Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049330 NAVIGATION / MULTI INFO DISPLAY _0235785 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Mute Signal Circuit between Navigation Receiver Assembly and Stereo Component Amplifier  


DESCRIPTION

This circuit sends a signal to the stereo component amplifier assembly to mute noise. Because of that, the noise produced by changing the sound source ceases.

If there is an open in the circuit, noise can be heard from the speakers when changing the sound source.

If there is a short in the circuit, even though the stereo component amplifier assembly is functioning normally, no sound or only an extremely faint sound can be heard.

WIRING DIAGRAM

E282597E03
1.229,0.885 2,1.031 0.771,0.146 10 false MUTE 0.677,1.802 1.448,1.948 0.771,0.146 10 false I17 0.688,1.948 2.188,2.594 1.5,0.646 10 false Stereo Component Amplifier Assembly 5.333,1.802 6.104,1.948 0.771,0.146 10 false I53 5.344,1.938 6.646,2.552 1.302,0.615 10 false Navigation Receiver Assembly 1.76,0.781 1.906,0.927 0.146,0.146 10 false 1 5.594,0.885 6.365,1.031 0.771,0.146 10 false MUT1 5.323,0.792 5.552,0.938 0.229,0.146 10 false 16

PROCEDURE

1.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY
a.
U154147E02
2.396,1.885 2.865,2.385 true 0.208,0.167 0.365,0.333 0.156,0.167 10 false *a 1.625,0.906 1.885,1.073 0.26,0.167 10 false I17 2.698,2.417 3.125,2.583 0.427,0.167 10 false MUTE

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I17-1 (MUTE) - Body ground Ignition switch ACC, audio system playing
→ Changing modes
Above 3.5 V
→ Below 1 V


Text in Illustration
*a Component with harness connected
(Stereo Component Amplifier Assembly)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the I53 navigation receiver assembly connector.


b.

Disconnect the I17 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I53-16 (MUT1) - I17-1 (MUTE) Always Below 1 Ω
I53-16 (MUT1) - Body ground Always 10 kΩ or higher




OK

3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)
a.

Disconnect the navigation receiver assembly connector.


b.
U154146E01
1.624,0.801 1.860,0.957 0.237,0.156 10 I53 0.181,0.157 0.336,0.312 0.154,0.156 10 *a 0.697,2.597 1.093,2.753 0.396,0.156 10 MUT1 1.069,2.2 0.946,2.583 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I53-16 (MUT1) - Body ground Ignition switch ACC, audio system is playing Above 3.5 V


Text in Illustration
*a Front view of wire harness connector
(to Navigation Receiver Assembly)



OK

NG

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY