Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM27L0U _58 Vehicle Interior _049344 HEATING / AIR CONDITIONING _0235901 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1424/24  Solar Sensor Circuit (Driver Side)  


DESCRIPTION

The automatic light control sensor (solar sensor), which is installed on the upper side of the instrument panel, detects sunlight and controls the air conditioning in AUTO mode. The output current from the automatic light control sensor (solar sensor) varies according to the amount of sunlight. When the sunlight increases, the output current increases. As the sunlight decreases, the output current decreases. The air conditioning amplifier detects output current from the automatic light control sensor (solar sensor).

E132508E25
0.448,0.177 2.438,0.427 1.99,0.25 10 false Output Current of Photodiode 0.354,0.781 0.813,1.031 0.458,0.25 10 false High 0.365,2.365 0.823,2.635 0.458,0.271 10 false Low 0.813,2.698 1.333,2.948 0.521,0.25 10 false Weak 2.156,2.677 2.708,2.948 0.552,0.271 10 false Strong 0.802,2.948 2.542,3.188 1.74,0.24 10 false Strength of Solar Radiation

DTC Code DTC Detection Condition Trouble Area
B1424/24 Open or short in driver side solar sensor circuit
·

Automatic light control sensor (solar sensor)

·

Harness or connector between automatic light control sensor (solar sensor) and air conditioning amplifier

·

Harness or connector between automatic light control sensor (solar sensor) and main body ECU

·

Main body ECU

·

Air conditioning amplifier



WIRING DIAGRAM

E147579E04
1.259,0.534 1.664,0.690 0.406,0.156 10 CLTB 1.259,1.052 1.664,1.208 0.406,0.156 10 CLTE 5.202,0.534 5.608,0.690 0.406,0.156 10 CLTB 5.202,1.052 5.608,1.208 0.406,0.156 10 CLTE 1.334,2.436 1.657,2.591 0.323,0.156 10 TSL 5.201,2.436 5.523,2.591 0.323,0.156 10 TSD 4.92,0.424 5.140,0.585 0.220,0.161 10 20 4.92,0.963 5.140,1.124 0.220,0.161 10 18 4.92,2.329 5.140,2.490 0.220,0.161 10 33 1.764,0.433 1.906,0.623 0.142,0.190 10 6 1.764,0.972 1.906,1.163 0.142,0.190 10 3 1.764,2.336 1.906,2.527 0.142,0.190 10 1 0.295,2.96 0.602,3.125 0.307,0.165 10 I21 0.295,3.124 2.347,3.467 2.052,0.343 10 Automatic Light Control Sensor (Solar Sensor) 5.084,2.96 5.391,3.125 0.307,0.165 10 H24 5.084,3.124 6.691,3.339 1.607,0.215 10 Air Conditioning Amplifier 5.343,1.559 5.546,1.724 0.203,0.165 10 H3 5.343,1.723 6.379,1.876 1.036,0.153 10 Main Body ECU

PROCEDURE

1.READ VALUE USING TECHSTREAM (SOLAR SENSOR (D SIDE))
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List / Solar Senor (D Side).


e.

According to the display on the Techstream, read the Data List.

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Solar Sensor (D Side) Driver side solar sensor /
Min.: 0
Max.: 255
Driver side solar sensor voltage increases as brightness increases Open circuit: 0
Short circuit: 255

OK:

The display is as specified in the normal condition.


Result
Result Proceed to
NG A
OK (When troubleshooting according to Problem Symptoms Table) B
OK (When troubleshooting according to the DTC output) C



A

2.CHECK HARNESS AND CONNECTOR (SOLAR SENSOR)

B

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C

2.CHECK HARNESS AND CONNECTOR (SOLAR SENSOR)
a.
U153921E01
1.869,1.754 2.626,1.754 false 1.543,1.577 0.984,1.872 false 0.096,0.032 2.755,0.393 2.659,0.361 10 Front view of wire harness connector: (to Solar Sensor) 0.506,1.866 0.893,2.038 0.387,0.172 10 CLTE 0.652,1.319 0.962,1.493 0.310,0.174 10 I21 2.654,1.643 3.051,1.815 0.397,0.172 10 CLTB

Disconnect the I21 automatic light control sensor (solar sensor) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I21-3 (CLTE) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I21-6 (CLTB) - I21-3 (CLTE) Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



d.

Reconnect the automatic light control sensor (solar sensor) connector.



OK

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - SOLAR SENSOR)

NG

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SOLAR SENSOR, BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - SOLAR SENSOR)
a.

