Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › INTUITIVE PARKING ASSIST SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049331 PARK ASSIST / MONITORING _0235786 INTUITIVE PARKING ASSIST SYSTEM J

PARK ASSIST / MONITORING  INTUITIVE PARKING ASSIST SYSTEM  Rear Clearance Sonar Sensor RH Circuit  


DESCRIPTION

The No. 2 ultrasonic sensor sends and receives ultrasonic waves. Based on the received wave, the sensor calculates the approximate distance value between the vehicle and the obstacle, and sends the distance value as a signal to the clearance warning ECU assembly.

WIRING DIAGRAM

E270572E34
4.063,1.823 4.51,2.021 0.448,0.198 10 false R2 2.427,1.406 2.802,1.604 0.375,0.198 10 false E1 2.427,1.052 2.802,1.25 0.375,0.198 10 false SOR 2.427,0.667 2.802,0.865 0.375,0.198 10 false BOR 4.417,1.406 4.667,1.604 0.25,0.198 10 false EI 4.417,1.042 4.667,1.24 0.25,0.198 10 false SI 4.417,0.667 4.667,0.865 0.25,0.198 10 false BI 2.844,1.302 3.094,1.5 0.25,0.198 10 false 13 2.844,0.938 3.094,1.135 0.25,0.198 10 false 14 2.844,0.552 3.094,0.75 0.25,0.198 10 false 12 4.208,1.302 4.396,1.5 0.188,0.198 10 false 5 4.208,0.938 4.396,1.135 0.188,0.198 10 false 3 4.208,0.552 4.396,0.75 0.188,0.198 10 false 1 4.063,1.99 5.74,2.438 1.677,0.448 10 false No. 2 Ultrasonic Sensor (Rear Corner Sensor RH) 1.5,1.854 1.948,2.052 0.448,0.198 10 false H128 1.49,2.031 3.167,2.479 1.677,0.448 10 false Clearance Warning ECU Assembly

PROCEDURE

1.INSPECT NO. 2 ULTRASONIC SENSOR (REAR CORNER SENSOR RH)
a.

Remove the No. 2 ultrasonic sensor (rear corner sensor RH) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Rear Side)>REMOVAL).


b.

Inspect the No. 2 ultrasonic sensor (rear corner sensor RH) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Rear Side)>INSPECTION).



OK

2.CHECK HARNESS AND CONNECTOR (REAR CORNER SENSOR RH - CLEARANCE WARNING ECU ASSEMBLY)

NG

REPLACE NO. 2 ULTRASONIC SENSOR (REAR CORNER SENSOR RH)

2.CHECK HARNESS AND CONNECTOR (REAR CORNER SENSOR RH - CLEARANCE WARNING ECU ASSEMBLY)
a.

Disconnect the R2 No. 2 ultrasonic sensor (rear corner sensor RH) connector.


b.

Disconnect the H128 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R2-1 (BI) - H128-12 (BOR) Always Below 1 Ω
R2-3 (SI) - H128-14 (SOR) Always Below 1 Ω
R2-5 (EI) - H128-13 (E1) Always Below 1 Ω
R2-1 (BI) or H128-12 (BOR) - Body ground Always 10 kΩ or higher
R2-3 (SI) or H128-14 (SOR) - Body ground Always 10 kΩ or higher
R2-5 (EI) or H128-13 (E1) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR