Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › INTUITIVE PARKING ASSIST SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049331 PARK ASSIST / MONITORING _0235786 INTUITIVE PARKING ASSIST SYSTEM J

PARK ASSIST / MONITORING  INTUITIVE PARKING ASSIST SYSTEM  Park / Neutral Position Switch Circuit  


DESCRIPTION

This circuit sends the park/neutral position switch assembly signals to the clearance warning ECU assembly.

WIRING DIAGRAM

E280658E03
5.354,2.302 5.833,2.458 0.479,0.156 10 false H128 5.51,1.76 5.99,1.917 0.479,0.156 10 false RL 5.51,0.938 5.99,1.094 0.479,0.156 10 false PL 5.24,1.667 5.469,1.823 0.229,0.156 10 false 21 3.208,1.323 3.688,1.479 0.479,0.156 10 false RB 3.031,1.219 3.177,1.375 0.146,0.156 10 false 2 5.302,0.833 5.5,0.99 0.198,0.156 10 false 6 4.052,1.781 4.302,1.938 0.25,0.156 10 false RL 4.052,0.948 4.302,1.104 0.25,0.156 10 false PL 4.344,1.667 4.573,1.823 0.229,0.156 10 false 1 4.344,0.833 4.573,0.99 0.229,0.156 10 false 6 5.344,2.479 6.635,2.833 1.292,0.354 10 false Clearance Warning ECU Assembly 3.063,2.302 3.542,2.458 0.479,0.156 10 false D21 2.135,1.49 2.958,1.646 0.823,0.156 10 false LH-IG 0.333,1.323 1.719,1.552 1.385,0.229 10 false from IG No.1 Relay 3.063,2.479 4.5,2.833 1.438,0.354 10 false Park/Neutral Position Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK CLEARANCE WARNING ECU ASSEMBLY
a.
U154162E02
2.156,0.958 2.604,0.385 2.604,0.385 2.792,0.385 true 2.104,1.188 2.552,1.781 2.552,1.781 2.74,1.781 true 1.552,0.219 1.969,0.385 0.417,0.167 10 false H128 0.083,0.052 0.427,0.219 0.344,0.167 10 false *a 2.833,0.302 3.177,0.469 0.344,0.167 10 false PL 2.781,1.698 3.125,1.865 0.344,0.167 10 false RL

Disconnect the clearance warning ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H128-6 (PL) - Body ground Ignition switch ON, shift lever in P 11 to 14 V
Ignition switch ON, shift lever not in P Below 1 V
H128-21 (RL) - Body ground Ignition switch ON, shift lever in R 11 to 14 V
Ignition switch ON, shift lever not in R Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - CLEARANCE WARNING ECU ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - CLEARANCE WARNING ECU ASSEMBLY)
a.

Disconnect the D21 park/neutral position switch assembly connector.


b.

Disconnect the H128 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D21-6 (PL) - H128-6 (PL) Always Below 1 Ω
D21-1 (RL) - H128-21 (RL) Always Below 1 Ω
D21-6 (PL) or H128-6 (PL) - Body ground Always 10 kΩ or higher
D21-1 (RL) or H128-21 (RL) - Body ground Always 10 kΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)
a.
U153984E02
1.833,1.302 2.458,0.833 2.458,0.833 2.708,0.833 true 0.094,0.052 0.354,0.26 0.26,0.208 10 false *a 1.604,0.542 1.885,0.708 0.281,0.167 10 false D21 2.75,0.771 2.99,0.917 0.24,0.146 10 false RB

Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D21-2 (RB) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)

Result
Result Proceed to
OK (for AB60E) A
OK (for AB60F) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR