Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM27L0U _58 Vehicle Interior _049344 HEATING / AIR CONDITIONING _0235901 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1442/42  Air Inlet Damper Control Servo Motor Circuit  


DESCRIPTION

The recirculation damper servo sends pulse signals to inform the air conditioning amplifier of the damper position. The air conditioning amplifier activates the motor (normal, reverse) based on the signals to move the recirculation damper to any position, which controls the intake air settings (FRESH, FRESH/RECIRCULATION and RECIRCULATION).

HINT:

Confirm that no mechanical problem is present because this diagnostic trouble code can be output when either a damper link or damper is mechanically locked.


DTC Code DTC Detection Condition Trouble Area
B1442/42 Recirculation damper position sensor value does not change even if air conditioning amplifier operated recirculation damper servo motor
·

Recirculation damper servo

·

Air conditioning harness

·

Air conditioning amplifier



WIRING DIAGRAM

E156865E53
1.385,0.458 1.833,0.604 0.448,0.146 10 false SiG. A 1.385,0.76 1.833,0.906 0.448,0.146 10 false SiG. B 1.438,1.115 1.792,1.26 0.354,0.146 10 false GND 2.417,0.323 2.542,0.479 0.125,0.156 10 false 2 2.417,0.646 2.542,0.802 0.125,0.156 10 false 3 2.406,0.958 2.531,1.115 0.125,0.156 10 false 1 2.417,1.271 2.542,1.427 0.125,0.156 10 false 4 2.417,1.573 2.542,1.729 0.125,0.156 10 false 5 2.74,0.302 2.865,0.458 0.125,0.156 10 false 2 2.74,0.646 2.865,0.802 0.125,0.156 10 false 3 2.74,0.938 2.865,1.094 0.125,0.156 10 false 1 2.74,1.26 2.865,1.417 0.125,0.156 10 false 4 2.74,1.573 2.865,1.729 0.125,0.156 10 false 5 5.365,0.74 5.49,0.896 0.125,0.156 10 false 3 5.365,1.365 5.563,1.521 0.198,0.156 10 false 2 5.365,0.042 5.542,0.198 0.177,0.156 10 false 4 3.188,0.948 3.385,1.094 0.198,0.146 10 false IC 0.708,2 2.542,2.156 1.833,0.156 10 false Recirculation Damper Servo 5.521,2.188 6.813,2.635 1.292,0.448 10 false Air Conditioning Amplifier 5.531,1.99 5.802,2.146 0.271,0.156 10 false z13 2.896,2.167 5.375,2.313 2.479,0.146 10 false Air Conditioning Harness Assembly 5.594,0.313 6.125,0.469 0.531,0.156 10 false B BUS 5.594,0.938 5.99,1.094 0.396,0.156 10 false BUS 5.594,1.594 6.073,1.75 0.479,0.156 10 false BUS G

PROCEDURE

1.READ VALUE USING TECHSTREAM (AIR INLET DAMPER TARGET PULSE)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List / Air Inlet Damper Targ Pulse.


e.

According to the display on the Techstream, read the Data List.

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Air Inlet Damper Targ Pulse Air inlet damper target pulse /
Min.: 0
Max.: 255
REC: 7
FRS: 28
-

OK:

The display is as specified in the normal condition.


Result
Result Proceed to
OK (When troubleshooting according to the DTC output) A
OK (When troubleshooting according to Problem Symptoms Table) B
NG C



A

2.REPLACE RECIRCULATION DAMPER SERVO

B

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C

2.REPLACE RECIRCULATION DAMPER SERVO
a.

Temporarily replace the recirculation damper servo with a new one (See page Vehicle Interior>HEATING / AIR CONDITIONING>FRONT AIR CONDITIONING UNIT>DISASSEMBLY).

HINT:

Since the damper servo cannot be inspected while it is removed from the vehicle, replace the damper servo with a new one and check that the condition returns to normal.




NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC

OK

END (RECIRCULATION DAMPER SERVO IS DEFECTIVE)

NG

4.REPAIR OR REPLACE AIR CONDITIONING HARNESS
4.REPAIR OR REPLACE AIR CONDITIONING HARNESS
a.

Repair or replace the air conditioning harness (See page Vehicle Interior>HEATING / AIR CONDITIONING>FRONT AIR CONDITIONING UNIT>DISASSEMBLY ).



NEXT

5.CHECK FOR DTC