Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM27L0U _57 Power Source / Network _049335 NETWORKING _0235802 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Gateway ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Gateway ECU Communication Stop Mode Either condition is met:
·

"CAN Gateway1" is not displayed on the "Bus Check" screen.

·

"Gateway ECU Communication Stop Mode" in "DTC Communication Table" applies.


·

Power source or inside of network gateway ECU

·

Network gateway ECU CAN branch wire or connector

·

Network gateway ECU



For vehicles with an network gateway ECU.


WIRING DIAGRAM

C242979E01
5.457,4.835 5.831,4.981 0.373,0.147 10 H120 5.8,4.225 6.206,4.363 0.406,0.137 10 GND 5.609,4.13 5.705,4.267 0.096,0.137 10 4 5.609,3.485 5.705,3.622 0.096,0.137 10 9 5.529,2.845 5.704,2.983 0.174,0.137 10 10 5.8,1.388 6.206,1.525 0.406,0.137 10 CA1L 5.529,1.292 5.704,1.429 0.174,0.137 10 15 5.529,0.849 5.704,0.986 0.174,0.137 10 16 1.937,1.292 2.111,1.429 0.174,0.137 10 17 5.8,0.944 6.206,1.082 0.406,0.137 10 CA1H 1.937,0.849 2.111,0.986 0.174,0.137 10 6 5.8,3.581 6.206,3.718 0.406,0.137 10 IG2 5.8,2.941 6.206,3.078 0.406,0.137 10 IG1 5.8,2.297 6.206,2.434 0.406,0.137 10 BATT 2.37,2.941 3.653,3.078 1.283,0.137 10 from IG1 No.3 Relay 2.699,3.59 3.656,3.728 0.957,0.137 10 from IG2 Relay 2.882,2.297 3.658,2.434 0.776,0.137 10 from Battery 5.609,2.201 5.705,2.338 0.096,0.137 10 2 5.457,4.989 6.937,5.135 1.480,0.147 10 Network Gateway ECU 0.862,1.791 1.221,1.938 0.360,0.147 10 H115 0.862,1.945 2.494,2.092 1.633,0.147 10 No. 2 Junction Connector 4.707,3.429 4.973,3.566 0.266,0.137 10 IGN 4.416,2.792 5.258,2.929 0.842,0.137 10 ECU-IG No.2 4.569,2.158 5.109,2.295 0.540,0.137 10 ECU-B1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (NETWORK GATEWAY ECU CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (NETWORK GATEWAY ECU CAN BRANCH WIRE)
a.
U153772E01
2.741,1.136 3.098,1.273 0.357,0.137 10 H120 1.246,1.243 1.037,1.018 1.037,1.018 0.914,1.018 false 1.031,1.637 1.103,1.637 1.103,1.637 1.355,1.293 false 0.424,0.944 0.813,1.081 0.389,0.137 10 CA1H 0.582,1.551 0.970,1.688 0.389,0.137 10 CA1L 0.07,0.056 0.371,0.193 0.301,0.137 10 *a

Disconnect the H120 network gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H120-16 (CA1H) - H120-15 (CA1L) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Network Gateway ECU)



OK

4.CHECK HARNESS AND CONNECTOR (NETWORK GATEWAY ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE NETWORK GATEWAY ECU CAN BRANCH WIRE OR CONNECTOR (CA1H, CA1L)

4.CHECK HARNESS AND CONNECTOR (NETWORK GATEWAY ECU - BATTERY AND BODY GROUND)
a.
U153771E01
2.037,1.295 2.43,1.583 2.43,1.583 2.553,1.583 false 2.215,1.935 2.144,1.935 2.144,1.935 1.929,1.293 false 2.567,1.508 2.956,1.646 0.389,0.137 10 IG2 2.61,0.709 2.999,0.846 0.389,0.137 10 BATT 0.604,0.709 0.993,0.846 0.389,0.137 10 GND 2.234,1.866 2.623,2.004 0.389,0.137 10 IG1 0.501,1.136 0.858,1.273 0.357,0.137 10 H120 0.07,0.056 0.371,0.193 0.301,0.137 10 *a 1.35,1.097 1.101,0.786 1.101,0.786 1.029,0.786 false 2.278,1.097 2.527,0.786 2.527,0.786 2.598,0.786 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H120-2 (BATT) - Body ground Always 11 to 14 V
H120-10 (IG1) - Body ground Ignition switch ON 11 to 14 V
H120-9 (IG2) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H120-4 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Rear view of wire harness connector
(to Network Gateway ECU)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR