Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM27L0U _58 Vehicle Interior _049344 HEATING / AIR CONDITIONING _0235901 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1413/13  Evaporator Temperature Sensor Circuit  


DESCRIPTION

The No. 1 cooler thermistor (evaporator temperature sensor) is installed on the evaporator in the air conditioner unit to detect the cooled air temperature that has passed through the evaporator and control the air conditioning. It sends appropriate signals to the air conditioning amplifier. The resistance of the No. 1 cooler thermistor (evaporator temperature sensor) changes in accordance with the cooled air temperature that has passed through the evaporator. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier applies voltage (5 V) to the No. 1 cooler thermistor (evaporator temperature sensor) and reads voltage changes as the resistance of the No. 1 cooler thermistor (evaporator temperature sensor) changes. This sensor is used for frost prevention.

DTC Code DTC Detection Condition Trouble Area
B1413/13 Open or short in evaporator temperature sensor circuit
·

No. 1 cooler thermistor (evaporator temperature sensor)

·

Air conditioning harness

·

Air conditioning amplifier



WIRING DIAGRAM

E147578E07
1.079,2.461 3.461,2.790 2.383,0.330 10 No. 1 Cooler Thermistor (Evaporator Temperature Sensor) 5.385,2.377 5.743,2.536 0.358,0.160 10 z13 5.385,2.546 7.020,2.715 1.635,0.170 10 Air Conditioning Amplifier 3.676,2.546 5.283,2.715 1.607,0.170 10 Air Conditioning Harness 5.487,0.951 5.830,1.155 0.343,0.205 10 TEA 5.487,1.779 5.830,1.983 0.343,0.205 10 SGA 5.288,0.852 5.441,1.005 0.152,0.152 10 6 5.288,1.681 5.441,1.833 0.152,0.152 10 5 3.79,1.624 3.885,1.810 0.096,0.186 10 1 3.797,0.826 3.897,0.991 0.100,0.165 10 2

PROCEDURE

1.READ VALUE USING TECHSTREAM (EVAPORATOR FIN THERMISTOR)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List / Evaporator Fin Thermistor.


e.

According to the display on the Techstream, read the Data List.

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Evaporator Fin Thermistor Evaporator fin thermistor /
Min.: -29.7°C (-21.46°F)
Max.: 59.55°C (139.19°F)
Actual evaporator temperature is displayed Open circuit: -29.7°C (-21.46°F)
Short circuit: 59.55°C (139.19°F)

OK:

The display is as specified in the normal condition.


Result
Result Proceed to
NG A
OK (When troubleshooting according to Problem Symptoms Table) B
OK (When troubleshooting according to the DTC output) C



A

2.INSPECT NO. 1 COOLER THERMISTOR (EVAPORATOR TEMPERATURE SENSOR)

B

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C

2.INSPECT NO. 1 COOLER THERMISTOR (EVAPORATOR TEMPERATURE SENSOR)
E345192E01
1.771,0.469 1.417,0.188 false 0.875,1.885 1.042,1.51 false 0.76,3.052 1.115,2.969 true 0.729,0.083 2.26,0.281 1.531,0.198 10 false Evaporator 0.469,1.906 3.99,2.104 3.521,0.198 10 false No. 1 Cooler Thermistor 1.167,2.875 2.854,3.073 1.688,0.198 10 false Sensor Area 0.458,3.531 3.979,3.729 3.521,0.198 10 false No. 1 Cooler Thermistor 4.042,0.167 6.333,0.365 2.292,0.198 10 false Resistance (kΩ) 3.958,0.781 4.573,0.979 0.615,0.198 10 false 10.0 4.031,0.948 4.573,1.156 0.542,0.208 10 false 9.0 4.031,1.135 4.573,1.344 0.542,0.208 10 false 8.0 4.031,1.323 4.573,1.531 0.542,0.208 10 false 7.0 4.031,1.51 4.573,1.719 0.542,0.208 10 false 6.0 4.031,1.698 4.573,1.906 0.542,0.208 10 false 5.0 4.031,1.865 4.573,2.073 0.542,0.208 10 false 4.0 4.031,2.031 4.573,2.24 0.542,0.208 10 false 3.0 4.031,2.208 4.573,2.417 0.542,0.208 10 false 2.0 4.031,2.375 4.573,2.583 0.542,0.208 10 false 1.0 4.031,2.563 4.573,2.771 0.542,0.208 10 false 0.0 4.146,2.729 4.604,2.927 0.458,0.198 10 false -10 4.823,2.729 5.198,2.927 0.375,0.198 10 false 0 5.365,2.729 5.74,2.927 0.375,0.198 10 false 10 5.948,2.729 6.323,2.927 0.375,0.198 10 false 20 6.51,2.719 6.885,2.917 0.375,0.198 10 false 30 4.125,2.896 4.74,3.094 0.615,0.198 10 false (14) 4.74,2.896 5.354,3.094 0.615,0.198 10 false (32) 5.333,2.906 5.948,3.104 0.615,0.198 10 false (50) 5.927,2.906 6.542,3.104 0.615,0.198 10 false (68) 6.49,2.885 7.104,3.083 0.615,0.198 10 false (86) 4.906,3.198 6.167,3.417 1.26,0.219 10 false Temperature °C (°F)

a.

Remove the No. 1 cooler thermistor (evaporator temperature sensor) connector (See page Vehicle Interior>HEATING / AIR CONDITIONING>AMBIENT TEMPERATURE SENSOR>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 -10°C (14°F) 7.30 to 9.10 kΩ
-5°C (23°F) 5.65 to 6.95 kΩ
0°C (32°F) 4.40 to 5.35 kΩ
5°C (41°F) 3.40 to 4.15 kΩ
10°C (50°F) 2.70 to 3.25 kΩ
15°C (59°F) 2.14 to 2.58 kΩ
20°C (68°F) 1.71 to 2.05 kΩ
25°C (77°F) 1.38 to 1.64 kΩ
30°C (86°F) 1.11 to 1.32 kΩ


HINT:
·

Even slightly touching the sensor may change the resistance value. Be sure to hold the connector of the sensor.

·

When measuring, the sensor temperature must be the same as the ambient temperature.

·

As the temperature increases, the resistance decreases (See the graph).




c.

Reinstall the No. 1 cooler thermistor (evaporator temperature sensor) connector.



OK

3.INSPECT AIR CONDITIONING HARNESS

NG

REPLACE NO. 1 COOLER THERMISTOR (EVAPORATOR TEMPERATURE SENSOR)

3.INSPECT AIR CONDITIONING HARNESS
E345193E01
1,4.375 1.781,3.99 true 2.469,4.375 1.969,3.99 true 0.333,0.135 2.76,0.76 2.427,0.625 10 false Component without harness connected: (Air Conditioning Harness) 0.354,0.75 2.406,1.427 2.052,0.677 10 false No. 1 Cooler Thermistor (Evaporator Temperature Sensor) Side: 0.323,2.896 3.385,3.146 3.063,0.25 10 false Air Conditioning Amplifier Side: 0.677,4.302 1.135,4.5 0.458,0.198 10 false TEA 2.531,4.302 2.99,4.5 0.458,0.198 10 false SGA

a.

Remove the air conditioning harness.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 5 (SGA) Always Below 1 Ω
2 - 6 (TEA) Always Below 1 Ω
1 - 6 (TEA) Always 10 kΩ or higher
2 - 5 (SGA) Always 10 kΩ or higher



c.

Reinstall the air conditioning harness.



OK

NG