Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › INTUITIVE PARKING ASSIST SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049331 PARK ASSIST / MONITORING _0235786 INTUITIVE PARKING ASSIST SYSTEM J

PARK ASSIST / MONITORING  INTUITIVE PARKING ASSIST SYSTEM  Indicator Circuit  


DESCRIPTION

The sonar ON/OFF indicator light and warning indicator lights are installed in the accessory meter assembly.

WIRING DIAGRAM

E300606E02
0.833,4.25 1.938,4.667 1.104,0.417 10 false Accessory Meter Assembly 0.844,4.073 1.156,4.25 0.313,0.177 10 false I22 5.146,4.25 6.417,4.667 1.271,0.417 10 false Clearance Warning ECU Assembly 5.156,4.083 5.625,4.281 0.469,0.198 10 false H128 5.365,1.385 5.625,1.594 0.26,0.208 10 false L1 5.365,1.802 5.625,2.01 0.26,0.208 10 false L2 5.365,2.219 5.625,2.427 0.26,0.208 10 false L3 5.365,2.635 5.625,2.844 0.26,0.208 10 false L4 5.365,3.063 5.625,3.271 0.26,0.208 10 false L5 5.365,3.479 5.708,3.688 0.344,0.208 10 false L10 1.667,1.396 1.927,1.604 0.26,0.208 10 false RR 1.667,1.021 1.927,1.229 0.26,0.208 10 false IG 1.667,1.823 1.927,2.031 0.26,0.208 10 false RL 1.667,2.24 1.927,2.448 0.26,0.208 10 false BK 1.667,2.667 1.927,2.875 0.26,0.208 10 false FR 1.667,3.083 1.927,3.292 0.26,0.208 10 false FL 1.646,3.5 1.99,3.708 0.344,0.208 10 false OP 5.177,1.292 5.396,1.479 0.219,0.188 10 false 7 5.177,1.708 5.396,1.896 0.219,0.188 10 false 8 5.115,2.125 5.333,2.313 0.219,0.188 10 false 23 5.167,2.542 5.385,2.729 0.219,0.188 10 false 9 5.115,2.969 5.333,3.156 0.219,0.188 10 false 24 5.115,3.385 5.333,3.573 0.219,0.188 10 false 10 1.958,0.917 2.177,1.104 0.219,0.188 10 false 23 1.969,1.292 2.188,1.479 0.219,0.188 10 false 3 1.969,1.708 2.188,1.896 0.219,0.188 10 false 7 1.969,2.125 2.188,2.313 0.219,0.188 10 false 5 1.969,2.552 2.188,2.74 0.219,0.188 10 false 4 1.969,2.969 2.188,3.156 0.219,0.188 10 false 8 1.969,3.385 2.188,3.573 0.219,0.188 10 false 6 1.99,0.469 2.938,0.667 0.948,0.198 10 false ECU-IG No.1 0.219,0.323 1.49,0.573 1.271,0.25 10 false from IG No.1 Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - ACCESSORY METER ASSEMBLY)
a.

Disconnect the H128 clearance warning ECU assembly connector.


b.

Disconnect the I22 accessory meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H128-7 (L1) - I22-3 (RR) Always Below 1 Ω
H128-8 (L2) - I22-7 (RL) Always Below 1 Ω
H128-23 (L3) - I22-5 (BK) Always Below 1 Ω
H128-9 (L4) - I22-4 (FR) Always Below 1 Ω
H128-24 (L5) - I22-8 (FL) Always Below 1 Ω
H128-10 (L10) - I22-6 (OP) Always Below 1 Ω
H128-7 (L1) or I22-3 (RR) - Body ground Always 10 kΩ or higher
H128-8 (L2) or I22-7 (RL) - Body ground Always 10 kΩ or higher
H128-23 (L3) or I22-5 (BK) - Body ground Always 10 kΩ or higher
H128-9 (L4) or I22-4 (FR) - Body ground Always 10 kΩ or higher
H128-24 (L5) or I22-8 (FL) - Body ground Always 10 kΩ or higher
H128-10 (L10) or I22-6 (OP) - Body ground Always 10 kΩ or higher




OK

2.CHECK ACCESSORY METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK ACCESSORY METER ASSEMBLY
a.

Replace the accessory meter assembly with a normally functioning or new one (See page Vehicle Interior>METER / GAUGE / DISPLAY>ACCESSORY METER>REMOVAL).


b.

Check that the accessory meter assembly operates normally.

OK:

The accessory meter assembly operates normally.




OK

END (ACCESSORY METER ASSEMBLY IS DEFECTIVE)

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE