Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR MAIN SWITCH
RM27L0U _56 Audio / Visual / Telematics _049331 PARK ASSIST / MONITORING _0235793 BLIND SPOT MONITOR MAIN SWITCH G

PARK ASSIST / MONITORING  BLIND SPOT MONITOR MAIN SWITCH  INSPECTION  


PROCEDURE

Hide 84470 1.INSPECT BLIND SPOT MONITOR MAIN SWITCH ASSEMBLY (WARNING CANCELING SWITCH ASSEMBLY)

a.
E224422E18
1.969,1.385 2.552,0.677 false 1.479,1.438 1.833,1.927 1.833,1.927 1.938,1.927 false 2.625,0.583 2.75,0.74 0.125,0.156 10 false D 2.01,1.854 2.135,2.01 0.125,0.156 10 false B 0.167,0.146 0.344,0.302 0.177,0.156 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
11 (B) - 8 (D) Blind spot monitor main switch assembly (warning canceling switch assembly) on Below 1 Ω
11 (B) - 8 (D) Blind spot monitor main switch assembly (warning canceling switch assembly) off 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Blind Spot Monitor Main Switch Assembly (Warning Canceling Switch Assembly))

If the result is not as specified, replace the blind spot monitor main switch assembly (warning canceling switch assembly).


b.

Check that the switch illuminates.

i.
E224422E06
1.807,1.454 2.168,1.947 2.168,1.947 2.271,1.947 false 2.288,1.856 2.638,2.016 0.350,0.161 10 ILL- 0.168,0.148 0.342,0.304 0.174,0.156 10 *a 1.669,1.454 1.379,1.947 1.379,1.947 1.296,1.947 false 0.926,1.856 1.238,2.016 0.312,0.161 10 ILL+

Apply battery voltage to the blind spot monitor main switch assembly (warning canceling switch assembly) and check that the switch illuminates.

OK:
Connection Specified Condition
Battery positive (+) → Terminal 10 (ILL+)
Battery negative (-) → Terminal 9 (ILL-)
Illuminates


Text in Illustration
*a Component without harness connected
(Blind Spot Monitor Main Switch Assembly (Warning Canceling Switch Assembly))

If the result is not as specified, replace the warning canceling switch assembly (warning canceling switch assembly).



c.

Check that the switch indicator operates.

i.
E224422E07
1.289,1.396 0.664,1.346 false 1.497,1.454 1.858,1.947 1.858,1.947 1.961,1.947 false 0.528,1.248 0.656,1.409 0.128,0.161 10 E 2.013,1.856 2.141,2.016 0.128,0.161 10 B 0.168,0.148 0.342,0.304 0.174,0.156 10 *a

Apply battery voltage to the blind spot monitor main switch assembly (warning canceling switch assembly) and check the operation of the switch as shown in the table below.

OK:
Connection Switch Condition Specified Condition
Battery positive (+) → Terminal 11 (B)
Battery negative (-) → Terminal 12 (E)
Blind spot monitor main switch assembly (warning canceling switch assembly) on Indicator Illuminates


Text in Illustration
*a Component without harness connected
(Blind Spot Monitor Main Switch Assembly (Warning Canceling Switch Assembly))

If the result is not as specified, replace the blind spot monitor main switch assembly (warning canceling switch assembly).