Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM27L0U _58 Vehicle Interior _049337 THEFT DETERRENT / KEYLESS ENTRY _0235816 THEFT DETERRENT SYSTEM U

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  TERMINALS OF ECU  


CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)


U153563E06
2.917,1.167 2.833,1.167 2.833,1.167 2.417,1.427 false 5.531,0.688 5.438,0.688 5.438,0.688 5.031,0.938 false 2.927,1.729 2.854,1.729 2.854,1.729 2.448,1.885 false 2.948,2.656 2.865,2.656 2.865,2.656 2.448,2.406 false 2.917,2.26 2.844,2.26 2.844,2.26 2.438,2.156 false 2.229,2.833 2.458,3 0.229,0.167 10 false DA 1.958,2.094 2.167,2.26 0.208,0.167 10 false DB 1.958,1.26 2.208,1.427 0.25,0.167 10 false DC 4.927,1.708 5.146,1.875 0.219,0.167 10 false DD 5.573,0.604 5.781,0.771 0.208,0.167 10 false DE 3.031,2.552 3.25,2.719 0.219,0.167 10 false H1 3,2.167 3.219,2.333 0.219,0.167 10 false H2 3,1.635 3.219,1.802 0.219,0.167 10 false H3 2.979,1.094 3.198,1.26 0.219,0.167 10 false H4 3.094,3.635 3.302,3.771 0.208,0.135 10 false DB 1.542,5.135 1.76,5.281 0.219,0.146 10 false DD 4.396,5.125 4.604,5.271 0.208,0.146 10 false DE 1.073,3.635 1.281,3.781 0.208,0.146 10 false DA 5.646,3.625 5.875,3.771 0.229,0.146 10 false DC 6.01,6.958 6.208,7.115 0.198,0.156 10 false H4 3.521,6.969 3.719,7.115 0.198,0.146 10 false H3 1.083,6.969 1.292,7.115 0.208,0.146 10 false H2 6.104,5.125 6.302,5.26 0.198,0.135 10 false H1

a.

Disconnect the H1, H3, H4, DA, DB, DC and DD ECU connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
DB-13 (BECU) - Body ground GR - Body ground +B power source Always 11 to 14 V
DA-1 (ALTB) - Body ground B - Body ground +B power source Always 11 to 14 V
DD-62 (GND1, GND2) - Body ground W-B - Body ground Power ground Always Below 1 Ω
H4-24 (DCTY) - Body ground BR - Body ground Driver door courtesy switch Driver door CLOSED → OPEN 10 kΩ or higher → Below 1 Ω
H3-21 (PCTY) - Body ground BE - Body ground Front passenger door courtesy switch input Front passenger door CLOSED → OPEN 10 kΩ or higher → Below 1 Ω
DC-2 (LCTY) - Body ground G*1 - Body ground
B*2 - Body ground
Rear left door courtesy switch input Rear left door CLOSED → OPEN 10 kΩ or higher → Below 1 Ω
H3-25 (RRCY) - Body ground L - Body ground Rear right door courtesy switch input Rear right door CLOSED → OPEN 10 kΩ or higher → Below 1 Ω
H4-16 (HCTY) - Body ground V - Body ground Engine hood courtesy switch Engine hood CLOSED → OPEN 10 kΩ or higher → Below 1 Ω
H1-5 (KSW) - Body ground LG - Body ground Key unlock warning switch signal No key is in ignition key cylinder 10 kΩ or higher
Key is in ignition key cylinder Below 1 Ω

*1: w/ Power Seat (Rear No. 2)

*2: w/o Power Seat (Rear No. 2)

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the H1, H3, H4, DA, DB, DC and DD ECU connectors.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H1-4 (IND) - Body ground P - Body ground Security indicator signal Security indicator illuminates
(illuminates only for 60 sec. in alarm sounding state (it is blinking when system is in armed state))
3 to 5 V
H1-6 (SH) - Body ground W - Body ground Security horn signal Armed state Below 1 V
Security horn is sounding
(theft deterrent system is in alarm sounding state)
Pulse generation
H2-4 (HAZ) - Body ground BE - Body ground Hazard warning light signal Armed state Below 1 V
Security horn is sounding
(theft deterrent system is in alarm sounding state)
Pulse generation
H4-17 (GBS)* - Body ground L - Body ground Glass breakage sensor ECU signal Armed state Below 1 V
Glass breakage sensor ECU signal system is in alarm sounding state Pulse generation
DB-1 (HORN) - Body ground V - Body ground Horn signal
(low pitched and high pitched)
Armed state Below 1 V
Horn is sounding 11 to 14 V

*: w/ Glass Breakage Sensor

If the result is not as specified, the ECU may have a malfunction.



CHECK BACK DOOR ECU


U153311E04
2.281,0.427 2.542,0.573 0.26,0.146 10 false V2 3.729,0.427 3.948,0.573 0.219,0.146 10 false V3

a.

Disconnect the V2 and V3 connectors.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V2-1 (BDR) - Body ground SB - Body ground BDR power supply Always 11 to 14 V
V2-7 (BECU) - Body ground GR - Body ground BECU power supply Always 11 to 14 V
V3-10 (BDCY) - V3-20 (CTYE) P - R Back door courtesy switch circuit Back door is open 10 kΩ or higher
V3-10 (BDCY) - V3-20 (CTYE) P - R Back door courtesy switch circuit Back door is closed Below 1 Ω
V3-15 (HSW+) - V3-24 (HSW-) B - W Back door opener switch signal circuit Back door opener switch OFF 10 kΩ or higher
V3-15 (HSW+) - V3-24 (HSW-) B - W Back door opener switch signal circuit Back door opener switch ON Below 1 Ω
V2-6 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.