This DTC is stored if the radio and display receiver assembly judges as a result of its self check that the signals or signal lines between the radio and display receiver assembly and the rear television camera assembly are not normal.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1622 | Open or Short Circuit in rear television camera signal | ·
Harness or connector ·
Rear television camera assembly ·
Radio and display receiver assembly |
Check for DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>REAR VIEW MONITOR SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| No DTC is output | A |
| DTC is output | B |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
Disconnect the I62 radio and display receiver assembly connector.
Disconnect the V23 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I62-11 (CA+) - V23-6 (CB+) | Always | Below 1 Ω |
| I62-12 (V+) - V23-3 (CV+) | Always | Below 1 Ω |
| I62-23 (CGND) - V23-5 (CGND) | Always | Below 1 Ω |
| I62-24 (V-) - V23-2 (CV-) | Always | Below 1 Ω |
| I62-11 (CA+) - Body ground | Always | 10 kΩ or higher |
| I62-12 (V+) - Body ground | Always | 10 kΩ or higher |
| I62-23 (CGND) - Body ground | Always | 10 kΩ or higher |
| I62-24 (V-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I62-23 (CGND) - Body ground | Always | Below 1 Ω |
| I62-24 (V-) - Body ground | Always | Below 1 Ω |
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
OK
NG
Disconnect the rear television camera assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| V23-6 (CB+) - V23-5 (CGND) | Ignition switch ACC | 5.5 to 7.05 V |
| *a | Front view of wire harness connector
(to Rear Television Camera Assembly) |
OK
NG
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
*b | Waveform 1 |
| *c | Waveform 2 | *d | Synchronized Signal |
| *e | Video Waveform | - | - |
| Item | Content |
|---|---|
| Tester Connection | I62-12 (V+) - I62-24 (V-) |
| Tool Setting | 0.2 V/DIV., 50 μs/DIV. |
| Condition | Waveform 1: Ignition switch ON, shift lever in R Waveform 2: Ignition switch ON, shift lever in R, screen blacked out by covering camera lens |
Waveform is as shown in illustration.
The video waveform changes according to the image sent by the rear television camera assembly.
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
Replace the rear television camera assembly with a new or normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA>REMOVAL).
NEXT
Check for DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>REAR VIEW MONITOR SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| No DTC is output | A |
| DTC is output | B |
A
B