Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM27L0U _58 Vehicle Interior _049344 HEATING / AIR CONDITIONING _0235901 AIR CONDITIONING SYSTEM J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  Rear Blower Motor Circuit  


DESCRIPTION

The rear blower motor is operated by signals from the air conditioning amplifier. Rear blower motor speed signals are transmitted in accordance with changes in the duty ratio.

Duty Ratio:

E132503E03
0.139,0.108 1.063,0.281 0.924,0.173 10 Blower Level 0.391,0.53 0.649,0.732 0.258,0.202 10 HI 0.368,1.098 0.640,1.305 0.272,0.207 10 M 0.37,1.671 0.643,1.893 0.273,0.222 10 LO 0.643,2.469 0.799,2.680 0.156,0.211 10 0 1.112,2.461 1.427,2.607 0.315,0.147 10 Low 2.39,2.48 2.767,2.673 0.377,0.193 10 High 1.442,2.75 2.200,2.953 0.758,0.203 10 SI Duty (%) 0.082,3.224 1.130,3.417 1.048,0.193 10 Duty Ratio (%) = 1.601,3.35 2.016,3.515 0.415,0.165 10 A + B 1.75,3.086 1.942,3.279 0.193,0.193 10 B 1.479,3.733 1.672,3.926 0.193,0.193 10 A 1.823,4.129 2.016,4.322 0.193,0.193 10 B 2.516,3.21 2.822,3.378 0.306,0.169 10 100 0.803,3.871 1.088,4.061 0.286,0.191 10 ON 0.768,4.26 1.146,4.444 0.378,0.184 10 OFF 1.611,4.392 2.128,4.533 0.517,0.141 10 1 cycle

The duty ratio is the ratio of the blower motor OFF time (B) to the total of the blower motor ON and OFF time (A + B).

The blower motor controller controls the blower motor speed.

WIRING DIAGRAM

E265175E01
1.65,0.556 1.851,0.711 0.201,0.155 10 +B 2.253,0.695 2.839,0.855 0.587,0.159 10 RR HTR 3.245,0.556 4.048,0.720 0.803,0.164 10 from Battery 1.696,1.198 1.860,1.367 0.164,0.169 10 SI 1.617,2.202 1.860,2.362 0.242,0.159 10 VM 1.534,2.619 1.891,2.779 0.357,0.159 10 GND 1.984,0.449 2.097,0.618 0.114,0.169 10 1 1.984,1.066 2.106,1.221 0.123,0.155 10 3 1.984,2.091 2.111,2.246 0.127,0.155 10 2 1.984,2.476 2.110,2.632 0.126,0.156 10 6 0.639,3.153 0.973,3.335 0.334,0.182 10 P11 0.634,3.315 2.587,3.484 1.952,0.169 10 Rear Blower Motor Control 3.11,2.484 3.224,2.652 0.114,0.169 10 1 3.11,2.086 3.215,2.250 0.104,0.164 10 2 3.281,3.078 3.750,3.236 0.470,0.157 10 P10 3.281,3.234 4.503,3.400 1.223,0.166 10 Rear Blower Motor 5.531,1.066 5.722,1.230 0.192,0.164 10 22 5.814,1.187 6.267,1.337 0.454,0.150 10 BLWH 5.527,2.433 5.725,2.582 0.197,0.149 10 20 5.832,2.545 6.347,2.723 0.515,0.177 10 RGND 5.596,2.986 5.891,3.138 0.295,0.153 10 H67 5.586,3.143 6.638,3.473 1.051,0.330 10 Air Conditioning Amplifier

PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (REAR BLOWER MOTOR)
a.

Connect the Techstream to DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active Test / Rear Blower Motor


e.

According to the display on the Techstream, check rear blower motor operation while performing the Active Test.

Air Conditioner
Tester Display Test Part Control Range Diagnostic Note
Rear Blower Motor Rear blower motor Min.: 0, Max.: 31 -

Result
Result Proceed to
Rear blower motor operates normally A
Rear blower motor does not operate B
Rear blower motor operates but does not change speed C



A

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT FUSE (RR HTR)

C

7.CHECK HARNESS AND CONNECTOR (REAR BLOWER MOTOR CONTROL - AIR CONDITIONING AMPLIFIER)
2.INSPECT FUSE (RR HTR)
a.
E161570E13
0.729,2.719 0.844,2.844 0.115,0.125 0.781,2.854 1.156,4.146 false 0.156,0.333 1.99,0.563 1.833,0.229 10 false Engine Room Relay Block: 0.844,4.135 1.417,4.292 0.573,0.156 10 false RR HTR

Remove the RR HTR fuse from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
RR HTR fuse Always Below 1 Ω



c.

Reinstall the RR HTR fuse.



OK

3.INSPECT REAR BLOWER MOTOR (SYSTEM VOLTAGE)

NG

REPLACE FUSE

3.INSPECT REAR BLOWER MOTOR (SYSTEM VOLTAGE)
a.
U154100E02
0.094,0.104 2.417,0.448 2.323,0.344 10 false Front view of wire harness connector: (to Rear Blower Motor) 0.51,1.469 0.802,1.615 0.292,0.146 10 false P10

Disconnect the P10 rear blower motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
P10-2 - Body ground Always 11 to 14 V



c.

Reconnect the rear blower motor connector.



OK

4.INSPECT REAR BLOWER MOTOR

NG

5.CHECK HARNESS AND CONNECTOR (REAR BLOWER MOTOR - REAR BLOWER MOTOR CONTROL, BODY GROUND)
4.INSPECT REAR BLOWER MOTOR
a.
E162302E03
0.084,0.037 2.596,0.378 2.512,0.340 10 Component without harness connected: (Rear Blower Motor)

Remove rear blower motor (See page Vehicle Interior>HEATING / AIR CONDITIONING>REAR BLOWER MOTOR>REMOVAL).


b.

Check the rear blower motor.

OK:
Tester Connection Specified Condition
Battery positive (+) → 2
Battery negative (-) → 1
The rear blower motor operates smoothly.



c.

Reinstall the rear blower motor.



OK

5.CHECK HARNESS AND CONNECTOR (REAR BLOWER MOTOR - REAR BLOWER MOTOR CONTROL, BODY GROUND)

NG

5.CHECK HARNESS AND CONNECTOR (REAR BLOWER MOTOR - REAR BLOWER MOTOR CONTROL, BODY GROUND)
a.
U154061E02
1.99,3.844 2.375,3.938 true 0.198,0.094 2.583,0.448 2.385,0.354 10 false Front view of wire harness connector: (to Rear Blower Motor) 0.198,2.26 2.583,2.615 2.385,0.354 10 false Front view of wire harness connector: (to Rear Blower Motor Control) 2.427,3.854 2.813,4.063 0.385,0.208 10 false VM 0.375,1.396 0.677,1.542 0.302,0.146 10 false P10 0.406,3.781 0.708,3.927 0.302,0.146 10 false P11

Disconnect the P10 rear blower motor connector.


b.

Disconnect the P11 rear blower motor control connector.


c.

Measure the resistance according the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P10-2 - P11-2 (VM) Always Below 1 Ω
P10-1 - Body ground Always Below 1 Ω
P10-2 - Body ground Always 10 kΩ or higher



d.

Reconnect the rear blower motor control connector.


e.

Reconnect the rear blower motor connector.



OK

6.CHECK HARNESS AND CONNECTOR (REAR BLOWER MOTOR CONTROL - FUSE, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (REAR BLOWER MOTOR CONTROL - FUSE, BODY GROUND)
a.
U154060E01
0.253,0.309 2.617,0.748 2.364,0.439 10 Front view of wire harness connector: (to Rear Blower Motor Control) 2.387,2.604 2.746,2.776 0.359,0.172 10 GND 0.641,2.604 0.869,2.784 0.228,0.179 10 +B 0.902,2.648 1.472,2.328 false 1.978,2.567 2.325,2.691 false 0.638,2.112 0.917,2.269 0.279,0.157 10 P11

Disconnect the P11 rear blower motor control connector.


b.

