PARK ASSIST / MONITORING
INTUITIVE PARKING ASSIST SYSTEM
- PRECAUTION
- PARTS LOCATION
- SYSTEM DIAGRAM
- SYSTEM DESCRIPTION
- HOW TO PROCEED WITH TROUBLESHOOTING
- OPERATION CHECK
- PROBLEM SYMPTOMS TABLE
- TERMINALS OF ECU
- Park / Neutral Position Switch Circuit
- Vehicle Speed Signal Circuit
- Taillight Relay Circuit
- Back Sonar Sensor LH Circuit
- Back Sonar Sensor RH Circuit
- Front Clearance Sonar Sensor LH Circuit
- Front Clearance Sonar Sensor RH Circuit
- Rear Clearance Sonar Sensor LH Circuit
- Rear Clearance Sonar Sensor RH Circuit
- Clearance Warning Buzzer Circuit
- Clearance Warning ECU Power Source Circuit
- Indicator Circuit
REAR VIEW MONITOR SYSTEM(for Radio and Display Type)
- PRECAUTION
- PARTS LOCATION
- SYSTEM DIAGRAM
- SYSTEM DESCRIPTION
- HOW TO PROCEED WITH TROUBLESHOOTING
- PROBLEM SYMPTOMS TABLE
- TERMINALS OF ECU
- DTC CHECK / CLEAR
- DIAGNOSTIC TROUBLE CODE CHART
- C1622 Open or Short Circuit in rear television camera signal
- Screen Flicker or Color Distortion
- Reverse Signal Circuit
- Image from Camera for Rear View Monitor is Abnormal
REAR VIEW MONITOR SYSTEM(for Navigation Receiver Type)
- PRECAUTION
- PARTS LOCATION
- SYSTEM DIAGRAM
- SYSTEM DESCRIPTION
- HOW TO PROCEED WITH TROUBLESHOOTING
- PROBLEM SYMPTOMS TABLE
- TERMINALS OF ECU
- DTC CHECK / CLEAR
- DIAGNOSTIC TROUBLE CODE CHART
- C1622 Open or Short Circuit in television camera signal
- Screen Flicker or Color Distortion
- Reverse Signal Circuit
- Image from Camera for Rear View Monitor is Abnormal
BLIND SPOT MONITOR SYSTEM
- PRECAUTION2015.08–2016.10from 2016.10
- PARTS LOCATION
- SYSTEM DIAGRAM
- SYSTEM DESCRIPTION
- HOW TO PROCEED WITH TROUBLESHOOTING
- OPERATION CHECK2015.08–2016.10from 2016.10
- PROBLEM SYMPTOMS TABLE
- TERMINALS OF ECU
- DIAGNOSIS SYSTEM
- DTC CHECK / CLEAR
- FREEZE FRAME DATA
- DATA LIST / ACTIVE TEST
- DIAGNOSTIC TROUBLE CODE CHART
- U0233 The blind spot monitor sensor LH cannot receive signals from the blind spot monitor sensor RH.
- U1331 Destination information of the main body ECU and blind spot monitor sensor do not match.
- U0232 The blind spot monitor sensor RH cannot receive signals from the blind spot monitor sensor LH.
- U0100, U0126, U0129, U0142
- C1ABC A beam axis inspection has not been performed.
- C1ABB A beam axis inspection has not been performed.
- C1ABA There is an open in the ground circuit (Terminal No. 3) of the blind spot monitor sensor LH for a specified...
- C1AB8 The blind spot monitor sensor cannot communicate with the main body ECU.
- C1AB7 The blind spot monitor sensor LH (slave) detects an internal malfunction.
- C1AB6 The blind spot monitor sensor RH (master) detects an internal malfunction.
- C1AB5 With the blind spot monitor main switch assembly (warning canceling switch assembly) on, the current flowing...
- C1AB4 With the blind spot monitor main switch assembly (warning canceling switch assembly) on, the current flowing...
- C1AB3 With the blind spot monitor main switch assembly (warning canceling switch assembly) on, the voltage output...
- C1AB2 With the blind spot monitor main switch assembly (warning canceling switch assembly) on, the voltage output...
- C1AB1 With the blind spot monitor main switch assembly (warning canceling switch assembly) on, the voltage applied...
- C1AB0 With the blind spot monitor main switch assembly (warning canceling switch assembly) on, the voltage applied...
- C1A45 A fail flag is transmitted from the skid control ECU.
- C1A47 A fail flag is transmitted from the steering angle sensor.
- Turn Signal Switch Circuit
- Main Switch Circuit
- Power Source Circuit