Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › INTUITIVE PARKING ASSIST SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049331 PARK ASSIST / MONITORING _0235786 INTUITIVE PARKING ASSIST SYSTEM J

PARK ASSIST / MONITORING  INTUITIVE PARKING ASSIST SYSTEM  Back Sonar Sensor RH Circuit  


DESCRIPTION

The No. 2 ultrasonic sensor sends and receives ultrasonic waves. Based on the received wave, the sensor calculates the approximate distance value between the vehicle and the obstacle, and sends the distance value as a signal to the clearance warning ECU assembly.

WIRING DIAGRAM

E270572E30
4.01,1.833 4.458,2.031 0.448,0.198 10 false R3 2.521,1.417 2.802,1.615 0.281,0.198 10 false EO 2.521,1.052 2.802,1.25 0.281,0.198 10 false SO 2.521,0.677 2.802,0.875 0.281,0.198 10 false BO 4.417,1.406 4.667,1.604 0.25,0.198 10 false EI 4.417,1.042 4.667,1.24 0.25,0.198 10 false SI 4.417,0.656 4.667,0.854 0.25,0.198 10 false BI 2.833,1.302 3.021,1.5 0.188,0.198 10 false 6 2.833,0.927 3.021,1.125 0.188,0.198 10 false 4 2.833,0.563 3.021,0.76 0.188,0.198 10 false 2 4.229,1.302 4.417,1.5 0.188,0.198 10 false 5 4.219,0.927 4.406,1.125 0.188,0.198 10 false 3 4.219,0.552 4.406,0.75 0.188,0.198 10 false 1 4.01,1.99 5.688,2.438 1.677,0.448 10 false No. 2 Ultrasonic Sensor (Rear Center Sensor RH) 1.5,1.844 1.948,2.042 0.448,0.198 10 false R2 1.5,2.01 3.177,2.458 1.677,0.448 10 false No. 2 Ultrasonic Sensor (Rear Corner Sensor RH)

PROCEDURE

1.INSPECT NO. 2 ULTRASONIC SENSOR (REAR CENTER SENSOR RH)
a.

Replace the No. 2 ultrasonic sensor (rear center sensor RH) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Rear Side)>REMOVAL).


b.

Inspect the No. 2 ultrasonic sensor (rear center sensor RH) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Rear Side)>INSPECTION).



OK

2.CHECK HARNESS AND CONNECTOR (REAR CENTER SENSOR RH - REAR CORNER SENSOR RH)

NG

REPLACE NO. 2 ULTRASONIC SENSOR (REAR CENTER SENSOR RH)

2.CHECK HARNESS AND CONNECTOR (REAR CENTER SENSOR RH - REAR CORNER SENSOR RH)
a.

Disconnect the R3 No. 2 ultrasonic sensor (rear center sensor RH) connector.


b.

Disconnect the R2 No. 2 ultrasonic sensor (rear corner sensor RH) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R3-1 (BI) - R2-2 (BO) Always Below 1 Ω
R3-3 (SI) - R2-4 (SO) Always Below 1 Ω
R3-5 (EI) - R2-6 (EO) Always Below 1 Ω
R3-1 (BI) or R2-2 (BO) - Body ground Always 10 kΩ or higher
R3-3 (SI) or R2-4 (SO) - Body ground Always 10 kΩ or higher
R3-5 (EI) or R2-6 (EO) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR