Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM27L0U _57 Power Source / Network _049335 NETWORKING _0235802 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Air Conditioning Amplifier Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Air Conditioning Amplifier Communication Stop Mode Either condition is met:
·

"Air Conditioning Amplifier" is not displayed on the "Bus Check" screen.

·

"Air Conditioning Amplifier Communication Stop Mode" in "DTC Communication Table" applies.


·

Power source or inside of air conditioning amplifier assembly

·

Air conditioning amplifier assembly CAN branch wire or connector

·

Air conditioning amplifier assembly



WIRING DIAGRAM

C245635E03
0.609,1.951 2.226,2.094 1.617,0.143 10 No. 2 Junction Connector 5.758,0.985 6.275,1.123 0.517,0.138 10 CANH 5.758,1.425 6.275,1.563 0.517,0.138 10 CANL 5.424,1.327 5.598,1.466 0.174,0.139 10 12 5.424,3.855 5.598,3.993 0.174,0.139 10 14 5.498,3.044 5.599,3.183 0.101,0.139 10 1 5.423,2.247 5.598,2.386 0.175,0.139 10 21 5.424,0.884 5.598,1.022 0.174,0.139 10 11 5.758,2.351 6.275,2.489 0.517,0.138 10 B 5.76,3.962 6.277,4.100 0.517,0.137 10 GND 4.551,2.182 4.810,2.322 0.259,0.140 10 A/C 2.059,2.343 2.857,2.484 0.799,0.141 10 from Battery 1.637,3.165 2.854,3.302 1.217,0.137 10 from IG No.1 Relay 5.76,3.157 6.277,3.294 0.517,0.137 10 IG+ 4.246,3.026 5.096,3.164 0.850,0.137 10 ECU-IG No.1 5.293,4.748 5.588,4.887 0.296,0.138 10 H24 0.609,1.807 0.974,1.945 0.365,0.138 10 H115 1.877,0.884 1.986,1.026 0.109,0.142 10 1 1.877,1.327 2.051,1.470 0.174,0.143 10 12 5.293,4.902 6.897,5.217 1.604,0.314 10 Air Conditioning Amplifier Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY CAN BRANCH WIRE)
a.
U153696E01
0.334,1.303 0.619,1.445 0.286,0.142 10 H24 0.68,1.842 1.069,1.984 0.390,0.142 10 CANL 2.353,1.842 2.765,1.984 0.413,0.142 10 CANH 0.052,0.046 0.338,0.188 0.286,0.142 10 *a 1.785,1.383 2.237,1.92 2.237,1.92 2.331,1.92 false 1.708,1.383 1.257,1.92 1.257,1.92 1.162,1.92 false

Disconnect the H24 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H24-11 (CANH) - H24-12 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)
a.
U153697E01
0.353,1.266 0.629,1.408 0.276,0.142 10 H24 0.662,0.775 1.002,0.917 0.339,0.142 10 GND 2.829,1.122 3.097,1.264 0.268,0.142 10 IG+ 2.819,1.58 2.933,1.722 0.114,0.142 10 B 0.052,0.046 0.338,0.188 0.286,0.142 10 *a 1.545,1.323 1.158,0.855 1.158,0.855 1.063,0.855 false 2.619,1.49 2.735,1.658 2.735,1.658 2.808,1.658 false 2.619,1.329 2.746,1.202 2.746,1.202 2.819,1.202 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H24-21 (B) - Body ground Always 11 to 14 V
H24-1 (IG+) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H24-14 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)


OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR