177 10 false +B 1.521,0.479 2.094,0.656 0.573,0.177 10 false ACC 0.344,1.094 0.698,1.271 0.354,0.177 10 false U13

Disconnect the television display assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U13-17 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
U13-1 (+B) - Body ground Always 11 to 14 V
U13-2 (ACC) - Body ground Ignition switch ACC 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Television Display Assembly)


OK

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)
a.

Disconnect the I57 radio and display receiver assembly connector.


b.

Disconnect the U13 television display assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I57-9 (TXM+) - U13-3 (TX1+) Always Below 1 Ω
I57-10 (TXM-) - U13-4 (TX1-) Always Below 1 Ω
I57-9 (TXM+) - Body ground Always 10 kΩ or higher
I57-10 (TXM-) - Body ground Always 10 kΩ or higher




OK

5.CHECK TELEVISION DISPLAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TELEVISION DISPLAY ASSEMBLY
a.

Replace the television display assembly with a known good one (See page Audio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL).



c.

Check for DTCs (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are not output.




OK

END (TELEVISION DISPLAY ASSEMBLY IS DEFECTIVE)

NG

REPLACE RADIO AND RECEIVER ASSEMBLY