Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM27L0U _58 Vehicle Interior _049344 HEATING / AIR CONDITIONING _0235901 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1412/12  Ambient Temperature Sensor Circuit  


DESCRIPTION

The thermistor assembly (ambient temperature sensor) is installed in front of the condenser to detect the ambient temperature which is used to control the air conditioner "AUTO" mode. This sensor is connected to the air conditioning amplifier and detects fluctuations in the ambient temperature. This data is used for controlling the cabin temperature. The sensor sends a signal to the air conditioning amplifier. The resistance of the thermistor assembly (ambient temperature sensor) changes in accordance with the ambient temperature. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier applies voltage (5 V) to the thermistor assembly (ambient temperature sensor) and reads voltage changes as the resistance of the thermistor assembly (ambient temperature sensor) changes.

DTC Code DTC Detection Condition Trouble Area
B1412/12 Open or short in ambient temperature sensor circuit
·

Thermistor assembly (ambient temperature sensor)

·

Harness or connector between thermistor assembly (ambient temperature sensor) and air conditioning amplifier

·

Air conditioning amplifier



WIRING DIAGRAM

E344814E05
4.542,1.094 4.688,1.302 0.146,0.208 10 false 5 2.396,1.104 2.552,1.302 0.156,0.198 10 false 1 2.385,1.969 2.542,2.167 0.156,0.198 10 false 2 4.49,1.969 4.698,2.167 0.208,0.198 10 false 13 4.896,1.208 5.25,1.406 0.354,0.198 10 false TAM 4.896,2.094 5.271,2.292 0.375,0.198 10 false SG-2 0.5,2.656 0.781,2.854 0.281,0.198 10 false A18 0.49,2.844 2.229,3.073 1.74,0.229 10 false Thermistor Assembly 5.01,2.656 5.292,2.854 0.281,0.198 10 false H24 5.01,2.833 6.594,3.063 1.583,0.229 10 false Air Conditioning Amplifier 0.469,3.021 5.208,3.219 4.74,0.198 10 false (Ambient Temperature Sensor)

PROCEDURE

1.READ VALUE USING TECHSTREAM (AMBIENT TEMPERATURE SENSOR)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List / Ambient Temp Sensor.


e.

According to the display on the Techstream, read the Data List.

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Ambient Temp Sensor Ambient temperature sensor /
Min.: -23.3°C (-9.94°F)
Max.: 65.95°C (150.71°F)
Actual ambient temperature is displayed Open circuit: -23.3°C (-9.94°F)
Short circuit: 65.95°C (150.71°F)

OK:

The display is as specified in the normal condition.


Result
Result Proceed to
NG A
OK (When troubleshooting according to Problem Symptoms Table) B
OK (When troubleshooting according to the DTC output) C



A

2.INSPECT THERMISTOR ASSEMBLY (AMBIENT TEMPERATURE SENSOR)

B

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C

2.INSPECT THERMISTOR ASSEMBLY (AMBIENT TEMPERATURE SENSOR)
a.

Remove the thermistor assembly (ambient temperature sensor) (See page Vehicle Interior>HEATING / AIR CONDITIONING>AMBIENT TEMPERATURE SENSOR>REMOVAL).

E344817E02
2.719,1.708 2.25,0.969 false 0.406,0.135 2.958,0.813 2.552,0.677 10 false Component without harness connected: (Thermistor Assembly (Ambient Temperature Sensor)) 1.448,0.844 2.396,1.073 0.948,0.229 10 false Sensor Area 4.167,0.021 5.25,0.25 1.083,0.229 10 false Resistance (kΩ) 4.313,0.302 4.583,0.49 0.271,0.188 10 false 4.0 4.313,0.521 4.583,0.708 0.271,0.188 10 false 3.5 4.302,0.74 4.573,0.927 0.271,0.188 10 false 3.0 4.292,0.969 4.563,1.156 0.271,0.188 10 false 2.5 4.292,1.208 4.563,1.396 0.271,0.188 10 false 2.0 4.292,1.448 4.563,1.635 0.271,0.188 10 false 1.5 4.292,1.688 4.563,1.875 0.271,0.188 10 false 1.0 4.292,1.917 4.563,2.104 0.271,0.188 10 false 0.5 4.292,2.135 4.563,2.323 0.271,0.188 10 false 0.0 4.531,2.198 4.75,2.385 0.219,0.188 10 false 10 4.49,2.333 4.74,2.531 0.25,0.198 10 false (50) 4.969,2.198 5.188,2.385 0.219,0.188 10 false 20 5.427,2.198 5.646,2.385 0.219,0.188 10 false 30 5.906,2.198 6.125,2.385 0.219,0.188 10 false 40 6.375,2.198 6.594,2.385 0.219,0.188 10 false 50 6.844,2.198 7.063,2.385 0.219,0.188 10 false 60 4.927,2.333 5.177,2.531 0.25,0.198 10 false (68) 5.385,2.323 5.635,2.521 0.25,0.198 10 false (86) 5.854,2.333 6.167,2.531 0.313,0.198 10 false (104) 6.281,2.323 6.594,2.521 0.313,0.198 10 false (122) 6.75,2.323 7.063,2.521 0.313,0.198 10 false (140) 5.042,2.573 6.323,2.75 1.281,0.177 10 false Temperature °C (°F)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 10°C (50°F) 3.00 to 3.73 kΩ
15°C (59°F) 2.45 to 2.88 kΩ
20°C (68°F) 1.95 to 2.30 kΩ
25°C (77°F) 1.60 to 1.80 kΩ
30°C (86°F) 1.28 to 1.47 kΩ
35°C (95°F) 1.00 to 1.22 kΩ
40°C (104°F) 0.80 to 1.00 kΩ
45°C (113°F) 0.65 to 0.85 kΩ
50°C (122°F) 0.50 to 0.70 kΩ
55°C (131°F) 0.44 to 0.60 kΩ
60°C (140°F) 0.36 to 0.50 kΩ


HINT:
·

Even slightly touching the sensor may change the resistance value. Be sure to hold the connector of the sensor.

·

When measuring, the sensor temperature must be the same as the ambient temperature.

·

As the temperature increases, the resistance decreases (see the graph).




c.

Reinstall the thermistor assembly (ambient temperature sensor).



OK

3.CHECK HARNESS AND CONNECTOR (AMBIENT TEMPERATURE SENSOR - AIR CONDITIONING AMPLIFIER)

NG

REPLACE THERMISTOR ASSEMBLY (AMBIENT TEMPERATURE SENSOR)

3.CHECK HARNESS AND CONNECTOR (AMBIENT TEMPERATURE SENSOR - AIR CONDITIONING AMPLIFIER)
a.
E345191E01
0.667,1.115 1.073,1.344 0.406,0.229 0.573,3.854 0.979,4.083 0.406,0.229 1.302,4.208 1.719,3.792 true 2.635,4.208 2.281,3.781 true 0.729,0.188 3.021,0.927 2.292,0.74 10 false Front view of wire harness connector: (to Thermistor Assembly (Ambient Temperature Sensor)) 0.76,1.146 1.219,1.344 0.458,0.198 10 false A18 0.635,1.844 2.906,2.5 2.271,0.656 10 false Rear view of wire harness connector: (Air Conditioning Amplifier) 0.677,3.885 1.135,4.083 0.458,0.198 10 false H24 1.042,4.229 1.656,4.427 0.615,0.198 10 false SG-2 2.594,4.229 3.208,4.427 0.615,0.198 10 false TAM

Disconnect the A18 thermistor assembly (ambient temperature sensor) connector.


b.

Disconnect the H24 air conditioning amplifier connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A18-1 - H24-5 (TAM) Always Below 1 Ω
A18-2 - H24-13 (SG-2) Always Below 1 Ω
A18-1 or H24-5 (TAM) - Body ground Always 10 kΩ or higher
A18-2 or H24-13 (SG-2) - Body ground Always 10 kΩ or higher



d.

Reconnect the air conditioning amplifier connector.


e.

Reconnect the thermistor assembly (ambient temperature sensor) connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR