Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR
RM27L0U _59 Vehicle Exterior _049349 DOOR / HATCH _0235960 BACK DOOR A

DOOR / HATCH  BACK DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 85475 3.REMOVE POWER BACK DOOR ROD (w/ Power Back Door)

a.
B194506E03
1.438,1.875 0.969,1.583 true 1.5,1.802 2.479,2.104 0.979,0.302 10 true Protective Tape

Using a screwdriver with its tip wrapped in protective tape, remove the 2 stop rings and power back door rod.


Hide 67939B 4.REMOVE BACK DOOR CENTER GARNISH

a.
B190514

Disengage the 4 clips and the claw and remove the back door center garnish.


Hide 67937B 5.REMOVE BACK DOOR SIDE GARNISH RH

a.
B190515

Disengage the 2 clips and remove the back door side garnish RH.


Hide 67938A 6.REMOVE BACK DOOR SIDE GARNISH LH

a.
B190516

Disengage the 3 clips and remove the back door side garnish LH


Hide 68957B 7.REMOVE BACK DOOR STAY LOWER BRACKET (w/ Power Back Door)

a.
B194233

Remove the 2 bolts and remove the back door stay lower bracket.


Hide 67963A 8.REMOVE BACK DOOR STRAP COVER

a.
B190517

Slide the back door strap cover and disengage the claw and remove the back door strap cover.


Hide 67961 9.REMOVE BACK DOOR PULL STRAP

a.
B190519

Remove the bolt and remove the back door pull strap.


Hide 67750 10.REMOVE BACK DOOR TRIM BOARD ASSEMBLY

a.
B443320

Disengage the 11 clips and remove the back door trim board assembly.


Hide 68291 11.REMOVE BACK DOOR GLASS WEATHERSTRIP

a.
B190511

Raise the 9 claws of the rear back door glass weatherstrip and then remove the back door glass weatherstrip from the back door trim board assembly, as shown in the illustration.


Hide 67847A 12.REMOVE BACK DOOR SERVICE HOLE COVER

a.
B190521

Remove the back door service hole cover.

NOTICE:

Remove any tape remaining on the door.



Hide 89747C 13.REMOVE POWER BACK DOOR WARNING BUZZER (w/ Power Back Door)

Hide 89221 14.REMOVE MULTIPLEX NETWORK BODY ECU (w/ Power Back Door)

a.
B194490

Disconnect the 2 connectors and disengage the 2 clamps.


b.

Remove the 2 screws and remove the multiplex network body ECU.


Hide 67848C 15.REMOVE BACK DOOR NO. 2 SERVICE HOLE COVER

a.
B190525

Remove the 3 screws and disengage the 2 clips and remove the back door No. 2 service hole cover.


Hide 85292A 18.REMOVE REAR WIPER ARM HEAD CAP

Hide 19.REMOVE REAR WIPER ARM AND BLADE ASSEMBLY

Hide 85110R 20.REMOVE REAR WIPER MOTOR ASSEMBLY

Hide 85143R 21.REMOVE REAR WIPER MOTOR GROMMET

Hide 85293A 22.REMOVE REAR WIPER STOPPER

a.
B190526

Disengage the claw and guide and remove the linear wiper step RH


Hide 75816 23.REMOVE BACK DOOR OUTSIDE MOULDING LH

Hide 75815 24.REMOVE BACK DOOR OUTSIDE MOULDING RH

Hide 68290A 25.REMOVE BACK DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

Hide 68275 26.REMOVE BACK DOOR GLASS RUN

a.
B190527

Remove the back door glass run.


Hide 68131 27.REMOVE BACK DOOR GLASS

a.
B190513

Remove the hole plig.


b.

Provisionally install the multiplex network body ECU.


c.
B190528

Move the back door glass until the 4 bolts can be seen through the service holes.


d.

Disconnect the 2 connectors.


e.

Remove the 4 bolts and remove the back door glass.

NOTICE:

Do not drop or damage the back door glass.



f.

Remove the multiplex network body ECU.


Hide 69850D 28.REMOVE BACK DOOR POWER WINDOW REGULATOR ASSEMBLY

a.
B190529E01
2.048,1.084 2.169,1.242 0.122,0.158 10 A

Disconnect the connector.


b.

Loosen nut A.


c.

Remove the 5 nuts, then remove the back door power window regulator assembly.

NOTICE:

Do not drop or damage the back door power window regulator assembly when removing the nuts.



Hide 69055B 29.REMOVE BACK DOOR LOCK CYLINDER

a.
B190530

Disconnect the connector


b.

Remove the 2 nuts and remove the back door lock cylinder.


Hide 69211C 33.REMOVE BACK DOOR OUTSIDE HANDLE

Hide 69308 34.REMOVE BACK DOOR LOCK PROTECTOR

a.
B190533

Disengage the 2 claws and back door lock protector sub-assembly.


Hide 69110A 35.REMOVE BACK DOOR LOCK (w/o Power Back Door)

Hide 69110A 36.REMOVE BACK DOOR LOCK (w/ Power Back Door)

Hide 81580D 37.REMOVE REAR LIGHT ASSEMBLY RH

Hide 81590A 38.REMOVE REAR LIGHT ASSEMBLY LH