Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM
RM27L0U _58 Vehicle Interior _049337 THEFT DETERRENT / KEYLESS ENTRY _0235822 ENGINE IMMOBILISER SYSTEM U

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  TERMINALS OF ECU  


CHECK TRANSPONDER KEY ECU ASSEMBLY


U153376E02
3.375,0.625 3.698,0.781 0.323,0.156 10 false H32

a.

Disconnect the H32 transponder key ECU assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
H32-1 (+B) - H32-5 (GND) Input G - W-B Battery Always 11 to 14 V +B
H32-2 (IG) - H32-5 (GND) Input GR - W-B Ignition switch signal Ignition switch off Below 1 V IG SW
Ignition switch ON 11 to 14 V
H32-3 (KSW) - H32-5 (GND) Input LG - W-B Unlock warning switch signal No key in ignition key cylinder 10 kΩ or higher Key SW/B2780
Key in ignition key cylinder Below 1 Ω
H32-5 (GND) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
H32-7 (CTY) - Body ground Input Y - Body ground Door courtesy switch (for driver side) signal Driver side door closed 10 kΩ or higher -
Driver side door open Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the H32 transponder key ECU assembly connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
H32-8 (IND) - H32-5 (GND) Output V - W-B Security indicator signal No key in ignition key cylinder, or 20 seconds elapsed after turning ignition switch to ACC or off (immobiliser system set) Pulse generation Immobiliser
Key in ignition key cylinder (immobiliser system unset) Below 1 V
H32-9 (D) - H32-5 (GND) Input/Output B - W-B DLC3 communication Without communication Below 1 V -
During communication Pulse generation
H32-4 (ANT1) - H32-5 (GND) Input/Output L - W-B Transponder key amplifier power source No key in ignition key cylinder 4 to 6 V -
Within 3 seconds of inserting key into ignition key cylinder Pulse generation
(See waveform 1)
H32-15 (ANT2) - H32-5 (GND) Input/Output W - W-B Transponder key amplifier communication signal No key in ignition key cylinder 4 to 6 V -
Within 3 seconds of inserting key into ignition key cylinder Pulse generation
(See waveform 2)
H32-12 (EFII) - H32-5 (GND) Output SB - W-B ECM input signal Ignition switch off 11 to 14 V -
H32-12 (EFII) - H32-5 (GND) Output SB - W-B ECM input signal Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 3)
-
H32-13 (EFIO) - H32-5 (GND) Input Y - W-B ECM output signal Ignition switch off Below 1 V -
Ignition switch ON Pulse generation
(See waveform 4)

If the result is not as specified, the transponder key ECU assembly may be malfunctioning.


e.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B329909E04
5.771,0.833 6.229,1.031 0.458,0.198 10 false GND

Tester Connection H32-4 (ANT1) - H32-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of inserting key into ignition key cylinder


ii.

Waveform 2 (Reference)

B329910E01
5.75,0.854 6.208,1.052 0.458,0.198 10 GND

Tester Connection H32-15 (ANT2) - H32-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of inserting key into ignition key cylinder


iii.

Waveform 3 (Reference)

B325134E02
0.906,1.25 1.365,1.448 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Tester Connection H32-12 (EFII) - H32-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


iv.

Waveform 4 (Reference)

B333259E03
0.854,1.26 1.229,1.438 0.375,0.177 10 false GND 3.313,1.365 3.51,1.542 0.198,0.177 10 false *b 3.125,1.354 3.323,1.531 0.198,0.177 10 false *a

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Tester Connection H32-13 (EFIO) - H32-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Ignition switch ON




CHECK ECM (for 3UR-FE, 3UR-FBE)


U153064E02
5.542,0.292 5.802,0.469 0.26,0.177 10 false A27 2.313,0.292 2.583,0.469 0.271,0.177 10 false D56

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
D56-81 (E1) - Body ground - BR - Body ground Ground Always Below 1 Ω -
D56-43 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
D56-42 (E02) - Body ground - BR - Body ground Ground Always Below 1 Ω -
A27-1 (BATT) - D56-81 (E1) Input L - BR +B power supply Always 11 to 14 V -
A27-2 (+B2) - D56-81 (E1) Input GR - BR +B power supply Ignition switch ON 11 to 14 V -
A27-3 (+B) - D56-81 (E1) Input GR - BR +B power supply Ignition switch ON 11 to 14 V -
A27-29 (IMO) - D56-81 (E1) Input P - BR Transponder key ECU assembly communication input Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 1)
-
A27-40 (IMI) - D56-81 (E1) Output B - BR Transponder key ECU assembly communication output Ignition switch off Below 1 V -
Ignition switch ON Pulse generation
(See waveform 2)
-

a.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B333258E03
0.865,1.25 1.292,1.469 0.427,0.219 10 false GND 2.719,1.333 2.969,1.563 0.25,0.229 10 false *a 2.917,1.333 3.167,1.552 0.25,0.219 10 false *b

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Tester Connection A27-29 (IMO) - D56-81 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259E02
0.848,1.231 1.218,1.405 0.370,0.173 10 GND 3.31,1.366 3.505,1.539 0.195,0.173 10 *b 3.119,1.352 3.314,1.525 0.195,0.173 10 *a

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Tester Connection A27-40 (IMI) - D56-81 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Ignition switch ON