Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › INTUITIVE PARKING ASSIST SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049331 PARK ASSIST / MONITORING _0235786 INTUITIVE PARKING ASSIST SYSTEM D

PARK ASSIST / MONITORING  INTUITIVE PARKING ASSIST SYSTEM  OPERATION CHECK  


CHECK INITIAL CHECK FUNCTION


E303034E02
1.208,0.792 1.469,0.792 1.469,0.792 1.469,1.635 false 0.104,0.094 0.5,0.281 0.396,0.188 10 false LED 0.292,0.698 1.208,1.083 0.917,0.385 10 false Approximately 0.4 seconds 1.719,1.26 2.948,1.427 1.229,0.167 10 false 0.7 to 1.3 seconds 0.583,1.76 0.958,1.927 0.375,0.167 10 false ON 0.594,2.115 0.969,2.281 0.375,0.167 10 false OFF 0.104,1.813 0.448,1.99 0.344,0.177 10 false LED 0.531,2.448 1.677,2.76 1.146,0.313 10 false Main Switch ON 2.01,2.5 3.083,2.854 1.073,0.354 10 false Detection Operation Starts

a.

Check the initial check function for the LED.

i.

When the clearance sonar main switch is turned ON, check that the following occurs: 1) after 0.4 seconds, the LEDs are turned on for approximately 0.7 to 1.3 seconds, and 2) the system starts the obstacle detection operation.



b.

Check the initial check function for the sensor.

·

Approximately 0.4 seconds after the ignition switch has been turned to ON and the clearance sonar main switch has been turned ON, all sensors will be checked by the system.

·

After 0.7 to 1.3 seconds have elapsed, the check operation for all of the sensors will stop when a vehicle speed of over 10 km/h (6 mph) is detected.

·

When the vehicle has been shifted from P, the system will change to obstacle detection operation according to the shift lever position.

·

If there are no changes in the conditions, such as those listed above (speed or shift lever position), the sensor check operation will be halted after 5 +/-1 second have elapsed. If one or more sensors are anomalous, check operation for all of the sensors will continue (sensors will continue transmitting).



c.

If the sensor is found to have an anomaly due to an open circuit or freezing for approximately 5 seconds or more, indications as shown in the following illustration appear.

i.

When the ECU judges that the sensor needs to be repaired:

E303037E02
2.323,0.698 2.167,0.135 2.167,0.135 2.042,0.135 false 2.375,0.438 2.594,0.208 2.594,0.208 2.667,0.208 false 2.969,1.104 3.25,0.823 3.25,0.823 3.323,0.823 false 6.25,0.927 6.927,1.313 0.677,0.385 10 false Returns to Normal 5.5,1.688 5.771,1.844 0.271,0.156 10 false *2 2.833,1.677 3.104,1.833 0.271,0.156 10 false *1 1.51,1.24 1.896,1.406 0.385,0.167 10 false ON 1.5,1.479 1.885,1.646 0.385,0.167 10 false OFF 1.5,1.885 1.885,2.052 0.385,0.167 10 false ON 1.5,2.104 1.885,2.271 0.385,0.167 10 false OFF 1.51,2.542 1.896,2.708 0.385,0.167 10 false ON 1.5,2.76 1.885,2.927 0.385,0.167 10 false OFF 0.375,1.333 0.688,1.51 0.313,0.177 10 false LED 0.365,1.906 0.865,2.083 0.5,0.177 10 false Buzzer 0.365,2.583 1.396,2.76 1.031,0.177 10 false Power Indicator 0.146,3.188 4.969,3.365 4.823,0.177 10 false *1: Only the LEDs of the malfunctioning sensor 0.156,3.458 4.979,3.635 4.823,0.177 10 false *2: The LEDs of all sensors 0.344,0.063 2.063,0.427 1.719,0.365 10 false Approximately 1.5 seconds (1 Cycle) 2.719,0.125 5.125,0.313 2.406,0.188 10 false Approximately 7.5 seconds (5 Cycles) 3.365,0.74 5.115,0.938 1.75,0.198 10 false Approximately 0.75 seconds 0.552,0.865 1.792,1.219 1.24,0.354 10 false Approximately 0.25 seconds


ii.

When the ECU judges that the sensor needs to be cleaned:

E303038E02
2.365,0.417 2.469,0.167 2.469,0.167 2.552,0.167 false 2.219,0.792 2.146,0.146 2.146,0.146 2.031,0.146 false 2.875,1.208 3.208,0.938 3.208,0.938 3.25,0.938 false 0.156,3.229 4.979,3.406 4.823,0.177 10 false *1: Only the LEDs of the malfunctioning sensor 0.167,3.5 4.99,3.677 4.823,0.177 10 false *2: The LEDs of all sensors 6.292,0.833 6.979,1.271 0.688,0.438 10 false Returns to Normal 1.438,1.25 1.823,1.417 0.385,0.167 10 false ON 1.438,1.458 1.823,1.625 0.385,0.167 10 false OFF 1.438,2.021 1.823,2.188 0.385,0.167 10 false ON 1.438,2.25 1.823,2.417 0.385,0.167 10 false OFF 1.448,2.698 1.833,2.865 0.385,0.167 10 false ON 1.448,2.906 1.833,3.073 0.385,0.167 10 false OFF 0.313,1.333 0.625,1.51 0.313,0.177 10 false LED 0.313,2.104 0.813,2.281 0.5,0.177 10 false Buzzer 0.313,2.729 1.292,2.927 0.979,0.198 10 false Power Indicator 0.313,0.073 2.031,0.438 1.719,0.365 10 false Approximately 1.5 seconds (1 Cycle) 2.604,0.083 5.01,0.271 2.406,0.188 10 false Approximately 7.5 seconds (5 Cycles) 3.302,0.854 5.094,1.042 1.792,0.188 10 false Approximately 0.75 seconds 2.802,1.688 3.01,1.875 0.208,0.188 10 false *1 5.604,1.688 5.813,1.875 0.208,0.188 10 false *2 0.792,0.75 1.76,1.115 0.969,0.365 10 false Approximately 0.25 seconds

HINT:

If the clearance sonar main switch is ON and the ignition switch is turned to ON, the buzzer does not sound.





DETECTION RANGE MEASUREMENT AND INDICATOR CHECK


NOTICE:

Apply the parking brake securely so that the vehicle does not move.


a.

Turn the ignition switch to ON.


b.

Move the shift lever to R to check the front corner sensors, rear corner sensors and back sensors.


c.

Move the shift lever to D, S or N to check the front corner sensors.


d.

Turn the clearance sonar main switch ON.


e.

Move a pole around the sensor to measure the detection range of the sensor.

NOTICE:
·

These detection ranges are applicable when positioning the pole parallel or perpendicular to the ground.

·

The ranges vary depending on the measuring method and type of obstacle (such as walls).

·

For close-range, medium-range and long-range detection, the values shown are for when using a pole with a diameter of 60 mm (2.36 in.). For longest-range detection, the values shown are for when using a pole with a diameter of 400 mm (15.7 in.).



i.

Front corner sensors detection range

E300425E02
1.625,0.177 4.708,0.385 3.083,0.208 10 false Approximately 600 +/- 60 mm (23.6 +/- 2.36 in.) 0.25,0.656 0.625,0.906 0.375,0.25 10 false A 0.26,3.177 0.635,3.427 0.375,0.25 10 false A 1.708,0.698 3.885,0.906 2.177,0.208 10 false Approximately 200 mm (7.87 in.) 4.406,1.521 4.677,1.76 0.271,0.24 10 false *1 2.813,1.698 3.896,2.094 1.083,0.396 10 false Approximately 450 mm (17.7 in.) 2.823,2.292 3.917,2.698 1.094,0.406 10 false Approximately 550 mm (21.7 in.)

HINT:

*1: The No. 2 ultrasonic sensor side view detection ranges hatched area represents the cross section of the top view detection range A lines. The hatched area does not represent the entire side view detection range.



ii.

Rear corner sensors detection range

U154198E02
1.323,0.208 1.792,0.615 1.792,0.615 1.792,0.75 false 2.219,0.875 3.021,0.177 false 0.26,0.115 1.333,0.542 1.073,0.427 10 false Approximately 200 mm (7.87 in.) 3.094,0.083 5.135,0.438 2.042,0.354 10 false Approximately 1800 +/- 180 mm (70.9 +/- 7.09 in.) 5.708,1.354 6.802,1.74 1.094,0.385 10 false Approximately 600 mm (23.6 in.) 5.708,3.01 6.792,3.354 1.083,0.344 10 false Approximately 300 mm (11.8 in.)


iii.

Back sensors detection range

U154199E02
6.323,2.865 6.594,3.385 6.594,3.385 6.469,3.385 false 2.583,0.656 1.76,0.177 false 2.083,0.927 1.25,0.74 false 0.198,0.115 1.781,0.479 1.583,0.365 10 false Approximately 850 +/- 90 mm (33.5 +/- 3.54 in.) 0.219,0.646 1.313,1.042 1.094,0.396 10 false Approximately 200 mm (7.87 in.) 3.406,3.094 3.667,3.292 0.26,0.198 10 false A 5.635,2.042 5.865,2.25 0.229,0.208 10 false *1 5.479,1.115 6.583,1.5 1.104,0.385 10 false Approximately 550 mm (21.7 in.) 4.448,3.302 6.49,3.531 2.042,0.229 10 false Approximately 400 mm (15.7 in.)

HINT:

*1: The No. 2 ultrasonic sensor side view detection ranges hatched area represents the cross section of the top view detection range A lines. The hatched area does not represent the entire side view detection range.




f.

When the ultrasonic sensors have detected an obstacle, check the accessory meter and buzzer sounds with the clearance sonar main switch ON.

Operation Condition
Shift Lever Position Vehicle Speed Buzzer Detection, Accessory Meter Detection
Front Corner LH
Front Corner RH
Back LH
Back RH
Rear Corner LH
Rear Corner RH
P - X X X
D, S, (N) 10 km/h (6.2 mph) or less ○ X X
R No Limit ○ ○ ○

i.

Check the buzzer sounds with the clearance sonar main switch ON.

E270549E03
0.104,0.146 1.771,0.354 1.667,0.208 10 false 1. Close-range Detection 0.104,1.01 2.135,1.219 2.031,0.208 10 false 2. Medium-range Detection 0.104,2.26 1.896,2.469 1.792,0.208 10 false 3. Long-range Detection 2.49,0.365 2.792,0.51 0.302,0.146 10 false ON 2.49,0.792 2.854,0.938 0.365,0.146 10 false OFF 2.49,1.635 2.792,1.781 0.302,0.146 10 false ON 2.49,2.073 2.854,2.219 0.365,0.146 10 false OFF 2.49,2.865 2.792,3.01 0.302,0.146 10 false ON 2.49,3.292 2.854,3.438 0.365,0.146 10 false OFF 1.281,1.302 2.698,1.458 1.417,0.156 10 false 0.75 +/-0.075 seconds 1.271,2.521 2.729,2.677 1.458,0.156 10 false 0.15 +/-0.015 seconds 4.719,2.521 6.26,2.677 1.542,0.156 10 false 0.15 +/-0.015 seconds 0.104,3.438 1.896,3.646 1.792,0.208 10 false 4. Longest-range Detection 2.49,4.01 2.792,4.156 0.302,0.146 10 false ON 2.49,4.448 2.854,4.594 0.365,0.146 10 false OFF 1.281,3.688 2.813,3.844 1.531,0.156 10 false 0.15 +/-0.015 seconds 5.323,3.667 6.75,3.823 1.427,0.156 10 false 0.65 +/-0.065 seconds 4.365,1.313 6.24,1.469 1.875,0.156 10 false 0.75 +/-0.075 seconds

Front Corner Detection Range
Detection Distance
1. Close-range detection Within 300 +/- 30 mm (11.8 +/- 1.18 in.)
2. Medium-range detection 300 +/- 30 to 450 +/- 50 mm (11.8 +/- 1.18 to 17.7 +/- 1.97 in.)
3. Long-range detection 450 +/- 50 to 600 +/- 60 mm (17.7 +/- 1.97 to 23.6 +/- 2.36 in.)

Rear Corner Detection Range
Detection Distance
1. Close-range detection Within 400 +/- 40 mm (15.7 +/- 1.57 in.)
2. Medium-range detection 400 +/- 40 to 600 +/- 60 mm (15.7 +/- 1.57 to 23.6 +/- 2.36 in.)
3. Long-range detection 600 +/- 60 to 850 +/- 90 mm (23.6 +/- 2.36 to 33.5 +/- 3.54 in.)

Back Detection Range
Detection Distance
1. Close-range detection Within 500 +/- 50 mm (19.7 +/- 1.97 in.)
2. Medium-range detection 500 +/- 50 to 750 +/- 80 mm (19.7 +/- 1.97 to 29.5 +/- 3.15 in.)
3. Long-range detection 750 +/- 80 to 1000 +/- 100 mm (29.5 +/- 3.15 to 39.4 +/- 3.94 in.)
4. Longest-range detection (to wall) 1000 +/- 100 to 1800 +/- 180 mm (39.4 +/- 3.94 to 70.9 +/- 7.09 in.)

HINT:

Ultrasonic waves are used to measure the detection range. However, the detection range may vary depending on the ambient temperature.



ii.

Check the indicator and buzzer on the accessory meter when the front corner sensors have detected an obstacle.

Operation Condition
Ignition Switch Clearance Sonar Main Switch Shift Lever Position Vehicle Speed
ON ON D, S, N 10 km/h (6.2 mph) or less

E344969

Accessory Meter
Detection Range Buzzer Indicator Displayed
1. Close-range detection Sounds continuously Corner indicator(s) are illuminated
2. Medium-range detection Sounds intermittently
(ON: 75 msec. / OFF: 75 msec.)
Corner indicator(s) are blinking
3. Long-range detection Sounds intermittently
(ON: 150 msec. / OFF: 150 msec.)
Corner indicator(s) are blinking

HINT:

Ultrasonic waves are used to measure the detection range. However, the detection range may vary depending on the ambient temperature.



iii.

Check the accessory meter and buzzer when the front corner sensors, back sensors and rear corner sensors have detected an obstacle.

Operation Condition
Ignition Switch Clearance Sonar Main Switch Shift Lever Position
ON ON R position

E344970

Accessory Meter
Detection Range Buzzer Indicator Displayed
1. Close-range detection Sounds continuously Corner indicator(s) are illuminated and/or back indicator is illuminated
2. Medium-range detection Sounds intermittently
(ON: 75 msec. / OFF: 75 msec.)
Corner indicator(s) are blinking and/or back indicator is blinking
3. Long-range detection Sounds intermittently
(ON: 150 msec. / OFF: 150 msec.)
Corner indicator(s) are blinking and/or back indicator is blinking
4. Longest-range detection Sounds intermittently
(ON: 150 msec. / OFF: 650 msec.)
Back indicator is blinking

HINT:

Ultrasonic waves are used to measure the detection range. However, the detection range may vary depending on the ambient temperature.