Disconnect the H24 air conditioning amplifier connector.

E345199E02
0.656,1.052 1.052,1.302 0.396,0.25 4.417,1.917 4.813,2.167 0.396,0.25 1.094,2.052 1.719,1.479 true 5.75,2.354 5.417,1.906 true 0.698,0.083 2.969,0.656 2.271,0.573 10 false Rear view of wire harness connector: (to Automatic Light Control Sensor (Solar Sensor)) 0.771,1.094 1.229,1.292 0.458,0.198 10 false I21 0.896,2.073 1.354,2.271 0.458,0.198 10 false TSR 4.198,0.115 6.427,0.667 2.229,0.552 10 false Rear view of wire harness connector: (Air Conditioning Amplifier) 4.5,1.958 4.958,2.156 0.458,0.198 10 false H24 5.781,2.323 6.24,2.521 0.458,0.198 10 false TSD


b.

Disconnect the I21 automatic light control sensor (solar sensor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H24-33 (TSD) - I21-1 (TSL) Always Below 1 Ω
H24-33 (TSD) or I21-1 (TSL) - Body ground Always 10 kΩ or higher



d.

Reconnect the automatic light control sensor (solar sensor) connector.


e.

Reconnect the air conditioning amplifier connector.



OK

4.CHECK AUTOMATIC LIGHT CONTROL SENSOR (SOLAR SENSOR (TSL - CLTE VOLTAGE))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK AUTOMATIC LIGHT CONTROL SENSOR (SOLAR SENSOR (TSL - CLTE VOLTAGE))
a.
E108193E39
1.51,1.594 0.844,1.688 true 1.896,1.417 2.51,1.656 true 1.896,1.198 2.5,0.875 true 0.438,1.615 0.99,1.885 0.552,0.271 10 false CLTB 2.552,0.76 3.052,0.99 0.5,0.229 10 false TSL 2.563,1.594 3.083,1.823 0.521,0.229 10 false CLTE 0.427,0.094 2.698,0.438 2.271,0.344 10 false Component with harness connected: (Automatic Light Control Sensor)

Remove the automatic light control sensor (solar sensor) with its connector still connected (See page Vehicle Interior>HEATING / AIR CONDITIONING>SOLAR SENSOR>REMOVAL).


b.

Apply battery voltage between terminals 6 (CLTB) and 3 (CLTE) of the solar sensor.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (TSL) - 3 (CLTE) Sensor is subjected to electric light 0.8 to 4.3 V
Sensor is covered with a cloth Below 0.8 V


HINT:
·

As the inspection light is moved away from the sensor, the voltage decreases.

·

Use an incandescent light for inspection. Bring it about 30 cm (11.8 in.) from the solar sensor.




d.

Reinstall the automatic light control sensor (solar sensor).



OK

NG

REPLACE AUTOMATIC LIGHT CONTROL SENSOR (SOLAR SENSOR)

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SOLAR SENSOR, BODY GROUND)
U153987E02
2.281,1.563 2.833,1.5 true 2.031,1.573 2.833,1.938 true 1.563,3.885 1.146,4.188 true 1.875,4.083 2.094,4.333 true 0.313,0.208 2.667,0.563 2.354,0.354 10 false Front view of wire harness connector: (to Main Body ECU) 0.313,2.094 2.667,2.604 2.354,0.51 10 false Front view of wire harness connector: (to Automatic Light Control Sensor (Solar Sensor) ) 2.885,1.844 3.26,2.021 0.375,0.177 10 false CLTE 2.875,1.396 3.25,1.573 0.375,0.177 10 false CLTB 0.51,1.458 0.729,1.615 0.219,0.156 10 false H3 0.823,3.74 1.094,3.896 0.271,0.156 10 false I21 1.906,4.344 2.281,4.521 0.375,0.177 10 false CLTB 0.896,4.198 1.271,4.375 0.375,0.177 10 false CLTE

a.

Disconnect the H3 main body ECU connector.


b.

Disconnect the I21 automatic light control sensor (solar sensor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H3-18 (CLTE) - I21-3 (CLTE) Always Below 1 Ω
H3-20 (CLTB) - I21-6 (CLTB) Always Below 1 Ω
H3-18 (CLTE) or I21-3 (CLTE) - Body ground Always 10 kΩ or higher
H3-20 (CLTB) or I21-6 (CLTB) - Body ground Always 10 kΩ or higher



d.

Reconnect the automatic light control sensor (solar sensor) connector.


e.

Reconnect the main body ECU connector.



OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR