Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM27L0U _57 Power Source / Network _049335 NETWORKING _0235802 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U0232  Lost Communication with Blind Spot Monitor Slave Module  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0232 There is no communication from the blind spot monitor sensor LH.
·

Power source or inside of blind spot monitor sensor LH

·

Blind spot monitor sensor LH CAN branch wire or connector

·

Blind spot monitor sensor LH



For vehicles with an blind spot monitor sensor.


WIRING DIAGRAM

C242847E01
5.633,3.892 6.027,4.068 0.395,0.176 10 O46 5.633,4.051 6.860,4.359 1.227,0.308 10 Blind Spot Monitor Sensor LH 0.607,1.528 1.008,1.678 0.400,0.149 10 O47 0.607,1.688 2.262,1.828 1.655,0.141 10 No. 5 Junction Connector 5.814,0.709 6.280,0.850 0.466,0.141 10 CA1P 1.929,0.592 2.107,0.745 0.178,0.154 10 11 5.602,0.608 5.711,0.762 0.109,0.154 10 8 5.612,1.048 5.711,1.201 0.100,0.154 10 4 4.414,1.916 5.252,2.054 0.838,0.138 10 ECU-IG No.1 2.413,2.062 3.750,2.199 1.337,0.137 10 from IG No.1 Relay 1.929,1.045 2.123,1.198 0.194,0.153 10 22 5.814,1.151 6.280,1.288 0.466,0.137 10 CA1N 5.598,1.958 5.697,2.112 0.100,0.154 10 5 5.814,2.064 6.280,2.205 0.466,0.141 10 BLB 5.598,2.572 5.697,2.726 0.100,0.154 10 1 5.814,2.678 6.280,2.819 0.466,0.141 10 BLGD 5.598,3.187 5.697,3.340 0.100,0.154 10 3 5.814,3.292 6.280,3.433 0.466,0.141 10 LGND

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (BLIND SPOT MONITOR SENSOR LH CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (BLIND SPOT MONITOR SENSOR LH CAN BRANCH WIRE)
a.
U153818E01
2,1.333 2.302,1.688 2.302,1.688 2.438,1.688 true 2,1.167 2.281,0.813 2.281,0.813 2.406,0.813 true 0.063,0.052 0.323,0.188 0.26,0.135 10 false *a 2.49,1.625 2.958,1.865 0.469,0.24 10 false CA1P 2.458,0.74 2.958,0.969 0.5,0.229 10 false CA1N 0.573,1.208 0.896,1.406 0.323,0.198 10 false O46

Disconnect the O46 blind spot monitor sensor LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
O46-8 (CA1P) - O46-4 (CA1N) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)



OK

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE BLIND SPOT MONITOR SENSOR LH CAN BRANCH WIRE OR CONNECTOR (CA1P, CA1N)

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BATTERY AND BODY GROUND)
a.
U153819E01
1.841,1.167 2.118,0.813 2.118,0.813 2.249,0.813 false 0.065,0.055 0.327,0.193 0.262,0.139 10 *a 2.269,0.739 2.677,0.878 0.408,0.139 10 LGND 0.538,0.739 0.945,0.878 0.408,0.139 10 BLGD 0.619,1.603 1.027,1.741 0.408,0.139 10 BLB 2.569,1.202 2.850,1.340 0.281,0.139 10 O46 1.438,1.333 1.137,1.687 1.137,1.687 1.006,1.687 false 1.438,1.167 1.16,0.813 1.16,0.813 1.029,0.813 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
O46-5 (BLB) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O46-1 (BLGD) - Body ground Always Below 1 Ω
O46-3 (LGND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR