Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM27L0U _57 Power Source / Network _049335 NETWORKING _0235802 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U0104  Lost Communication with Driving Support ECU  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0104 There is no communication from the distance control ECU assembly.
·

Power source or inside of distance control ECU assembly

·

Distance control ECU assembly CAN branch wire or connector

·

Distance control ECU assembly



For vehicles with an dynamic laser cruise control system.


WIRING DIAGRAM

C242848E02
5.563,3.663 5.957,3.839 0.395,0.176 10 A43 5.563,3.822 6.947,4.130 1.385,0.308 10 Distance Control ECU Assembly 0.607,1.776 1.008,1.925 0.400,0.149 10 H116 0.607,1.935 2.262,2.076 1.655,0.141 10 No. 3 Junction Connector 5.814,0.957 6.280,1.097 0.466,0.141 10 CANH 1.929,0.839 2.107,0.993 0.178,0.154 10 11 5.602,0.855 5.711,1.009 0.109,0.154 10 8 5.612,1.295 5.711,1.449 0.100,0.154 10 9 4.414,2.163 5.258,2.301 0.844,0.138 10 ECU-IG No.2 2.343,2.309 3.675,2.446 1.332,0.137 10 from IG1 No.3 Relay 1.929,1.292 2.123,1.446 0.194,0.153 10 22 5.814,1.398 6.280,1.535 0.466,0.137 10 CANL 5.598,2.206 5.697,2.359 0.100,0.154 10 1 5.814,2.311 6.280,2.452 0.466,0.141 10 B 5.518,2.82 5.697,2.974 0.178,0.154 10 12 5.814,2.925 6.280,3.066 0.466,0.141 10 GND

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (DISTANCE CONTROL ECU ASSEMBLY CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (DISTANCE CONTROL ECU ASSEMBLY CAN BRANCH WIRE)
a.
U153822E01
2.728,1.115 2.995,1.254 0.267,0.139 10 A43 0.784,1.8 1.250,1.940 0.466,0.141 10 CANH 0.52,1.472 0.987,1.609 0.466,0.137 10 CANL 1.507,1.175 1.105,1.563 1.105,1.563 0.976,1.563 false 1.283,1.877 1.403,1.877 1.403,1.877 1.597,1.176 false 0.079,0.063 0.228,0.200 0.149,0.137 10 *a

Disconnect the A43 distance control ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A43-8 (CANH) - A43-9 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Distance Control ECU Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (DISTANCE CONTROL ECU ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE DISTANCE CONTROL ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (DISTANCE CONTROL ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
U153823E02
1.073,1.073 0.885,0.833 0.885,0.833 0.75,0.833 true 2.365,1.073 2.563,0.833 2.563,0.833 2.688,0.833 true 2.76,1.104 3.188,1.333 0.427,0.229 10 false A43 0.396,0.781 0.865,0.927 0.469,0.146 10 false GND 2.719,0.688 3.135,0.927 0.417,0.24 10 false B 0.083,0.042 0.323,0.26 0.24,0.219 10 false *a

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A43-1 (B) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A43-12 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Rear view of wire harness connector
(to Distance Control ECU Assembly)


OK

REPLACE DISTANCE CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR