Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049330 NAVIGATION / MULTI INFO DISPLAY _0235785 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B15D5  Rear Seat Entertainment System Disconnected  


DESCRIPTION

The navigation receiver assembly and television display assembly are connected by the AVC-LAN communication line.

When an AVC-LAN communication error occurs between the navigation receiver assembly and television display assembly, these DTCs will be stored.

DTC Code DTC Detection Condition Trouble Area
B15D5 A device that is listed in the AVC-LAN network connected device record of the master unit is missing.
·

Television display assembly power source circuit

·

AVC-LAN circuit between stereo component amplifier assembly and television display assembly

·

AVC-LAN circuit between television display assembly and navigation receiver assembly

·

Television display assembly

·

Navigation receiver assembly



HINT:

For the AVC-LAN network, the navigation receiver assembly is the master unit.


WIRING DIAGRAM

E283431E02
1.917,1.083 2.229,1.25 0.313,0.167 10 false ACC 1.729,0.635 2.51,0.802 0.781,0.167 10 false RAD NO. 1 0.198,0.917 1.49,1.104 1.292,0.188 10 false from ACC Relay 3.063,0.417 3.26,0.563 0.198,0.146 10 false 1 3.052,0.844 3.208,0.99 0.156,0.146 10 false 2 4.24,0.406 4.448,0.552 0.208,0.146 10 false 17 4.26,1.573 4.417,1.719 0.156,0.146 10 false 3 4.26,2 4.417,2.146 0.156,0.146 10 false 4 3.229,0.49 3.5,0.635 0.271,0.146 10 false +B 3.229,0.948 3.74,1.094 0.51,0.146 10 false ACC 3.854,0.479 4.198,0.635 0.344,0.156 10 false GND 5.698,1.635 6.313,1.823 0.615,0.188 10 false TXM+ 5.698,2.063 6.313,2.25 0.615,0.188 10 false TXM- 3.833,1.656 4.531,1.844 0.698,0.188 10 false TX1+ 3.833,2.063 4.531,2.25 0.698,0.188 10 false TX1- 3.167,2.521 3.865,2.708 0.698,0.188 10 false U13 5.542,1.552 5.677,1.75 0.135,0.198 10 false 9 5.479,1.979 5.729,2.177 0.25,0.198 10 false 10 5.698,2.521 5.969,2.688 0.271,0.167 10 false I25 5.698,2.667 6.969,3.271 1.271,0.604 10 false Navigation Receiver Assembly 3.156,2.677 4.635,3.313 1.479,0.635 10 false Television Display Assembly 0.427,0.49 1.229,0.677 0.802,0.188 10 false from Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check for optional components.

i.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B

HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

·

This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.






A

2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

3.CHECK FOR DTC
2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.




NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC

b.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

END (COMMUNICATION MALFUNCTION DUE TO NOISE)

NG

4.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - POWER SOURCE AND BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - POWER SOURCE AND BODY GROUND)
a.
U154188E02
1.052,1.219 0.823,1.802 true 0.927,1.177 0.542,1.385 true 1.188,1.354 1.385,1.74 true 0.313,1.323 0.542,1.49 0.229,0.167 10 false +B 0.635,1.833 0.948,2 0.313,0.167 10 false ACC 1.323,1.771 1.667,1.938 0.344,0.167 10 false GND 0.052,0.073 0.271,0.24 0.219,0.167 10 false *a 1.573,0.396 1.885,0.542 0.313,0.146 10 false U13

Disconnect the television display assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U13-17 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
U13-1 (+B) - U13-17 (GND) Always 11 to 14 V
U13-2 (ACC) - U13-17 (GND) Ignition switch ACC 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Television Display Assembly)


OK

5.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)
a.

Disconnect the U13 television display assembly connector.


b.

Disconnect the I25 navigation receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U13-3 (TX1+) - I25-9 (TXM+) Always Below 1 Ω
U13-4 (TX1-) - I25-10 (TXM-) Always Below 1 Ω
U13-3 (TX1+) - Body ground Always 10 kΩ or higher
U13-4 (TX1-) - Body ground Always 10 kΩ or higher




OK

6.REPLACE TELEVISION DISPLAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE TELEVISION DISPLAY ASSEMBLY
a.

Replace the television display assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>TELEVISION DISPLAY>REMOVAL).



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC

b.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

END (TELEVISION DISPLAY ASSEMBLY IS DEFECTIVE)

NG