Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM27L0U _57 Power Source / Network _049335 NETWORKING _0235802 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U0233  Lost Communication with Blind Spot Monitor Master Module  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0233 There is no communication from the blind spot monitor sensor RH.
·

Power source or inside of blind spot monitor sensor RH

·

Blind spot monitor sensor RH CAN branch wire or connector

·

Blind spot monitor sensor RH



For vehicles with an blind spot monitor sensor.


WIRING DIAGRAM

C242848E01
5.609,3.663 6.004,3.839 0.395,0.176 10 P25 5.609,3.822 6.790,4.130 1.181,0.308 10 Blind Spot Monitor Sensor RH 0.607,1.776 1.008,1.925 0.400,0.149 10 O48 0.607,1.935 2.262,2.076 1.655,0.141 10 No. 6 Junction Connector 5.814,0.957 6.280,1.097 0.466,0.141 10 CA1P 1.929,0.839 2.107,0.993 0.178,0.154 10 10 5.602,0.855 5.711,1.009 0.109,0.154 10 8 5.612,1.295 5.711,1.449 0.100,0.154 10 4 4.414,2.163 5.254,2.301 0.841,0.138 10 ECU-IG No.1 2.415,2.309 3.745,2.446 1.330,0.137 10 from IG No.1 Relay 1.929,1.292 2.123,1.446 0.194,0.153 10 21 5.814,1.398 6.280,1.535 0.466,0.137 10 CA1N 5.598,2.206 5.697,2.359 0.100,0.154 10 5 5.814,2.311 6.280,2.452 0.466,0.141 10 BRB 5.598,2.82 5.697,2.974 0.100,0.154 10 1 5.814,2.925 6.280,3.066 0.466,0.141 10 BRGD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (BLIND SPOT MONITOR SENSOR RH CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (BLIND SPOT MONITOR SENSOR RH CAN BRANCH WIRE)
a.
U153820E01
0.065,0.055 0.327,0.193 0.262,0.139 10 *a 2.456,1.626 2.849,1.764 0.394,0.139 10 CA1P 2.433,0.739 2.826,0.878 0.394,0.139 10 CA1N 0.585,1.197 0.849,1.335 0.264,0.139 10 P25 2.003,1.333 2.303,1.687 2.303,1.687 2.434,1.687 false 2.003,1.167 2.28,0.813 2.28,0.813 2.411,0.813 false

Disconnect the P25 blind spot monitor sensor RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
P25-8 (CA1P) - P25-4 (CA1N) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)



OK

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE BLIND SPOT MONITOR SENSOR RH CAN BRANCH WIRE OR CONNECTOR (CA1P, CA1N)

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BATTERY AND BODY GROUND)
a.
U153821E01
0.065,0.055 0.327,0.193 0.262,0.139 10 *a 0.512,0.739 0.941,0.878 0.428,0.139 10 BRGD 0.619,1.603 1.027,1.741 0.408,0.139 10 BRB 1.438,1.333 1.137,1.687 1.137,1.687 1.006,1.687 false 1.438,1.167 1.16,0.813 1.16,0.813 1.029,0.813 false 2.613,1.189 2.877,1.327 0.264,0.139 10 P25

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
P25-5 (BRB) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P25-1 (BRGD) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR