Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM27L0U _58 Vehicle Interior _049337 THEFT DETERRENT / KEYLESS ENTRY _0235816 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Security Indicator Light Circuit  


DESCRIPTION

When the theft deterrent system is in the disarmed state, the security indicator will flash continuously if the immobiliser system is set, or not illuminate if the immobiliser system is not set.

When the theft deterrent system is in the armed state, the immobiliser system is automatically set and the security indicator will flash continuously.

When the theft deterrent system is in the arming preparation state and alarm sounding state, the main body ECU causes the security indicator to be illuminated.

WIRING DIAGRAM

B154241E17
2.448,0.594 2.635,0.792 0.188,0.198 10 false 12 2.656,1.563 4.406,1.729 1.75,0.167 10 false Accessory Meter Assembly 2.646,1.74 3.875,1.906 1.229,0.167 10 false (Security Indicator) 2.646,1.406 2.948,1.573 0.302,0.167 10 false I22 5.875,3.177 6.177,3.344 0.302,0.167 10 false H1 2.719,0.708 2.854,0.906 0.135,0.198 10 false E 3.417,0.729 3.885,0.927 0.469,0.198 10 false MHTR 5.865,3.344 6.948,3.542 1.083,0.198 10 false Main Body ECU 5.969,0.708 6.292,0.906 0.323,0.198 10 false IND 3.906,0.594 4.167,0.792 0.26,0.198 10 false 16 5.771,0.594 5.927,0.792 0.156,0.198 10 false 4

PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM
a.

Connect a Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream main switch on.


d.

Select the item below in the Active Test and then check that the indicator operates.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Security Indicator Security indicator ON/OFF -

OK:

The security indicator light flashes or goes off correctly when operating it through the Techstream.




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR - MAIN BODY ECU)
2.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR - MAIN BODY ECU)
a.

Disconnect the H1 maim body ECU connector.

B443501E01
0.854,1.573 1.156,1.74 0.302,0.167 4.104,1.583 4.406,1.75 0.302,0.167 1.417,2.417 1.688,1.833 false 4.823,2.417 5.094,1.833 false 0.646,0.042 2.948,0.406 2.302,0.365 10 false Front view of wire harness connector: (to Main Body ECU) 4.292,0.021 6.594,0.385 2.302,0.365 10 false Front view of wire harness connector: (to Accessory Meter) 0.927,1.573 1.24,1.771 0.313,0.198 10 false H1 4.167,1.583 4.479,1.781 0.313,0.198 10 false I22 1.25,2.438 1.563,2.635 0.313,0.198 10 false IND 4.615,2.458 5.021,2.635 0.406,0.177 10 false MHTR


b.

Disconnect the I22 accessory meter connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H1-4 (IND) - I22-16 (MHTR) Always Below 1 Ω
H1-4 (IND) - Body ground Always 10 kΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR - BODY GROUND)
a.

Disconnect the I22 accessory meter connector.


b.
U153995E02
2.427,1.229 2.74,1.146 false 0.073,0.042 2.417,0.385 2.344,0.344 10 false Front view of wire harness connector: (to Accessory Meter) 2.781,1.042 2.906,1.188 0.125,0.146 10 false E 0.365,1.219 0.635,1.375 0.271,0.156 10 false I22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I22-12 (E) - Body ground Always Below 1 Ω




OK

4.INSPECT ACCESSORY METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT ACCESSORY METER ASSEMBLY
a.
E146077E05
0.324,0.076 2.628,0.445 2.304,0.369 10 Component with harness connected: (Accessory Meter Assembly) 0.18,2.167 0.322,2.323 0.142,0.156 10 E 2.037,2.983 2.526,3.139 0.489,0.156 10 MHTR 0.868,2.244 0.361,2.244 false 2.105,2.442 2.105,2.949 false

Reconnect the I22 accessory meter connector with the H1 main body ECU connector still disconnected.


b.

Apply battery voltage from the wire harness back side between the specified terminals of the indicator, and check the lighting condition of the security indicator.

OK :
Measurement Condition Specified Condition
Battery positive (+) → Terminal I22-16 (MHTR)
Battery negative (-) → Terminal I22-12 (E)
Security indicator comes on


NOTICE:
·

If the positive (+) lead and the negative (-) lead are incorrectly connected, the security indicator will not come on.

·

Voltage of more than 12 V will damage the security indicator.

·

If the voltage is too low, the security indicator will not come on.





OK

REPLACE MAIN BODY ECU

NG

REPLACE ACCESSORY METER ASSEMBLY