Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049331 PARK ASSIST / MONITORING _0235792 BLIND SPOT MONITOR SYSTEM U

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Data List.


e.

Read the Data List according to the display on the Techstream.

Blind Spot Monitor Master
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
BSM Main Switch Blind spot monitor main switch assembly (warning canceling switch assembly) / OFF or ON ON: Blind spot monitor main switch assembly (warning canceling switch assembly) on
OFF: Blind spot monitor main switch assembly (warning canceling switch assembly) off
-
Master Side Turn Switch Master side turn switch / OFF or ON ON: Right turn switch on
OFF: Right turn switch off
This item is always OFF for vehicles which send and receive this signal via CAN communication.
Signal Noise Ratio(Tilt:ch1) Target radar emission received by narrow-angle antenna / Min.: 0 db, Max.: 249 db Depends on settings (Initial value 0 dB) This item is not supported.
BSM Warning Indicator Turning on(Master) Blind spot monitor indicator RH illumination state / OFF or ON

OFF: Except below

ON: All of following conditions met

·

Initial check not being performed

·

Vehicle detected in right side warning area

·

Right turn signal off

·

Vehicle speed 40 km/h (25 mph) or more

·

Shift lever not in R

·

Blind spot monitor system warning message not displayed



-
BSM Warning Indicator Flashing(Master) Blind spot monitor indicator RH flashing state / OFF or ON

OFF: Except below

ON: All of following conditions met

·

Initial check not being performed

·

Vehicle detected in right side warning area

·

Right turn signal off

·

Vehicle speed 40 km/h (25 mph) or more

·

Shift lever not in R

·

Blind spot monitor system warning message not displayed



-
Turn Switch State Master side, slave side state of the turn switch / Master ON, Slave ON or OFF Master ON: Right turn switch on
Slave ON: Left turn switch on
OFF: Switch not operated
-
Master Side Turn Signal State of the master side turn signal / OFF or ON ON: Right turn signal received
OFF: Right turn signal not received
-
Reverse State of the shift position R signal / OFF or ON ON: Shift lever in R
OFF: Shift lever in any position except R
-
Vehicle Speed Vehicle speed signal / Min.: 0 km/ h (0 mph), Max.: 326 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) -
Steering Angle Steering angle sensor / Min.: - 3072°, Max.: 3070.5° Left turn: Increases
Right turn: Decreases
-
VGRS Relative Angle Compensation value of steering angle calculated by VGRS / Min.: -8.192 rad, Max.: 8.191 rad Left turn: Increases
Right turn: Decreases
This item is only for vehicles with the VGRS system.
Power Supply Voltage Power supply voltage / Min.: 0 V, Max.: 50 V 11 to 14 V -
HV Flag Hybrid vehicle / OFF or ON OFF: Non-hybrid vehicle
ON: Hybrid vehicle
-
VGRS Flag VGRS installed / OFF or ON OFF: VGRS not installed
ON: VGRS installed
-
BSM Main SW Inspection Completeness Flag Completion of inspection for blind spot monitor main switch (warning canceling assembly) / Incompl or Compl Incompl: Inspection not completed
Compl: Inspection completed
Changes to Compl when the blind spot monitor main switch (warning canceling assembly) is changed from off to on during Test Mode.
Beam Axis Inspection Completeness Flag Completion of beam axis inspection / Incompl or Compl Incompl: Inspection not completed
Compl: Inspection completed
Changes to Compl when Test Mode has been entered.
Number of DTC Number of DTCs / Min.: 0, Max.: 255 When system normal: 0
When malfunction detected: More than 0
-

Blind Spot Monitor Slave
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Slave Side Turn Switch Slave side turn switch / OFF or ON ON: Left turn switch on
OFF: Left turn switch off
This item is always OFF for vehicles which send and receive this signal via CAN communication.
BSM Warning Indicator Turning on(Slave) Blind spot monitor indicator LH illumination state / OFF or ON

OFF: Except below

ON: All of following conditions met

·

Initial check not being performed

·

Vehicle detected in left side warning area

·

Left turn signal off

·

Vehicle speed 40 km/h (25 mph) or more

·

Shift lever not in R

·

Blind spot monitor system warning message not displayed



-
BSM Warning Indicator Flashing(Slave) Blind spot monitor indicator LH flashing state / OFF or ON

OFF: Except below

ON: All of following conditions met

·

Initial check not being performed

·

Vehicle detected in left side warning area

·

Left turn signal off

·

Vehicle speed 40 km/h (25 mph) or more

·

Shift lever not in R

·

Blind spot monitor system warning message not displayed



-
Turn Switch State Master side, slave side state of the turn switch / Master ON, Slave ON or OFF Master ON: Right turn switch on
Slave ON: Left turn switch on
OFF: Switch not operated
-
Slave Side Turn Signal State of the slave side turn signal / OFF or ON ON: Left turn signal received
OFF: Left turn signal not received
-
Reverse State of the shift position R signal / OFF or ON ON: Shift lever in R
OFF: Shift lever in any position except R
-
Vehicle Speed Vehicle speed signal / Min.: 0 km/ h (0 mph), Max.: 326 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) -
Steering Angle Steering angle sensor / Min.: - 3072°, Max.: 3070.5° Left turn: Increases
Right turn: Decreases
-
VGRS Relative Angle Compensation value of steering angle calculated by VGRS / Min.: -8.192 rad, Max.: 8.191 rad Left turn: Increases
Right turn: Decreases
This item is only for vehicles with the VGRS system.
Power Supply Voltage Power supply voltage / Min.: 0 V, Max.: 50 V 11 to 14 V -
HV Flag Hybrid vehicle / OFF or ON OFF: Non-hybrid vehicle
ON: Hybrid vehicle
-
VGRS Flag VGRS installed / OFF or ON OFF: VGRS not installed
ON: VGRS installed
-
Beam Axis Inspection Completeness Flag Completion of beam axis inspection / Incompl or Compl Incompl: Inspection not completed
Compl: Inspection completed
Changes to Compl when Test Mode has been entered.
Number of DTC Number of DTCs / Min.: 0, Max.: 255 When system normal: 0
When malfunction detected: More than 0
-