Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049330 NAVIGATION / MULTI INFO DISPLAY _0235785 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Reverse Signal Circuit  


DESCRIPTION

The navigation receiver assembly receives a reverse signal from the park/neutral position switch assembly.

WIRING DIAGRAM

E282599E02
2.798,1.214 4.576,1.635 1.778,0.421 10 Park/Neutral Position Switch Assembly 5.495,1.303 5.922,1.486 0.427,0.184 10 I53 5.495,1.462 6.828,1.807 1.333,0.345 10 Navigation Receiver Assembly 2.798,1.059 3.124,1.243 0.327,0.184 10 D21 0.582,0.732 2.016,1.081 1.434,0.349 10 from LH-IG Fuse 3.91,0.617 4.174,0.800 0.264,0.184 10 RL 3.282,0.628 3.546,0.811 0.264,0.184 10 RB 3.115,0.619 3.379,0.803 0.264,0.184 10 2 5.65,0.728 5.983,0.912 0.334,0.184 10 REV 5.331,0.625 5.571,0.809 0.240,0.184 10 2 4.189,0.625 4.315,0.809 0.125,0.184 10 1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E285964

Enter the "Vehicle Signal Check Mode" screen. [Refer to check Vehicle Signal in Operation Check (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK)].


b.

Check that the display changes between ON and OFF according to the shift lever position.

OK:
Shift Lever Position Display
R ON
Except R OFF


HINT:

This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK NAVIGATION RECEIVER ASSEMBLY
2.CHECK NAVIGATION RECEIVER ASSEMBLY
U153955E01
0.067,0.058 0.309,0.243 0.242,0.186 10 *a 1.598,0.502 1.962,0.692 0.364,0.191 10 I53 0.063,0.733 0.392,0.904 0.330,0.171 10 REV 0.944,1.363 0.643,0.82 0.643,0.82 0.459,0.82 false

a.

Disconnect the navigation receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I53-2 (REV) - Body ground Ignition switch ON, shift lever in R 7.5 to 14 V
I53-2 (REV) - Body ground Ignition switch ON, shift lever not in R Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Navigation Receiver Assembly)



OK

NG

3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the I53 navigation receiver assembly connector.


b.

Disconnect the D21 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I53-2 (REV) - D21-1 (RL) Always Below 1 Ω
I53-2 (REV) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)
a.
U154161E01
2.771,0.446 3.063,0.657 0.291,0.212 10 RB 1.554,0.246 1.846,0.458 0.291,0.212 10 D21 0.046,0.033 0.337,0.245 0.291,0.212 10 *a 1.856,1.025 2.522,0.528 2.522,0.528 2.739,0.528 false

Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D21-2 (RB) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Park/neutral Position Switch Assembly)

Result
Result Proceed to
OK (for AB60E) A
OK (for AB60F) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR