Home › Vehicle Interior › SEAT › REAR NO. 1 SEAT ASSEMBLY
RM27L0U _58 Vehicle Interior _049342 SEAT _0235863 REAR NO. 1 SEAT ASSEMBLY A

SEAT  REAR NO. 1 SEAT ASSEMBLY  DISASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below are for the RH side.



PROCEDURE

Hide 72572B 1.REMOVE RECLINING ADJUSTER KNOB CAP RH

a.
B191081E03
2.479,1.24 2.094,1.375 true 2.51,1.167 2.677,1.323 0.167,0.156 10 true *1

Using a screwdriver, detach the 3 claws and remove the reclining adjuster knob cap.

Text in Illustration
*1 Protective Tape

HINT:

Tape the screwdriver tip before use.



Hide 72735 2.REMOVE REAR SEAT RECLINING RELEASE LEVER

a.
B191083

Remove the 3 screws and rear seat reclining release lever.


Hide 71692H 3.REMOVE REAR SEAT CUSHION HINGE COVER NO. 3

B191084

a.

Remove the screw.


b.

Detach the 2 claws and remove the rear seat cushion hinge cover.


Hide 71691H 4.REMOVE REAR SEAT CUSHION HINGE COVER NO. 2

B191085

a.

Remove the screw.


b.

Detach the 2 claws and remove the rear seat cushion hinge cover.


Hide 73380A 5.REMOVE REAR SEAT INNER BELT ASSEMBLY

Hide 6.REMOVE REAR NO. 1 SEAT CUSHION ASSEMBLY RH

a.
B191090

Disconnect the connector and detach the 3 clamps.

HINT:

If the vehicle is equipped with the seat heater system, disconnect the connector and detach the clamps.



b.
B191088

Cut the cable tie.


c.

Disconnect the cable from the seat cushion spring.


d.
B191089

Cut the cable tie to remove the cable from the seat cushion spring.


e.

Detach the cable clamp and remove the cable from the seat cushion spring.


f.
B232098

Detach the 2 clamps to remove the cable from the seat cushion spring.


g.
B191091

Remove the 2 bolts.


h.

Using a T45 "TORX" socket, remove the 2 "TORX" bolts and 2 bushes. Then remove the rear No. 1 seat cushion assembly.


Hide 71650B 7.REMOVE REAR SEAT CUSHION SPRING ASSEMBLY RH (w/ Seat Heater System)

a.
B200241

Remove the 9 hog rings.


b.
B200247

Detach the hooks and remove the rear seat cushion spring assembly.


Hide 71650B 8.REMOVE REAR SEAT CUSHION SPRING ASSEMBLY RH (w/o Seat Heater System)

a.
B200241

Remove the 9 hog rings.


b.
B191092

Detach the hooks and remove the rear seat cushion spring assembly.


Hide 71075S 9.REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER

a.
B191094

Remove the 8 hog rings and separate type rear seat cushion cover.


Hide 87510P 10.REMOVE SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)

Hide 72995B 11.REMOVE NO. 1 SEAT CUSHION COVER RH

a.
B191122

Detach the cable clamp and disconnect the cable from the No. 1 seat cushion cover.


b.

Remove the 2 screws.


c.

Detach the claw and remove the No. 1 seat cushion cover.


Hide 87501A 12.REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY RH (w/ Seat Heater System)

a.
B200248

Cut the cable tie.


b.

Detach the 5 harness clamps and remove the seat heater control sub-assembly.


c.

Disconnect the seat heater connector.


Hide 71940A 13.REMOVE REAR SEAT HEADREST ASSEMBLY

Hide 72615C 14.REMOVE REAR SEATBACK LOCK STRIKER COVER

a.
B191098E02
0.827,1.375 1.007,1.524 0.180,0.149 10 *1 1.011,1.452 2.006,1.494 false

Using a screwdriver, detach the claw and guide and remove the rear seatback lock striker cover.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*1 Protective Tape


Hide 72057 15.REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH

a.
B191100

Remove the 2 screws.


b.

Disconnect the cable and remove the rear seat lock control lever sub-assembly.


Hide 72848A 16.REMOVE REAR NO. 1 SEAT ARMREST CAP (w/ Armrest)

a.
B195221

Detach the 3 claws and remove the rear No. 1 seat armrest cap.


Hide 72810A 17.REMOVE SEAT ARMREST ASSEMBLY RH (w/ Armrest)

a.
B195222

Remove the bolt and seat armrest assembly.


Hide 71701B 18.REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY RH

a.
B191101

Detach the 7 clips and remove the rear seatback board sub-assembly.


Hide 71691E 19.REMOVE REAR SEAT CUSHION HINGE COVER NO. 1

a.
B191095

Remove the screw.


b.

Detach the 4 claws and clip and remove the rear seat cushion hinge cover.


Hide 71629A 20.REMOVE REAR SEAT CUSHION HINGE COVER RH

a.
B191096

Remove the 2 screws.


b.

Detach the 3 claws and remove the rear seat cushion hinge cover.


Hide 72927 21.REMOVE REAR SEAT CUSHION UNDER COVER RH

a.
B191097

Remove the 3 screws and rear seat cushion under cover.


Hide 71931A 22.REMOVE REAR SEAT HEADREST SUPPORT

a.
B191133

Detach the 4 claws and remove the 2 rear seat headrest supports.


Hide 79013 23.REMOVE NO. 1 SEATBACK COVER SUB-ASSEMBLY RH

a.
B200243

Remove the 2 hog rings.


b.

Remove the hooks and No. 1 seatback cover sub-assembly.


Hide 24.REMOVE SEATBACK COVER WITH PAD

a.
B191102

Remove the 2 hog rings.


b.
B191104

Detach the hooks and remove the seatback cover with pad.


Hide 71077S 25.REMOVE SEPARATE TYPE REAR SEATBACK COVER

a.
B191106

Remove the 8 hog rings and separate type rear seatback cover from the seatback pad.


Hide 87510R 26.REMOVE SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)

Hide 71834A 27.REMOVE REAR SEAT RECLINING COVER NO. 1 LH

a.
B191110

Remove the screw.


b.

Detach the guide and remove the rear seat reclining cover.


Hide 71878A 28.REMOVE REAR SEAT RECLINING COVER INNER RH

a.
B191118

Pull the cable through the rear seatback frame sub-assembly.


b.
B191112

Remove the screw.


c.

Detach the 3 claws and remove the rear seat reclining cover.


Hide 71017 29.REMOVE REAR SEATBACK FRAME SUB-ASSEMBLY RH

a.
B191113

Disconnect the 2 clamps.


b.

Rotate the cable ends and remove the cables.


c.
B191115

Cut the cable tie.


d.

Disconnect the 2 cables from the rear seatback frame sub-assembly.

HINT:

When removing the upper cable, operate the release pedal at the back of the seat to make it easier to disconnect the cable. However, be careful because the seatback will fall forward.



e.
B191117

Using a T45 "TORX" socket, remove the 5 "TORX" bolts and rear seatback frame sub-assembly.


Hide 71385B 30.REMOVE REAR SEAT CUSHION HOLDER BRACKET RH

a.
B200245

Remove the bolt and rear seat cushion holder bracket.


Hide 72067 31.REMOVE REAR BACK LOCK CONTROL LEVER SUB-ASSEMBLY RH

a.
B200246

Remove the E-ring and washer.


b.
B191119

Using a T40 "TORX" socket, remove the "TORX" bolt.


c.

Remove the 3 nuts to remove the rear back lock control lever sub-assembly and rear seat cushion lock striker sub-assembly.


Hide 71879A 32.REMOVE REAR SEAT RECLINING COVER INNER LH

a.
B191111

Remove the screw.


b.

Detach the guide and remove the rear seat reclining cover.


Hide 71879B 33.REMOVE REAR SEAT RECLINING COVER INNER

a.
B191121

Remove the 2 screws and rear seat reclining cover.


Hide 72997 34.REMOVE REAR SEATBACK COVER LH

a.
B195212

Remove the screw and rear seatback cover.


b.

Detach the cable clamp and disconnect the rear seatback lock control No. 2 cable sub-assembly.


Hide 72996 35.REMOVE REAR SEATBACK COVER RH

a.
B195213

Remove the screw and rear seatback cover.


Hide 72069 36.REMOVE REAR SEATBACK LOCK CONTROL NO. 2 CABLE SUB-ASSEMBLY

a.
B195214

Disconnect the rear seatback lock control No. 2 cable sub-assembly.

HINT:
·

The front nut is locked with adhesive. Loosen the rear nut to remove the cable.

·

If the front nut becomes loose, adjust the length when installing the cable.




b.

Rotate the cable end to remove it.


Hide 72704B 37.REMOVE REAR SEAT RECLINING CONTROL NO. 2 CABLE

a.
B222186

Cut the 3 cable ties and remove the rear seat reclining control No. 2 cable and rear seatback lock control No. 1 cable sub-assembly


Hide 71461A 38.REMOVE REAR SEAT CUSHION SPRING NO. 1

a.
B191129

Remove the rear seat cushion spring.


Hide 72630B 39.REMOVE REAR NO. 1 SEAT ADJUSTER ASSEMBLY INNER RH

a.
B191126

Disconnect the rear No. 1 seat lock cable assembly LH.

HINT:
·

The front nut is locked with adhesive. Loosen the rear nut to remove the cable.

·

If the front nut becomes loose, adjust the length when installing the cable.




b.

Rotate the cable end to remove it.


c.
B191130

Remove the 2 nuts and rear seat cushion support bracket.


d.

Remove the nut and rear No. 1 seat adjuster assembly.


e.
B222193

Remove the washer.


Hide 72730E 40.REMOVE REAR SEATBACK ADJUSTER ASSEMBLY OUTER RH

a.
B191124

Disconnect the rear No. 1 seat lock cable assembly RH.

HINT:
·

The front nut is locked with adhesive. Loosen the rear nut to remove the cable.

·

If the front nut becomes loose, adjust the length when installing the cable.




b.

Rotate the cable end to remove it.


c.
B191131

Remove the 3 nuts and rear No. 1 seat adjuster assembly.


d.
B222191

Remove the washer.


Hide 72173A 41.REMOVE REAR SEAT TRACK ADJUSTING HANDLE RH

a.

Slide the slide rail to the rearmost position.

B443318E01
5.021,2 5.385,1.542 false 5.427,2.177 5.646,1.906 false 4.875,2.896 5.094,2.552 true 6.083,2.885 6.083,2.51 true 5.427,1.427 5.74,1.625 0.313,0.198 10 false *1 5.688,1.802 6,2 0.313,0.198 10 false *2 4.708,2.906 4.896,3.083 0.188,0.177 10 false *3 6.021,2.969 6.208,3.146 0.188,0.177 10 false *4

Text in Illustration
*1 Screwdriver
*2 Seat Track
*3 Handle Stopper
*4 Track Adjusting Handle


b.

Using a small screwdriver, push down the handle stopper to disengage the claw and remove the adjusting handle.

HINT:

Insert the screwdriver in the hole shown in the illustration, while looking into the hole.