Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM27L0U _57 Power Source / Network _049335 NETWORKING _0235802 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Center Airbag Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Center Airbag Sensor Communication Stop Mode Either condition is met:
·

"Airbag" is not displayed on the "Bus Check" screen.

·

"Center Airbag Sensor Communication Stop Mode" in "DTC Communication Table" applies.


·

Power source or inside of center airbag sensor assembly

·

Center airbag sensor assembly CAN branch wire or connector

·

Center airbag sensor assembly



WIRING DIAGRAM

C245775E02
0.84,1.985 2.513,2.126 1.673,0.141 10 No. 1 Junction Connector 5.852,0.994 6.369,1.131 0.517,0.136 10 CANH 5.519,0.883 5.694,1.020 0.174,0.136 10 13 5.852,1.428 6.369,1.564 0.517,0.136 10 CANL 5.519,1.315 5.694,1.457 0.174,0.142 10 22 5.852,2.595 6.369,2.732 0.517,0.136 10 IG2 5.519,2.483 5.694,2.625 0.174,0.142 10 21 5.852,3.389 6.369,3.526 0.517,0.136 10 E1 5.519,3.277 5.694,3.419 0.174,0.142 10 25 5.852,4.044 6.369,4.181 0.517,0.136 10 E2 5.519,3.932 5.694,4.074 0.174,0.142 10 26 4.398,2.419 4.668,2.576 0.270,0.157 10 IGN 1.707,2.586 2.676,2.728 0.969,0.142 10 from IG2 Relay 5.556,4.944 6.911,5.271 1.356,0.327 10 Center Airbag Sensor Assembly 0.84,1.844 1.366,1.983 0.525,0.139 10 H119 1.958,0.868 2.091,1.045 0.132,0.177 10 1 1.958,1.32 2.174,1.497 0.216,0.177 10 12 5.556,4.796 6.073,4.946 0.517,0.150 10 H56

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (CENTER AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (CENTER AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE)
a.
U153693E02
2.031,1 2.5,0.417 2.5,0.417 2.583,0.417 true 2.135,1.271 2.49,1.677 2.49,1.677 2.573,1.677 true 0.427,1.01 0.698,1.156 0.271,0.146 10 false H56 2.646,0.333 3.083,0.51 0.438,0.177 10 false CANH 0.125,0.073 0.333,0.25 0.208,0.177 10 false *a 2.615,1.615 3.021,1.792 0.406,0.177 10 false CANL

Disconnect the H56 center airbag sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H56-13 (CANH) - H56-22 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Center Airbag Sensor Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (CENTER AIRBAG SENSOR ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CENTER AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (CENTER AIRBAG SENSOR ASSEMBLY - BATTERY AND BODY GROUND)
a.
U153694E02
2.26,1.219 2.438,1.021 2.438,1.021 2.531,1.021 true 1.792,1.25 2.146,1.667 2.146,1.667 2.24,1.667 true 1.667,1.25 1.979,1.917 1.979,1.917 2.063,1.917 true 0.427,1.01 0.698,1.156 0.271,0.146 10 false H56 2.604,0.938 3.042,1.115 0.438,0.177 10 false IG2 0.083,0.042 0.292,0.219 0.208,0.177 10 false *a 2.25,1.594 2.656,1.771 0.406,0.177 10 false E1 2.083,1.844 2.49,2.021 0.406,0.177 10 false E2

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H56-21 (IG2) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H56-25 (E1) - Body ground Always Below 1 Ω
H56-26 (E2) - Body ground Always Below 1 Ω



Text in Illustration
*a Rear view of wire harness connector
(to Center Airbag Sensor Assembly)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR