Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM27L0U _57 Power Source / Network _049335 NETWORKING _0235803 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B1287  Back Door ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the back door ECU and main body ECU stops for 10 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B1287 No communication between the back door ECU and main body ECU for 10 seconds or more.
·

Back door ECU

·

Main body ECU

·

Harness or connector



WIRING DIAGRAM

E160675E02
3.316,1.165 3.487,1.347 0.171,0.181 10 10 3.577,1.285 3.888,1.467 0.310,0.181 10 LIN2 3.316,3.006 3.487,3.187 0.171,0.181 10 16 4.66,3.006 4.816,3.187 0.156,0.181 10 6 3.577,3.126 3.972,3.307 0.395,0.181 10 MPX1 4.241,3.126 4.567,3.307 0.326,0.181 10 GND 3.346,3.669 3.502,3.850 0.156,0.181 10 7 3.577,3.789 3.980,3.970 0.403,0.181 10 BECU 3.346,4.292 3.502,4.473 0.156,0.181 10 1 3.577,4.412 3.888,4.593 0.310,0.181 10 BDR 3.496,1.886 3.690,2.067 0.195,0.181 10 H2 3.496,2.027 4.501,2.208 1.005,0.181 10 Main Body ECU 3.496,4.827 3.683,5.009 0.187,0.181 10 V2 3.496,4.969 4.493,5.150 0.997,0.181 10 Back Door ECU 1.799,3.936 2.326,4.117 0.526,0.181 10 ECU-B1 0.41,3.824 1.184,4.006 0.773,0.181 10 from Battery 1.669,4.545 2.688,4.726 1.019,0.181 10 POWER No. 5 0.992,5.154 2.708,5.335 1.716,0.181 10 : LIN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

When using the Techstream with the ignition switch off to troubleshoot:

Connect the Techstream to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.


HINT:

DTC B2325 is stored when the communication between the back door ECU and main body ECU stops.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BACK DOOR ECU)
a.
U154038E02
2.219,1.656 2.677,1.49 true 2.375,3.979 2.719,4.073 true 0.552,1.375 0.75,1.552 0.198,0.177 10 false H2 0.229,0.094 2.594,0.49 2.365,0.396 10 false Front view of wire harness connector: (to Main Body ECU) 2.75,1.375 3.063,1.552 0.313,0.177 10 false LIN2 0.625,3.75 0.813,3.927 0.188,0.177 10 false V2 0.24,2.438 2.677,2.792 2.438,0.354 10 false Front view of wire harness connector: (to Back Door ECU) 2.802,4.031 3.198,4.208 0.396,0.177 10 false MPX1

Disconnect the H2 main body ECU connector.


b.

Disconnect the V2 back door ECU connector.


c.

Measure the resistance and voltage according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
H2-10 (LIN2) - V2-16 (MPX1) Always Below 1 Ω
H2-10 (LIN2) or V2-16 (MPX1) - Body ground Always 10 kΩ or higher


Standard Voltage:
Tester Connection Condition Specified Condition
V2-16 (MPX1) - Body ground Always Below 1 V



d.

Reconnect the main body ECU connector.


e.

Reconnect the back door ECU connector.



OK

2.CHECK BACK DOOR ECU (BACK DOOR ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK BACK DOOR ECU (BACK DOOR ECU - BATTERY AND BODY GROUND)
a.
U154039E02
0.844,1.063 1.26,1.281 true 0.677,1.802 1.198,1.531 true 2.625,1.073 2.208,1.281 true 0.313,1.396 0.5,1.573 0.188,0.177 10 false V2 0.135,0.021 2.479,0.438 2.344,0.417 10 false Front view of wire harness connector: (to Back Door ECU) 0.438,0.979 0.75,1.156 0.313,0.177 10 false BDR 0.167,1.719 0.573,1.896 0.406,0.177 10 false BECU 2.667,0.979 2.99,1.156 0.323,0.177 10 false GND

Disconnect the V2 back door ECU connector.


b.

Measure the resistance and voltage according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
V2-6 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
V2-1 (BDR) - Body ground Always 11 to 14 V
V2-7 (BECU) - Body ground



c.

Reconnect the back door ECU connector.



OK

3.REPLACE BACK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE BACK DOOR ECU
a.

Temporarily replace the back door ECU with a new or normally functioning one (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR>DISASSEMBLY).




NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1287 is not output A
DTC B1287 is output B



A

END (BACK DOOR ECU IS DEFECTIVE)

B

REPLACE MAIN BODY ECU