Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049330 NAVIGATION / MULTI INFO DISPLAY _0235785 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B15D3  Stereo Component Amplifier Disconnected  


DESCRIPTION

The navigation receiver assembly and stereo component amplifier assembly are connected via AVC-LAN communication.

When an AVC-LAN communication error occurs between the navigation receiver assembly and stereo component amplifier assembly, this DTC will be stored.

DTC Code DTC Detection Condition Trouble Area
B15D3 When either condition below is met:
·

Stereo component amplifier assembly is/was not connected while the ignition switch is ACC or ON.

·

Communication between the master unit and the stereo component amplifier assembly is not possible when the engine is started.


·

Stereo component amplifier assembly

·

Navigation receiver assembly

·

Harness or connector



HINT:
·

Even if no fault is present, this DTC may be stored depending on the battery condition.

·

The navigation receiver assembly is the master unit.



WIRING DIAGRAM

E282588E03
2.979,0.781 3.885,0.969 0.906,0.188 10 false AMP 5.354,0.427 5.542,0.615 0.188,0.188 10 false 1 5.365,0.844 5.583,1.031 0.219,0.188 10 false 3 5.323,1.229 5.677,1.417 0.354,0.188 10 false 12 5.354,2.021 5.542,2.208 0.188,0.188 10 false 8 5.375,2.417 5.563,2.604 0.188,0.188 10 false 7 5.375,2.813 5.563,3 0.188,0.188 10 false 2 5.302,3.396 5.594,3.583 0.292,0.188 10 false I16 5.302,1.021 5.594,1.208 0.292,0.188 10 false I16 5.302,0.625 5.594,0.813 0.292,0.188 10 false I16 5.667,0.594 6.167,0.781 0.5,0.188 10 false +B 5.667,1.01 6.167,1.198 0.5,0.188 10 false +B2 5.667,1.406 6.167,1.594 0.5,0.188 10 false ACC 5.667,2.167 6.167,2.354 0.5,0.188 10 false TX+ 5.667,2.604 6.167,2.792 0.5,0.188 10 false TX- 5.667,2.99 6.167,3.177 0.5,0.188 10 false GND 5.646,3.396 6.146,3.583 0.5,0.188 10 false GND2 5.302,3 5.594,3.188 0.292,0.188 10 false I16 5.302,2.604 5.594,2.792 0.292,0.188 10 false I17 5.302,2.208 5.594,2.396 0.292,0.188 10 false I17 5.302,1.417 5.594,1.604 0.292,0.188 10 false I17 5.375,3.208 5.667,3.396 0.292,0.188 10 false 6 3.656,2.458 4.104,2.646 0.448,0.188 10 false 8 3.656,2.094 4.104,2.281 0.448,0.188 10 false 7 3.219,2.188 3.667,2.375 0.448,0.188 10 false TX1+ 3.271,2.625 3.719,2.813 0.448,0.188 10 false TX1- 2.5,3.156 3.844,3.531 1.344,0.375 10 false Navigation Receiver Assembly 5.167,3.875 7,4.573 1.833,0.698 10 false Stereo Component Amplifier Assembly 2.5,2.979 2.948,3.167 0.448,0.188 10 false I53 1.24,4.208 4.719,4.49 3.479,0.281 10 false : AVC-LAN Communication Line 3,1.552 3.906,1.74 0.906,0.188 10 false ACC 0.323,1.396 1.573,1.583 1.25,0.188 10 false from ACC Relay 0.573,0.615 1.823,0.802 1.25,0.188 10 false from Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK FOR DTC
a.

If DTC B15C3 is output, perform the troubleshooting of DTC B15C3 first.

Result
Result Proceed to
DTC B15C3 is not output. A
DTC B15C3 is output. B



A

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B

HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

·

This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.





A

3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

4.CHECK FOR DTC
3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.




NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC

b.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

END (COMMUNICATION MALFUNCTION DUE TO NOISE)

NG

5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)
5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)
a.
U154156E01
0.179,0.187 0.437,0.381 0.258,0.194 10 *a 1.545,1.832 1.873,1.994 0.328,0.162 10 I17 1.545,0.371 1.873,0.533 0.328,0.162 10 I16 0.757,0.552 1.247,0.732 0.489,0.179 10 +B 0.627,0.862 1.116,1.041 0.489,0.179 10 +B2 0.964,0.944 1.046,0.944 1.046,0.944 1.353,1.208 false 1.041,0.649 1.123,0.649 1.123,0.649 1.353,0.985 false 2.344,0.561 2.834,0.740 0.489,0.179 10 GND 2.655,2.071 3.144,2.250 0.489,0.179 10 ACC 2.613,2.153 2.531,2.153 2.531,2.153 2.388,2.62 false 2.409,0.862 2.898,1.041 0.489,0.179 10 GND2 2.367,0.944 2.284,0.944 2.284,0.944 1.978,1.208 false 2.289,0.649 2.207,0.649 2.207,0.649 1.978,0.985 false

Disconnect the stereo component amplifier assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I16-2 (GND) - Body ground Always Below 1 Ω
I16-6 (GND2) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I16-1 (+B) - I16-2 (GND) Always 11 to 14 V
I16-3 (+B2) - I16-2 (GND) Always 11 to 14 V
I17-12 (ACC) - I16-2 (GND) Ignition switch ACC 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Stereo Component Amplifier Assembly)


OK

6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the I53 navigation receiver assembly connector.


b.

Disconnect the I17 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I53-7 (TX1+) - I17-8 (TX+) Always Below 1 Ω
I53-8 (TX1-) - I17-7 (TX-) Always Below 1 Ω
I53-7 (TX1+) - Body ground Always 10 kΩ or higher
I53-8 (TX1-) - Body ground Always 10 kΩ or higher




OK

7.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Replace the stereo component amplifier assembly with a known good one (See page Audio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL).



c.

Recheck for DTCs and check if the same DTC is output again.

OK:

No DTCs are output.




OK

END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE)

NG