Measure the resistance and voltage according the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P11-6 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Switch Condition Specified Condition
P11-1 (+B) - Body ground Ignition switch ON 11 to 14 V



c.

Reconnect the rear blower motor control connector.



OK

7.CHECK HARNESS AND CONNECTOR (REAR BLOWER MOTOR CONTROL - AIR CONDITIONING AMPLIFIER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (REAR BLOWER MOTOR CONTROL - AIR CONDITIONING AMPLIFIER)
a.

Disconnect the P11 rear blower motor control connector.

E345216E01
1.708,1.938 2.073,2.219 0.365,0.281 4.458,1.313 4.823,1.594 0.365,0.281 0.833,2.385 0.948,2.083 true 5.115,1.875 5.385,1.573 true 0.875,0.156 3.115,0.729 2.24,0.573 10 false Rear view of wire harness connector: (to Air Conditioning Amplifier) 4.552,0.125 6.792,0.698 2.24,0.573 10 false Rear view of wire harness connector: (to Rear Blower Motor Control) 0.646,2.406 1.26,2.604 0.615,0.198 10 false BLWH 1.781,1.99 2.24,2.188 0.458,0.198 10 false H67 4.521,1.365 4.979,1.563 0.458,0.198 10 false P11 5.021,1.896 5.333,2.094 0.313,0.198 10 false SI


b.

Disconnect the H67 air conditioning amplifier connector.


c.

Measure the resistance according the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P11-3 (SI) - H67-22 (BLWH) Always Below 1 Ω
P11-3 (SI) - Body ground Always 10 kΩ or higher



d.

Reconnect the air conditioning amplifier connector.


e.

Reconnect the rear blower motor control connector.



OK

8.INSPECT REAR BLOWER MOTOR CONTROL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT REAR BLOWER MOTOR CONTROL
a.
U153944E02
0.438,2.448 0.688,3.042 true 0.594,2.448 1.333,3.042 true 0.74,2.979 1.156,3.156 0.417,0.177 10 false BLWH 0.135,0.083 2.531,0.458 2.396,0.375 10 false Rear view of wire harness connector:(Air Conditioning Amplifier) 1.427,2.271 1.708,2.448 0.281,0.177 10 false H67 1.385,2.958 1.938,3.135 0.552,0.177 10 false RGND

Disconnect the H67 air conditioning amplifier connector.


b.

Measure the voltage according the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H67-22 (BLWH) - H67-20 (RGND) Ignition switch ON
Rear blower motor switch OFF
4.5 to 5.5 V



c.

Reconnect the air conditioning amplifier connector.



OK

9.INSPECT AIR CONDITIONING AMPLIFIER

NG

9.INSPECT AIR CONDITIONING AMPLIFIER
a.

Remove the air conditioning amplifier with its connectors still connected (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).

E345217E01
0.844,0.646 1.281,0.906 0.438,0.26 0.948,1.927 0.865,1.365 true 1.542,1.906 0.979,1.365 true 0.51,0.073 2.76,0.771 2.25,0.698 10 false Component with harness connected: (Air Conditioning Amplifier) 0.948,0.698 1.406,0.896 0.458,0.198 10 false H67 0.875,1.938 1.49,2.135 0.615,0.198 10 false BLWH 1.49,1.938 2.104,2.135 0.615,0.198 10 false RGND 4.021,0.219 5.396,0.417 1.375,0.198 10 false Waveform: 4.208,0.469 6.333,0.75 2.125,0.281 10 false Rear Blower Motor Control Signal 6.104,0.813 6.698,1.042 0.594,0.229 10 false 1 V/DIV. 6.229,2 6.823,2.229 0.594,0.229 10 false GND 4.698,2.333 5.667,2.563 0.969,0.229 10 false 500 μsec./DIV.


b.

Check the waveform of the air conditioning amplifier connector.

Tester Connection BLWH - RGND
Tool Setting 1 V/DIV., 500 μsec./DIV.
Condition Ignition switch ON
Blower switch LO



OK

NG