Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM27L0U _58 Vehicle Interior _049339 METER / GAUGE / DISPLAY _0235844 METER / GAUGE SYSTEM D

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  OPERATION CHECK  


INSPECT INDICATOR/WARNING LIGHT


HINT:

In this inspection, an indicator or warning light might come on differently than is specified, under some normal conditions.


a.

Check the following indicators and warning lights.

Warning/Indicator Light Switch Condition Specified Condition
Height control HI indicator light*1 Ignition switch off → ON Comes on for 2 seconds
Height control N indicator light*1 Ignition switch off → ON Comes on for 2 seconds
Height control LO indicator light*1 Ignition switch off → ON Comes on for 2 seconds
Height control MAN. indicator light*1 Ignition switch off → ON Comes on for 2 seconds
Brake warning light Ignition switch off → ON Comes on for 3 seconds
ABS warning light Ignition switch off → ON Comes on for 3 seconds
SLIP indicator light Ignition switch off → ON Comes on for 3 seconds
AUTO LSD indicator light Ignition switch off → ON Comes on for 3 seconds
VSC OFF indicator light Ignition switch off → ON Comes on for 3 seconds
TOW HAUL indicator light*2 Ignition switch off → ON Comes on for 3 seconds
EPS warning light Ignition switch off → ON Comes on for 3 seconds
Tire pressure warning light Ignition switch off → ON Comes on for 3 seconds
MAIN REQD indicator light*3 Ignition switch off → ON Comes on for 3 seconds
SRS warning light Ignition switch off → ON Comes on for 6 seconds
A/T OIL TEMP warning light Ignition switch off → ON Illuminates when ignition switch is turned to ON.
Turns off when engine is started.
CHARGE warning light Ignition switch off → ON Illuminates when ignition switch is turned to ON.
Turns off when engine is started.
MIL Ignition switch off → ON Illuminates when ignition switch is turned to ON.
Turns off when engine is started.

*1: w/ Air Suspension

*2: w/ Towing Package

*3: for U.S.A. without Multi-information Display




INSPECT SPEEDOMETER


a.

Connect the Techstream to the DLC3 connector.


b.

Turn the ignition switch ON.


c.

Turn the Techstream ON.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

According to the display on Techstream, read the Data List.

Reference:
for mph
Techstream Display Speedometer Display
20 mph 19 to 22 mph
40 mph 39 to 42.5 mph
60 mph 59.5 to 63.5 mph
80 mph 79.5 to 84 mph
100 mph 100 to 105 mph

for km/h
Techstream Display Speedometer Display
Data in ( ) is for reference
20 km/h (17.5 to 21.5 km/h)
40 km/h 38 to 42 km/h
60 km/h 58 to 63 km/h
80 km/h 78 to 84 km/h
100 km/h 98.5 to 104.5 km/h
120 km/h 119 to 125 km/h
140 km/h 139 to 146 km/h
160 km/h 159 to 167 km/h
180 km/h 179 to 188 km/h


NOTICE:

Do not use worn, underinflated or overinflated tires, as the speedometer reading will be inaccurate.



f.

Check the deflection width of the speedometer indicator.

Reference:

0.5 km/h (0.3 mph)




INSPECT TACHOMETER


a.

Connect a tune-up tachometer, and start the engine.


b.

Compare the test results with the tachometer indicator.

DC 13.5 V, at 25°C (77°F):
Standard indication (rpm) Acceptable range
Data in ( ) is for reference
700 630 to 770
1000 (900 to 1100)
2000 (1850 to 2150)
3000 2800 to 3200
4000 (3800 to 4200)
5000 4800 to 5200
6000 (5750 to 6250)


If the result is not as specified, the speedometer may have a malfunction.



INSPECT METER/GAUGE


a.

Connect the Techstream to the DLC3.


b.

Perform Active Test (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

OK:

All meter/gauge needle indicators are normal.




INSPECT WARNING/INDICATOR LIGHT


a.

Connect the Techstream to the DLC3.


b.

Perform Active Test (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

OK:

Each warning/indicator light turns ON and OFF using tester.




INSPECT MULTI-INFORMATION DISPLAY (w/ Multi-information Display)


a.

Connect the Techstream to the DLC3.


b.

Perform Active Test (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

HINT:

If this Active Test is being performed and the ignition switch is turned off and then ON, the A/T and ODO/TRIP display background may turn white. If this occurs, end this Active Test and turn the ignition switch off.


OK:

All dots in the multi-information display turn ON and OFF using Techstream.