Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27L0U _58 Vehicle Interior _049341 SUPPLEMENTAL RESTRAINT SYSTEMS _0235848 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  Diagnosis Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

DTCs are displayed by blinking of the SRS warning light.

HINT:
·

When each warning light stays blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in each ECU is suspected.

·

A DTC output mode signal is transmitted through CAN communication system to each ECU including the center airbag sensor. Thus when all systems do not enter DTC output mode, there may be an ECM malfunction.



WIRING DIAGRAM

C162321E03
1.316,1.416 1.578,1.582 0.262,0.165 10 TC 1.64,1.302 1.826,1.459 0.185,0.157 10 16 3.608,1.318 3.793,1.474 0.185,0.157 10 4 2.539,1.318 2.724,1.474 0.185,0.157 10 13 1.037,1.958 1.333,2.118 0.296,0.159 10 A27 1.026,2.105 1.396,2.276 0.370,0.171 10 ECM 0.876,4.363 1.549,4.522 0.673,0.159 10 CAN Line 2.961,1.958 3.288,2.126 0.327,0.168 10 H19 2.961,2.105 3.382,2.276 0.422,0.171 10 DLC3 2.833,1.439 3.095,1.604 0.262,0.165 10 TC 3.282,1.439 3.544,1.604 0.262,0.165 10 CG 5.465,3.668 5.773,3.839 0.308,0.171 10 H56 5.465,3.835 6.823,4.006 1.358,0.171 10 Center Airbag Sensor 1.316,3.057 1.578,3.222 0.262,0.165 10 TC 1.64,2.929 1.738,3.086 0.098,0.157 10 3 0.532,3.657 0.820,3.802 0.288,0.145 10 H40 0.532,3.818 2.275,3.967 1.743,0.149 10 Tire Pressure Warning ECU

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication system DTC is output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

2.CHECK HARNESS AND CONNECTOR (DLC3 - ECM)

B

2.CHECK HARNESS AND CONNECTOR (DLC3 - ECM)
a.

Turn the ignition switch off.

C353062E02
0.5,1.5 0.896,1.771 0.396,0.271 3.667,1.469 4.063,1.74 0.396,0.271 1.917,1.552 2.229,1.177 true 2.156,2.292 2.052,1.875 true 6.104,0.792 5.958,1.479 true 0.469,0.219 3.375,0.417 2.906,0.198 10 false Front view of DLC3: 4.219,0.208 6.49,0.594 2.271,0.385 10 false Front view of wire harness connector: (ECM) 0.604,1.552 1.063,1.75 0.458,0.198 10 false H19 3.75,1.51 4.208,1.708 0.458,0.198 10 false A27 6.146,0.625 6.458,0.823 0.313,0.198 10 false TC 2.083,2.323 2.396,2.521 0.313,0.198 10 false TC 2.271,1.073 2.583,1.271 0.313,0.198 10 false CG


b.

Disconnect the A27 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H19-13 (TC) - A27-16 (TC) Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)
a.
U154207E01
0.056,0.045 1.330,0.221 1.274,0.177 10 Front view of DLC3: 0.156,1.185 0.486,1.340 0.330,0.156 10 H19 1.832,1.806 2.162,1.962 0.330,0.156 10 CG 1.606,1.033 1.965,1.761 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H19-4 (CG) - Body ground Always Below 1 Ω




OK

4.CHECK HARNESS AND CONNECTOR (TC OF ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (TC OF ECM - BODY GROUND)
a.
U153542E01
0.075,0.225 2.439,0.576 2.364,0.350 10 Front view of wire harness connector: (to ECM) 0.319,1.544 0.598,1.713 0.278,0.169 10 A27 2.647,1.183 2.922,1.359 0.275,0.176 10 TC 2.356,2.144 2.609,1.313 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A27-16 (TC) - Body ground Always 1 MΩ or higher


Result
Result Proceed to
OK (for 3UR-FE) A
OK (for 3UR-FBE) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR OR EACH ECU