Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049330 NAVIGATION / MULTI INFO DISPLAY _0235785 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Radio Broadcast cannot be Received or Poor Reception  


WIRING DIAGRAM

E278320E11
0.188,1.219 1.208,1.906 1.021,0.688 10 false Window Glass Antenna Wire 1.396,2.115 2.521,2.448 1.125,0.333 10 false Amplifier Antenna Assembly 3.521,2.302 4.438,2.646 0.917,0.344 10 false Antenna Cord Sub-assembly 6,2.427 6.938,2.771 0.938,0.344 10 false Navigation Receiver Assembly 5.99,2.26 6.302,2.458 0.313,0.198 10 false RA 5.49,1.375 5.729,1.583 0.24,0.208 10 false 5 5.49,1.063 5.729,1.271 0.24,0.208 10 false 3 6.073,1.49 6.75,1.698 0.677,0.208 10 false ANT+ 2.271,1.073 2.844,1.26 0.573,0.188 10 false 3*1, 8*2 2.271,1.385 2.823,1.594 0.552,0.208 10 false 1*1, 3*2 0.375,3.052 3.438,3.25 3.063,0.198 10 false *1: w/o SDARS System 0.385,3.427 3.292,3.625 2.906,0.198 10 false *2: w/ SDARS System

PROCEDURE

1.CHECK IF RADIO AUTO-SEARCH FUNCTIONS PROPERLY
a.

Check the radio automatic station search function by activating it.

OK:

Automatic station search function stops on a station.




OK

NG

2.CHECK OPTIONAL COMPONENTS
2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

OK:

Optional components are installed.


NOTICE:

Do not remove optional components without permission of the customer.




OK

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

NG

3.CHECK WINDOW GLASS ANTENNA WIRE
3.CHECK WINDOW GLASS ANTENNA WIRE
a.
E111994E22
1.146,1.865 1.021,1.615 false 2.281,1.667 2.146,1.396 false 0.688,1.135 0.635,0.938 false 0.542,0.75 0.854,0.948 0.313,0.198 10 false *a 1.146,1.906 1.458,2.104 0.313,0.198 10 false *b 2.219,1.688 2.531,1.885 0.313,0.198 10 false *c

Check for continuity in the window glass antenna wire.

HINT:

Check for continuity at the center of each antenna wire as shown in the illustration.


NOTICE:

When cleaning the glass, wipe it in the direction of the wire with a soft dry cloth. Take care not to damage the wire. Do not use detergents or glass cleaners with abrasive ingredients. When measuring resistance, wrap a piece of tin foil around the tip of each probe and press the foil against the wire with your finger as shown in the illustration.


OK:

There is continuity in the window glass antenna wire.


Text in Illustration
*a Tester Probe
*b Antenna Wire
*c Tin Foil



OK

4.CHECK NAVIGATION RECEIVER ASSEMBLY (ANTENNA)

NG

4.CHECK NAVIGATION RECEIVER ASSEMBLY (ANTENNA)
a.
E276819

Remove the antenna connector from the navigation receiver assembly.


b.

Turn the ignition switch to ACC with the navigation receiver assembly connector connected.


c.

Turn on the radio and turn into AM mode.


d.

Place a screwdriver, thin wire or other metal object on the navigation receiver assembly antenna jack and check that noise can be heard from the speakers.

OK:

Noise occurs.




OK

5.INSPECT NAVIGATION RECEIVER ASSEMBLY

NG

5.INSPECT NAVIGATION RECEIVER ASSEMBLY
a.
E277921E01
1.063,0.781 1.281,0.781 1.281,0.781 1.531,1.042 true 2.333,0.635 2.083,0.635 2.083,0.635 1.833,0.885 true 2.354,1.583 2.104,1.583 2.104,1.583 1.833,1.271 true 0.677,0.698 1.208,0.885 0.531,0.188 10 false ANT+ 2.375,0.552 2.906,0.74 0.531,0.188 10 false 2 2.396,1.5 2.927,1.688 0.531,0.188 10 false 4

Disconnect the RA navigation receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
5 (ANT+) - Body ground Ignition switch ACC, radio switch on and FM or AM selected 11 to 14 V




OK

6.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

6.CHECK ANTENNA CORD SUB-ASSEMBLY
a.

Disconnect the navigation receiver assembly connector.

U154189E02
1.083,1.208 0.792,1.542 0.792,1.542 0.604,1.542 true 1.458,0.969 1.688,0.771 1.688,0.771 1.875,0.771 true 0.177,0.063 0.375,0.271 0.198,0.208 10 false *a 1.906,0.698 2.281,0.906 0.375,0.208 10 false ANT+ 0.229,1.469 0.604,1.677 0.375,0.208 10 false MAIN 4.948,0.052 5.396,0.26 0.448,0.208 10 false *b,*B 2.74,0.052 3.188,0.26 0.448,0.208 10 false *b,*A 0.302,0.865 0.677,1.073 0.375,0.208 10 false RA

Text in Illustration
*A w/o SDARS System *B w/ SDARS System
*a Front view of wire harness connector
(to Navigation Receiver Assembly)
*b Front view of wire harness connector
(to Amplifier Antenna Assembly)


b.

Disconnect the antenna connector from the amplifier antenna assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
RA-3 (MAIN) - 3*1 Always Below 1 Ω
RA-5 (ANT+) - 1*1 Always Below 1 Ω
RA-3 (MAIN) - 8*2 Always Below 1 Ω
RA-5 (ANT+) - 3*2 Always Below 1 Ω
RA-3 (MAIN) - Body ground Always 10 kΩ or higher
RA-5 (ANT+) - Body ground Always 10 kΩ or higher


*1: w/o SDARS System

*2: w/ SDARS System




OK

7.CHECK AMPLIFIER ANTENNA ASSEMBLY

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY

7.CHECK AMPLIFIER ANTENNA ASSEMBLY
a.

Replace the amplifier antenna assembly.


b.

Check if radio broadcasts can be received normally.

OK:

Radio broadcasts can be received normally.




OK

END (AMPLIFIER ANTENNA ASSEMBLY IS DEFECTIVE)

NG