Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM27L0U _58 Vehicle Interior _049337 THEFT DETERRENT / KEYLESS ENTRY _0235816 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Glass Breakage Sensor ECU Circuit  


DESCRIPTION

When the glass breakage sensor detects the glass is broken (1st time), the sensor will set off an alarm for 20 seconds (pre-alarm). If the glass breakage sensor detects that more glass is broken (2nd time or more), the sensor will set off an alarm for 60 seconds.

WIRING DIAGRAM

B193809E04
1.219,0.771 1.583,0.948 0.365,0.177 10 false MIC+ 5.823,1.094 6.885,1.271 1.063,0.177 10 false Main Body ECU 3.052,4.094 4.906,4.438 1.854,0.344 10 false H64 Glass Breakage Sensor ECU 0.552,1.792 2.229,2.385 1.677,0.594 10 false H65 Glass Breakage Sensor Microphone 5.406,0.792 5.74,0.969 0.333,0.177 10 false GBS 5.094,0.604 5.281,0.781 0.188,0.177 10 false 17 6.167,2.333 6.594,2.51 0.427,0.177 10 false BECU 5.896,2.219 6.083,2.396 0.188,0.177 10 false 26 1.688,0.635 1.813,0.813 0.125,0.177 10 false 3 1.219,1.49 1.583,1.667 0.365,0.177 10 false MIC- 3.25,0.781 3.51,0.958 0.26,0.177 10 false MI+ 2.146,1.615 2.76,1.792 0.615,0.177 10 false Shielded 1.854,2.969 2.75,3.146 0.896,0.177 10 false ECU-IG No. 1 4.583,3.302 5.167,3.479 0.583,0.177 10 false ECU-B1 0.083,2.792 1.49,3 1.406,0.208 10 false from IG1 No. 1 Relay 5.177,3.833 6.042,4.01 0.865,0.177 10 false from Battery 3.25,1.49 3.51,1.667 0.26,0.177 10 false MI- 1.688,1.354 1.813,1.531 0.125,0.177 10 false 4 3.073,0.656 3.198,0.833 0.125,0.177 10 false 8 3.073,1.375 3.198,1.552 0.125,0.177 10 false 7 3.25,2.813 3.75,2.99 0.5,0.177 10 false GBIG 3.656,2.344 4.052,2.521 0.396,0.177 10 false GB+B 3.073,2.698 3.198,2.875 0.125,0.177 10 false 3 4.156,2.198 4.281,2.375 0.125,0.177 10 false 2 3.677,0.792 4.073,0.969 0.396,0.177 10 false GBSI 4.156,0.656 4.281,0.833 0.125,0.177 10 false 5 3.25,3.542 3.594,3.719 0.344,0.177 10 false GND 3.073,3.427 3.198,3.604 0.125,0.177 10 false 6 5.083,0.792 5.313,0.969 0.229,0.177 10 false H4 5.417,2.615 5.604,2.792 0.188,0.177 10 false 13 5.396,2.813 5.625,2.99 0.229,0.177 10 false DB 5.417,2.146 5.604,2.323 0.188,0.177 10 false 14 5.396,2.344 5.625,2.521 0.229,0.177 10 false DD 5.354,3.094 6.49,3.458 1.135,0.365 10 false Coel Side Junction Block LH

PROCEDURE

1.READ VALUE USING TECHSTREAM (GLASS BREAKAGE SENSOR)
a.

Using the Techstream, read the Data List.

MAIN BODY
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Glass Break Sensor Detection Glass breakage sensor detection /
ON or OFF
ON: Glass breakage sensor ON
OFF: Glass breakage sensor OFF
-

OK:

When tapping on the door glass with your finger, "ON" is displayed on the Techstream screen.




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT FUSE (ECU-IG No. 1)
2.INSPECT FUSE (ECU-IG No. 1)
a.
B188612E10
2.417,1.031 2.469,1.229 0.052,0.198 2.417,1.229 2.188,1.708 false 0.083,0.042 1.198,0.219 1.115,0.177 10 false Main Body ECU: 1.354,1.74 2.26,1.896 0.906,0.156 10 false ECU-IG No. 1

Remove the ECU-IG No. 1 fuse from the main body ECU.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ECU-IG No. 1 fuse Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (GLASS BREAKAGE SENSOR ECU - BATTERY AND BODY GROUND)

NG

REPLACE FUSE

3.CHECK HARNESS AND CONNECTOR (GLASS BREAKAGE SENSOR ECU - BATTERY AND BODY GROUND)
a.
U153185E02
2.281,2.125 2.677,2.781 false 1.688,2.125 1.729,2.781 false 1.427,2.125 0.906,2.781 false 0.073,0.042 2.396,0.385 2.323,0.344 10 false Front view of wire harness connector: (to Glass Breakage Sensor ECU) 0.365,1.646 0.708,1.823 0.344,0.177 10 false H64 1.563,2.833 1.927,3.01 0.365,0.177 10 false GBIG 0.469,2.823 0.865,3 0.396,0.177 10 false GB+B 2.625,2.823 2.948,3 0.323,0.177 10 false GND

Disconnect the H64 glass breakage sensor ECU connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H64-2 (GB+B) - H64-6 (GND) Always 11 to 14 V
H64-3 (GBIG) - H64-6 (GND) Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


Standard Resistance:
Tester Connection Condition Specified Condition
H64-6 (GND) - Body ground Always Below 1 Ω




OK

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - GLASS BREAKAGE SENSOR ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - GLASS BREAKAGE SENSOR ECU)
a.

