Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM27L0U _57 Power Source / Network _049335 NETWORKING _0235802 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Power Steering ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Power Steering ECU Communication Stop Mode Either condition is met:
·

"Power Steering (EPS)" is not displayed on the "Bus Check" screen.

·

"Power Steering ECU Communication Stop Mode" in "DTC Communication Table" applies.


·

Power source or inside of power steering ECU assembly

·

Power steering ECU assembly CAN branch wire or connector

·

Power steering ECU assembly



WIRING DIAGRAM

C245661E02
0.609,1.601 2.226,1.744 1.617,0.143 10 No. 1 Junction Connector 5.758,0.635 6.275,0.773 0.517,0.138 10 CANH 5.758,1.074 6.275,1.213 0.517,0.138 10 CANL 5.504,0.977 5.599,1.116 0.095,0.139 10 2 5.501,2.958 5.599,3.097 0.098,0.139 10 3 5.498,2.147 5.599,2.286 0.101,0.139 10 5 5.504,0.533 5.599,0.672 0.095,0.139 10 1 5.76,3.066 6.277,3.203 0.517,0.137 10 GND 1.562,2.268 2.853,2.405 1.291,0.137 10 from IG1 No.3 Relay 5.76,2.26 6.277,2.398 0.517,0.137 10 IG 4.246,2.13 5.096,2.267 0.850,0.137 10 ECU-IG No.2 5.508,3.851 5.868,3.990 0.360,0.138 10 H117 0.609,1.456 0.974,1.594 0.365,0.138 10 H119 1.877,0.533 1.986,0.676 0.109,0.142 10 7 1.877,0.977 2.051,1.120 0.174,0.143 10 18 5.508,4.005 6.838,4.320 1.331,0.314 10 Power Steering ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (POWER STEERING ECU BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (POWER STEERING ECU BRANCH WIRE)
a.
U154144E02
1.302,1.438 1.479,1.771 1.479,1.771 1.573,1.771 true 1.115,1.438 0.938,1.771 0.938,1.771 0.844,1.771 true 0.094,0.063 0.333,0.281 0.24,0.219 10 false *a 1.635,1.719 2.083,1.927 0.448,0.208 10 false CANL 0.417,1.677 0.865,1.885 0.448,0.208 10 false CANH 1.604,0.406 1.958,0.542 0.354,0.135 10 false H117

Disconnect the H117 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H117-1 (CANH) - H117-2 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE POWER STEERING ECU ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
U154145E02
1.802,1.458 1.969,1.792 1.969,1.792 2.052,1.792 true 1.458,1.458 1.292,1.792 1.292,1.792 1.208,1.792 true 0.083,0 0.323,0.219 0.24,0.219 10 false *a 2.104,1.719 2.552,1.927 0.448,0.208 10 false IG 0.865,1.698 1.313,1.906 0.448,0.208 10 false GND 1.604,0.406 1.979,0.573 0.375,0.167 10 false H117

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H117-5 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H117-3 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR