Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM27L0U _57 Power Source / Network _049335 NETWORKING _0235802 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U0199  Lost Communication with "Door Control Module A"  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0199 There is no communication from the outer mirror control ECU assembly.
·

Power source or inside outer mirror control ECU assembly

·

Outer mirror control ECU assembly CAN branch wire or connector

·

Outer mirror control ECU assembly



For vehicles with an seat memory.


WIRING DIAGRAM

C245280E03
0.636,1.984 2.308,2.130 1.673,0.146 10 No. 3 Junction Connector 0.641,1.838 1.036,1.983 0.395,0.145 10 H116 1.925,0.894 2.058,1.071 0.132,0.177 10 5 1.92,1.346 2.101,1.523 0.181,0.177 10 16 5.837,2.829 6.354,2.966 0.517,0.137 10 B 5.837,3.491 6.155,3.628 0.318,0.136 10 ACC 5.483,1.448 5.695,1.585 0.212,0.136 10 M8 5.503,1.257 5.675,1.397 0.172,0.139 10 21 5.483,1.007 5.695,1.143 0.212,0.136 10 M8 5.542,0.816 5.637,0.955 0.096,0.139 10 1 5.483,2.831 5.695,2.967 0.212,0.136 10 M7 5.542,2.64 5.637,2.779 0.096,0.139 10 3 5.483,3.491 5.695,3.628 0.212,0.136 10 M7 5.542,3.301 5.637,3.440 0.096,0.139 10 4 5.483,4.15 5.695,4.286 0.212,0.136 10 M7 5.542,3.959 5.637,4.099 0.096,0.139 10 9 4.019,2.708 4.293,2.846 0.274,0.138 10 MIR 4,3.366 4.311,3.509 0.311,0.143 10 ACC 1.87,2.83 2.648,2.967 0.778,0.136 10 from Battery 1.598,3.489 2.646,3.630 1.048,0.141 10 from ACC Relay 5.837,4.147 6.354,4.286 0.517,0.139 10 GND 5.837,1.009 6.354,1.145 0.517,0.136 10 CAN 5.837,1.448 6.354,1.584 0.517,0.136 10 CGND 5.399,4.8 7.029,5.104 1.630,0.304 10 Outer Mirror Control ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistance of the CAN main wire or CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (OUTER MIRROR CONTROL ECU ASSEMBLY CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (OUTER MIRROR CONTROL ECU ASSEMBLY CAN BRANCH WIRE)
a.
U153877E01
0.518,1.474 0.613,2.061 0.613,2.061 0.722,2.061 false 0.897,1.806 0.819,1.806 0.819,1.806 0.509,1.325 false 0.069,0.041 0.252,0.193 0.184,0.151 10 *a 1.585,0.47 1.798,0.607 0.213,0.137 10 M8 0.917,1.729 1.236,1.866 0.319,0.137 10 CAN 0.731,1.984 1.166,2.121 0.435,0.137 10 CGND

Disconnect the M8 outer mirror control ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
M8-1 (CAN) - M8-21 (CGND) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CAN, CGND)

4.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
U153878E01
2.011,1.481 2.298,1.842 2.298,1.842 2.412,1.842 false 2.22,1.074 2.45,0.917 2.45,0.917 2.598,0.917 false 2.429,0.648 2.295,0.648 2.295,0.648 2.02,1.074 false 0.075,0.04 0.407,0.307 0.332,0.267 10 *a 1.59,0.514 1.804,0.653 0.214,0.139 10 M7 2.455,0.572 2.669,0.710 0.214,0.139 10 B 2.613,0.841 2.945,0.980 0.332,0.139 10 ACC 2.429,1.772 2.761,1.911 0.332,0.139 10 GND

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the M7 outer mirror control ECU assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M7-3 (B) - Body ground Always 11 to 14 V
M7-4 (ACC) - Body ground Ignition switch ACC 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M7-9 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly)


OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR