Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM27L0U _57 Power Source / Network _049335 NETWORKING _0235803 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B1273  Sliding Roof ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the sliding roof drive gear sub-assembly and main body ECU stops for 10 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B1273 No communication between the sliding roof drive gear sub-assembly and main body ECU for 10 seconds or more.
·

Sliding roof drive gear sub-assembly

·

Main body ECU

·

Harness or connector



WIRING DIAGRAM

B173719E83
0.917,4.74 2.594,4.938 1.677,0.198 10 false : LIN Communication Line 0.594,3.896 1.448,4.094 0.854,0.198 10 false from Battery 1.823,4.083 2.385,4.24 0.563,0.156 10 false S/ROOF 3.417,4.333 3.646,4.51 0.229,0.177 10 false U3 3.281,3.75 3.479,3.927 0.198,0.177 10 false 10 3.354,2.99 3.51,3.167 0.156,0.177 10 false 3 3.313,1.146 3.5,1.323 0.188,0.177 10 false 10 3.563,3.104 4,3.281 0.438,0.177 10 false MPX1 3.563,1.26 4,1.438 0.438,0.177 10 false LIN2 4.458,3.104 4.594,3.281 0.135,0.177 10 false E 4.708,2.99 4.844,3.167 0.135,0.177 10 false 8 3.563,3.844 4,4.021 0.438,0.177 10 false B 3.427,4.49 5.844,4.667 2.417,0.177 10 false Sliding Roof Drive Gear Sub-assembly 3.49,1.906 3.76,2.083 0.271,0.177 10 false H2 3.5,2.052 5.375,2.292 1.875,0.24 10 false Main Body ECU

CAUTION / NOTICE / HINT

NOTICE:

When using the Techstream with the ignition switch off to troubleshoot:

Connect the Techstream to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.


HINT:

DTC B2325 is stored when the communication between the sliding roof ECU and main body ECU stops.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SLIDING ROOF ECU)
a.
U154030E02
2.24,1.75 2.698,1.583 true 2.25,3.781 2.75,3.5 true 0.563,1.49 0.76,1.667 0.198,0.177 10 false H2 0.542,3.865 0.74,4.042 0.198,0.177 10 false U3 0.281,0.094 2.646,0.49 2.365,0.396 10 false Front view of wire harness connector: (to Main Body ECU) 0.125,2.406 2.688,2.76 2.563,0.354 10 false Front view of wire harness connector: (to Sliding Roof Drive Gear Sub-Assembly) 2.75,1.469 3.063,1.646 0.313,0.177 10 false LIN2 2.802,3.427 3.198,3.604 0.396,0.177 10 false MPX1

Disconnect the H2 main body ECU connector.


b.

Disconnect the U3 sliding roof drive gear sub-assembly connector.

Measure the resistance and voltage according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
H2-10 (LIN2) - U3-3 (MPX1) Always Below 1 Ω
H2-10 (LIN2) or U3-3 (MPX1) - Body ground Always 10 kΩ or higher


Standard Voltage:
Tester Connection Condition Specified Condition
U3-3 (MPX1) - Body ground Always Below 1 V



c.

Reconnect the main body ECU connector.


d.

Reconnect the sliding roof drive gear sub-assembly connector.



OK

2.CHECK SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU - BATTERY AND BODY GROUND)
a.
U154031E02
2.438,1.552 2.792,1.635 true 2.042,1.552 1.948,1.854 true 0.563,1.333 0.76,1.51 0.198,0.177 10 false U3 0.083,0.052 2.615,0.458 2.531,0.406 10 false Front view of wire harness connector: (to Sliding Roof Drive Gear Sub-Assembly) 2.854,1.573 3.01,1.75 0.156,0.177 10 false B 1.885,1.865 2.042,2.042 0.156,0.177 10 false E

Disconnect the U3 sliding roof drive gear sub-assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
U3-8 (E) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
U3-10 (B) - Body ground Always 11 to 14 V



c.

Reconnect the sliding roof drive gear sub-assembly connector.



OK

3.REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY
a.

Temporarily replace the sliding roof drive gear sub-assembly with a new or normally functioning one (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF HOUSING>REMOVAL).




NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1273 is not output A
DTC B1273 is output B



A

END (SLIDING ROOF ECU IS DEFECTIVE)

B

REPLACE MAIN BODY ECU