Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM27L0U _58 Vehicle Interior _049344 HEATING / AIR CONDITIONING _0235901 AIR CONDITIONING SYSTEM J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  Air Conditioning Compressor Magnetic Clutch Circuit  


DESCRIPTION

When the air conditioning amplifier is turned on, a magnetic clutch ON signal is sent from the MGC terminal of the air conditioning amplifier. Then, the magnetic clutch relay (MG CLT) turns on to operate the magnetic clutch.

WIRING DIAGRAM

E146216E02
5.332,2.631 6.964,2.801 1.631,0.170 10 Air Conditioning Amplifier 5.514,1.551 5.896,1.720 0.381,0.170 10 MGC 4.786,3.662 5.167,3.831 0.381,0.170 10 MG+ 2.469,1.911 3.075,2.081 0.606,0.170 10 MG CLT 1.156,3.994 1.705,4.164 0.549,0.170 10 A/C IG 2.576,4.169 3.956,4.339 1.380,0.170 10 from IG1 No. 2 Relay 4.967,4.169 6.095,4.339 1.128,0.170 10 Magnetic Clutch 1.914,2.517 3.660,2.687 1.745,0.170 10 Engine Room Relay Block 5.332,2.456 5.644,2.626 0.312,0.170 10 H24 4.473,5.237 6.500,5.407 2.027,0.170 10 Air Conditioning Compressor 4.473,5.062 4.785,5.232 0.312,0.170 10 D39 5.18,1.438 5.416,1.608 0.236,0.170 10 20 3.746,1.539 3.878,1.709 0.132,0.170 10 1 1.691,1.539 1.823,1.709 0.132,0.170 10 1 3.746,1.04 3.878,1.210 0.132,0.170 10 1 3.204,1.427 3.336,1.597 0.132,0.170 10 2 3.204,0.928 3.336,1.097 0.132,0.170 10 3 4.754,3.412 4.886,3.582 0.132,0.170 10 3 4.543,3.849 4.675,4.019 0.132,0.170 10 1 1.691,1.04 1.823,1.210 0.132,0.170 10 1 2.222,1.427 2.354,1.597 0.132,0.170 10 1 2.222,0.928 2.354,1.097 0.132,0.170 10 5

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Connect the Techstream to DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Select "Communication Bus Check"

OK:

All ECUs and sensors connected to the CAN communication system are displayed.




OK

2.READ VALUE USING TECHSTREAM (A/C SIGNAL)

NG

2.READ VALUE USING TECHSTREAM (A/C SIGNAL)
a.

Connect the Techstream to DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / A/C Signal


e.

According to the display on the Techstream, read the Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
A/C Signal Air conditioning switch signal /
ON or OFF
ON: Air conditioning ON
OFF: Air conditioning OFF
-

OK:

The display is as specified in the normal condition.




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.INSPECT FUSE (A/C IG)
3.INSPECT FUSE (A/C IG)
a.
E345212E01
1.635,1.708 1.552,1.125 true 0.323,0.094 2.469,0.292 2.146,0.198 10 false Main Body ECU: 1.427,1.74 3.26,2.01 1.833,0.271 10 false A/C IG

Remove the A/C IG fuse from the main body ECU.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A/C IG fuse Always Below 1 Ω



c.

Reinstall the A/C IG fuse.



OK

4.INSPECT MAGNETIC CLUTCH RELAY (MG CLT)

NG

REPLACE FUSE

4.INSPECT MAGNETIC CLUTCH RELAY (MG CLT)
A378301E02
1.698,0.448 1.99,0.729 false 2.635,0.708 2.906,0.438 false 2.51,1.125 2.896,0.99 false 2.51,1.615 2.896,1.677 false 0.219,0.771 0.375,0.969 0.156,0.198 10 false 3 1.198,0.771 1.354,0.969 0.156,0.198 10 false 5 0.24,1.313 0.396,1.51 0.156,0.198 10 false 2 1.208,1.302 1.365,1.5 0.156,0.198 10 false 1 1.573,0.313 1.729,0.51 0.156,0.198 10 false 1 2.948,0.313 3.104,0.51 0.156,0.198 10 false 2 2.969,0.927 3.125,1.125 0.156,0.198 10 false 5 2.948,1.604 3.104,1.802 0.156,0.198 10 false 3

a.

Remove the magnetic clutch relay from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 When battery voltage is not applied between terminals 1 and 2 10 kΩ or higher
When battery voltage is applied to terminals 1 and 2 Below 1 Ω



c.

Reinstall e the magnetic clutch relay.



OK

5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY)

NG

REPLACE MAGNETIC CLUTCH RELAY

5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY)
U153927E01
0.757,2.787 1.129,2.946 0.372,0.159 10 MGC 1.364,2.099 1.023,2.761 false 0.306,0.021 2.650,0.345 2.344,0.324 10 Rear view of wire harness connector: (to Air Conditioning Amplifier) 1.676,0.854 1.966,1.013 0.290,0.159 10 H24

a.

Disconnect the H24 air conditioning amplifier connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H24-20 (MGC) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V




OK

6.CHECK AIR CONDITIONING AMPLIFIER (MGC VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK AIR CONDITIONING AMPLIFIER (MGC VOLTAGE)
U153929E02
1.333,1.479 1.333,2.333 true 1.167,2.354 1.531,2.531 0.365,0.177 10 false MGC 0.333,0.063 2.594,0.385 2.26,0.323 10 false Component with harness connector: (Air Conditioning Amplifier) 1.844,0.875 2.135,1.031 0.292,0.156 10 false H24

a.

Reconnect the H24 air conditioning amplifier connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H24-20 (MGC) - Body ground Engine running and air conditioning switch ON Below 1 V
Engine running and air conditioning switch OFF 11 to 14 V




OK

7.INSPECT AIR CONDITIONING COMPRESSOR (COMPRESSOR HARNESS)

NG

7.INSPECT AIR CONDITIONING COMPRESSOR (COMPRESSOR HARNESS)
E146414E01
0.158,0.121 2.640,0.430 2.482,0.309 10 Component without harness connected: (Air Conditioning Compressor) 0.158,2.674 2.633,2.982 2.475,0.309 10 Component without harness connected: (Magnetic Clutch) 1.722,1.738 2.377,2.065 false 2.395,1.99 2.753,2.174 0.357,0.184 10 MG+

a.

Disconnect the D39 air conditioning compressor connector.


b.

Disconnect the magnetic clutch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (MG+) - 1 Always Below 1 Ω
3 (MG+) - Body ground Always 10 kΩ or higher




OK

8.INSPECT MAGNETIC CLUTCH

NG

REPAIR AIR CONDITIONING COMPRESSOR

8.INSPECT MAGNETIC CLUTCH
a.
E146516E01
0.223,0.397 2.775,0.747 2.552,0.350 10 Component without harness connected: (Magnetic Clutch)

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - Body ground Always 3.4 to 3.8 Ω



b.

When connector terminal 1 is connected to the positive (+) battery terminal, check that the following occurs: 1) the magnetic clutch operating sound can be heard, and 2) the magnetic clutch hub and rotor lock.


c.

Reconnect the air conditioning compressor connector.


d.

Reconnect the magnetic clutch connector.



OK

9.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING COMPRESSOR - ENGINE ROOM RELAY BLOCK)

NG

9.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING COMPRESSOR - ENGINE ROOM RELAY BLOCK)
E345213E01
0.698,1.281 1.115,1.531 0.417,0.25 1.25,1.938 1.667,1.521 true 5.49,2.448 5.74,2.208 true 0.615,0.115 2.906,0.708 2.292,0.594 10 false Front view of wire harness connector: (to Air Conditioning Compressor) 4.208,0.115 6.5,0.708 2.292,0.594 10 false Component without relay connected: (Engine Room Relay Block) 0.792,1.323 1.25,1.521 0.458,0.198 10 false D39 1.104,1.948 1.563,2.146 0.458,0.198 10 false MG+ 4.229,2.458 6.292,2.76 2.063,0.302 10 false Magnetic Clutch Relay (MG CLT)

a.

Disconnect the D39 air conditioning compressor connector.


b.

Remove the magnetic clutch relay (MG CLT) from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D39-3 (MG+) - Engine room relay block magnetic clutch relay terminal 3 Always Below 1 Ω
D39-3 (MG+) or Engine room relay block magnetic clutch relay terminal 3 - Body ground Always 10 kΩ or higher



d.

Reinstall the magnetic clutch relay (MG CLT).


e.

Reconnect the air conditioning compressor connector.



OK

10.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - BATTERY)
E146416E01
0.18,0.079 2.650,0.570 2.471,0.492 10 Component without relay connected: (Engine Room Relay Block) 2.388,2.617 2.207,2.87 false 0.741,2.861 2.842,3.066 2.100,0.205 10 Magnetic Clutch Relay (MG CLT)

a.

Remove the magnetic clutch relay (MG CLT) from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Engine room relay block magnetic clutch relay terminal 5 - Body ground Ignition switch ON 11 to 14 V



c.

Reinstall the magnetic clutch relay.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR