FREEZE FRAME DATA
Whenever a DTC is stored, the blind spot monitor sensor stores the current vehicle (sensor) state as Freeze Frame Data.
CHECK FREEZE FRAME DATA
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Trouble Codes.
According to the display on the Techstream, select the trouble code data display with Freeze Frame Data.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Turn Switch State | Master side, slave side state of the turn switch / Master ON, Slave ON or OFF | Master ON: Right turn switch on
Slave ON: Left turn switch on OFF: Switch not operated |
- |
| Master Side Turn Signal | State of the master side turn signal / OFF or ON | ON: Right turn signal received
OFF: Right turn signal not received |
- |
| Reverse | State of the shift position R signal / OFF or ON | ON: Shift lever in R
OFF: Shift lever in any position except R |
- |
| Vehicle Speed | Vehicle speed signal / Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) | Vehicle stopped: 0 km/h (0 mph) | - |
| Steering Angle | Steering angle sensor / Min.: -3072°, Max.: 3070.5° | Left turn: Increases
Right turn: Decreases |
- |
| VGRS Relative Angle | Compensation value of steering angle calculated by VGRS / Min.: -8.192 rad, Max.: 8.191 rad | Left turn: Increases
Right turn: Decreases |
This item is only for vehicles with the VGRS system. |
| Power Supply Voltage | Power supply voltage / Min.: 0 V, Max.: 50 V | 11 to 14 V | - |
| BSM Warning Indicator Turning on (Master) | Blind spot monitor indicator RH illumination state / OFF or ON | OFF: Except below
ON: All of following conditions met ·
Initial check not being performed ·
Vehicle detected in right side warning area ·
Right turn signal off ·
Vehicle speed 40 km/h (25 mph) or more ·
Shift lever not in R ·
Blind spot monitor system warning message not displayed |
- |
| BSM Warning Indicator Flashing (Master) | Blind spot monitor indicator RH flashing state / OFF or ON | OFF: Except below
ON: All of following conditions met ·
Initial check not being performed ·
Vehicle detected in right side warning area ·
Right turn signal on ·
Vehicle speed 40 km/h (25 mph) or more ·
Shift lever not in R ·
Blind spot monitor system warning message not displayed |
- |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Turn Switch State | Master side, slave side state of the turn switch / Master ON, Slave ON or OFF | Master ON: Right turn switch on
Slave ON: Left turn switch on OFF: Switch not operated |
- |
| Slave Side Turn Signal | State of the slave side turn signal / OFF or ON | ON: Left turn signal received
OFF: Left turn signal not received |
- |
| Reverse | State of the shift position R signal / OFF or ON | ON: Shift lever in R
OFF: Shift lever in any position except R |
- |
| Vehicle Speed | Vehicle speed signal / Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) | Vehicle stopped: 0 km/h (0 mph) | - |
| Steering Angle | Steering angle sensor / Min.: -3072°, Max.: 3070.5° | Left turn: Increases
Right turn: Decreases |
- |
| VGRS Relative Angle | Compensation value of steering angle calculated by VGRS / Min.: -8.192 rad, Max.: 8.191 rad | Left turn: Increases
Right turn: Decreases |
This item is only for vehicles with the VGRS system. |
| Power Supply Voltage | Power supply voltage / Min.: 0 V, Max.: 50 V | 11 to 14 V | - |
| BSM Warning Indicator Flashing (Slave) | Blind spot monitor indicator LH illumination state / OFF or ON | OFF: Except below
ON: All of following conditions met ·
Initial check not being performed ·
Vehicle detected in left side warning area ·
Left turn signal off ·
Vehicle speed 40 km/h (25 mph) or more ·
Shift lever not in R ·
Blind spot monitor system warning message not displayed |
- |
| BSM Warning Indicator Flashing (Slave) | Blind spot monitor indicator LH flashing state / OFF or ON | OFF: Except below
ON: All of following conditions met ·
Initial check not being performed ·
Vehicle detected in left side warning area ·
Left turn signal on ·
Vehicle speed 40 km/h (25 mph) or more ·
Shift lever not in R ·
Blind spot monitor system warning message not displayed |
- |
CLEAR FREEZE FRAME DATA
Clearing the DTCs will also clear the Freeze Frame Data.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs and Freeze Frame Data.