Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM27L0U _57 Power Source / Network _049335 NETWORKING _0235803 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2321  Driver Side Door ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the front power window regulator motor assembly LH and main body ECU stops for 10 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B2321 No communication between the front power window regulator motor assembly LH and main body ECU for 10 seconds or more.
·

Front power window regulator motor assembly LH

·

Main body ECU

·

Harness or connector



WIRING DIAGRAM

E160670E02
5.057,1.279 5.367,1.460 0.310,0.181 10 LIN2 4.966,1.878 5.160,2.060 0.195,0.181 10 H2 4.966,2.017 5.971,2.199 1.005,0.181 10 Main Body ECU 4.775,1.173 4.947,1.354 0.171,0.181 10 10 2.507,1.279 2.817,1.460 0.310,0.181 10 LIN1 1.847,1.279 2.158,1.460 0.310,0.181 10 LIN2 1.757,1.879 1.967,2.060 0.210,0.181 10 M2 2.932,1.159 3.088,1.340 0.156,0.181 10 6 1.599,1.159 1.754,1.340 0.156,0.181 10 7 3.575,3.12 3.808,3.301 0.233,0.181 10 LIN 4.248,3.12 4.574,3.301 0.326,0.181 10 GND 3.34,3.014 3.496,3.195 0.156,0.181 10 9 3.552,3.864 3.707,4.046 0.156,0.181 10 B 3.496,4.292 3.706,4.473 0.210,0.181 10 M3 3.34,3.758 3.496,3.940 0.156,0.181 10 2 0.595,3.854 1.368,4.035 0.773,0.181 10 from Battery 1.6,4.003 2.575,4.184 0.974,0.181 10 POWER No. 3 0.995,4.707 2.741,4.888 1.746,0.181 10 : LIN Communication Line 4.663,3.014 4.819,3.195 0.156,0.181 10 1 1.758,2.05 3.511,2.395 1.753,0.345 10 Power Window Regulator Master Switch Assembly 3.496,4.469 5.533,4.825 2.037,0.356 10 Front Power Window Regulator Motor Assembly LH

CAUTION / NOTICE / HINT

NOTICE:

When using the Techstream with the ignition switch off to troubleshoot:

Connect the Techstream to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.


HINT:
·

DTC B2325 is stored when the communication between the front power window regulator motor assembly LH and main body ECU stops.

·

When DTC B1206 and B2321 are output simultaneously, perform the troubleshooting for DTC B1206 first (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>B1206).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - REGULATOR MOTOR LH)
a.
U154032E01
0.514,1.406 0.709,1.587 0.195,0.181 10 H2 0.514,3.808 0.724,3.990 0.210,0.181 10 M3 0.264,0.07 2.630,0.467 2.367,0.397 10 Front view of wire harness connector: (to Main Body ECU) 0.128,2.206 2.688,2.725 2.560,0.519 10 Front view of wire harness connector: (to Front Power Window Regulator Motor Assembly LH) 2.772,1.421 3.082,1.602 0.310,0.181 10 LIN2 2.268,1.693 2.734,1.53 false 2.802,3.98 3.036,4.161 0.233,0.181 10 LIN 2.038,4.308 2.764,4.065 false

Disconnect the H2 main body ECU connector.


b.

Disconnect the M3 front power window regulator motor assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H2-10 (LIN2) - M3-9 (LIN) Always Below 1 Ω



d.

Reconnect the main body ECU connector.


e.

Reconnect the front power window regulator motor assembly LH connector.



OK

2.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (REGULATOR MOTOR LH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (REGULATOR MOTOR LH - BATTERY AND BODY GROUND)
a.
U154034E02
2.073,2.313 2.802,2.073 true 1.708,2.302 0.979,2.063 true 0.625,2.615 0.833,2.792 0.208,0.177 10 false M3 0.177,0.177 2.521,0.698 2.344,0.521 10 false Front view of wire harness connector: (to Front Power Window Regulator Motor Assembly LH) 2.854,1.99 3.01,2.167 0.156,0.177 10 false B 0.646,1.969 0.969,2.146 0.323,0.177 10 false GND

Disconnect the M3 front power window regulator motor assembly LH connector.


b.

Measure the resistance and voltage according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
M3-1 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
M3-2 (B) - Body ground Always 11 to 14 V



c.

Reconnect the front power window regulator motor assembly LH connector.



OK

3.REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
a.

Temporarily replace the front power window regulator motor assembly LH with a new or normally functioning one (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR>REMOVAL).




NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2321 is not output A
DTC B2321 is output B



A

END (FRONT POWER WINDOW REGULATOR MOTOR LH IS DEFECTIVE)

B

REPLACE MAIN BODY ECU