Disconnect the H4 main body ECU connector.

B443063E02
3.667,1.448 3.979,1.625 0.313,0.177 0.531,1.438 0.844,1.615 0.313,0.177 5.49,2.115 5.177,1.75 false 2.792,2.156 2.479,1.792 false 0.302,0.042 2.573,0.438 2.271,0.396 10 false Front view of wire harness connector: (to Main Body ECU) 3.969,0.052 6.24,0.448 2.271,0.396 10 false Front view of wire harness connector: (to Glass Breakage Sensor ECU) 0.615,1.438 0.958,1.635 0.344,0.198 10 false H4 3.708,1.448 4.052,1.646 0.344,0.198 10 false H64 5.521,2.125 5.958,2.302 0.438,0.177 10 false GBSI 2.813,2.146 3.25,2.323 0.438,0.177 10 false GBS


b.

Disconnect the H64 glass breakage sensor ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H4-17 (GBS) - H64-5 (GBSI) Always Below 1 Ω
H4-17 (GBS) or H64-5 (GBSI) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (GLASS BREAKAGE SENSOR ECU - GLASS BREAKAGE SENSOR MICROPHONE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (GLASS BREAKAGE SENSOR ECU - GLASS BREAKAGE SENSOR MICROPHONE)
a.

Disconnect the H64 glass breakage sensor ECU connector.

B443064E02
4.271,1.479 4.615,1.719 0.344,0.24 0.563,1.521 0.906,1.76 0.344,0.24 2.031,2.292 2.26,1.854 false 2.604,2.271 2.479,1.865 false 5.917,2.188 5.708,1.771 false 5.323,2.177 5.458,1.792 false 0.719,0.156 3.115,0.531 2.396,0.375 10 false Front view of wire harness connector: (to Glass Breakage Sensor ECU) 4.094,0.156 6.521,0.583 2.427,0.427 10 false Front view of wire harness connector: (to Glass Breakage Sensor Microphone) 1.917,2.302 2.188,2.51 0.271,0.208 10 false MI- 0.625,1.542 0.896,1.75 0.271,0.208 10 false H64 2.594,2.292 2.865,2.5 0.271,0.208 10 false MI+ 5.198,2.198 5.563,2.385 0.365,0.188 10 false MIC+ 5.885,2.208 6.25,2.396 0.365,0.188 10 false MIC- 4.323,1.51 4.594,1.719 0.271,0.208 10 false H65


b.

Disconnect the H65 glass breakage sensor microphone connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H64-8 (MI+) - H65-3 (MIC+) Always Below 1 Ω
H64-7 (MI-) - H65-4 (MIC-)
H64-8 (MI+) or H65-3 (MIC+)- Body ground Always 10 kΩ or higher




OK

6.CHECK GLASS BREAKAGE SENSOR ECU (GLASS BREAKAGE SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK GLASS BREAKAGE SENSOR ECU (GLASS BREAKAGE SENSOR OUTPUT)
a.

Reconnect the H64 glass breakage sensor ECU connector.

B443065E02
0.417,1.479 0.75,1.677 0.333,0.198 2.292,2.198 1.969,1.688 false 0.156,0.063 2.667,0.448 2.51,0.385 10 false Component with harness connected: (Glass Breakage Sensor ECU) 0.479,1.5 0.76,1.677 0.281,0.177 10 false H64 2.323,2.198 2.771,2.375 0.448,0.177 10 false GBSI 6.375,1.281 6.823,1.458 0.448,0.177 10 false GND 6.365,1.958 6.813,2.135 0.448,0.177 10 false GND


b.

Reconnect the H65 glass breakage sensor microphone connector.


c.

Reconnect the H4 main body ECU connector.


d.

Turn the ignition switch to ON.


e.

Using an oscilloscope, check the waveform.

Standard:
Test Connector Tool Setting Vehicle Condition Specified Condition
H64-5 (GBSI) - Body ground 1 V/DIV., 50 msec./DIV. Ignition switch ON.
Tap the door glass with a hard object such as your fingernail.
Pulse generation




OK

NG

REPLACE GLASS BREAKAGE SENSOR MICROPHONE