Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING
RM27L0U _58 Vehicle Interior _049346 INTERIOR PANELS / TRIM _0235933 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 58408D 3.REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY

B190118

a.

Raise the handle, disengage the 4 guides and remove the No. 2 deck board.


Hide 64429G 4.REMOVE LUGGAGE COMPARTMENT TRIM BOX

B194633

a.

Remove the 4 caps.


b.
B190116

Remove the 4 bolts and luggage compartment trim box.


Hide 66310D 5.REMOVE ROPE HOOK ASSEMBLY

B191405

a.

Remove the bolt and rope hook.

HINT:

Use the same procedure for both sides.



Hide 58401A 6.REMOVE NO. 1 DECK BOARD SUB-ASSEMBLY

B190117

a.

Disengage the 5 clips and remove the No. 1 deck board.


Hide 58403K 7.REMOVE DECK BOARD REINFORCEMENT SUB-ASSEMBLY

B190120

a.

Remove the 4 bolts and deck board reinforcement.


Hide 58417F 8.REMOVE DECK BOARD BRACKET

B190119

a.

Remove the 2 bolts and deck board bracket.


Hide 9.REMOVE REAR NO. 2 SEAT ASSEMBLY RH

a.

for Manual Seat:

Remove the rear No. 2 seat assembly RH (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY(for Manual Seat Type RH Side)>REMOVAL).


b.

for Power Seat:

Remove the rear No. 2 seat assembly RH (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY(for Power Seat Type RH Side)>REMOVAL).


Hide 10.REMOVE REAR NO. 2 SEAT ASSEMBLY LH

a.

for Manual Seat:

Remove the rear No. 2 seat assembly LH (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY(for Manual Seat Type LH Side)>REMOVAL).


b.

for Power Seat:

Remove the rear No. 2 seat assembly LH (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY(for Power Seat Type LH Side)>REMOVAL).


Hide 67913B 11.REMOVE FRONT DOOR SCUFF PLATE RH

B190151

a.

Detach the 9 claws and remove the scuff plate.


Hide 67914B 12.REMOVE FRONT DOOR SCUFF PLATE LH

HINT:

Use the same procedure for both sides.


Hide 62111C 13.REMOVE COWL SIDE TRIM BOARD RH

B190152

a.

Remove the clip.


b.

Disengage the 2 clips and remove the cowl side trim board.


Hide 62112 14.REMOVE COWL SIDE TRIM BOARD LH

HINT:

Use the same procedure for both sides.


Hide 62311B 15.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

B191803

a.

Remove the front door opening trim weatherstrip.


Hide 62312B 16.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:

Use the same procedure for both sides.


Hide 71693 17.REMOVE REAR SEAT CUSHION HINGE LOWER COVER RH

B191794

a.

Disengage the 2 clips and 5 claws, and remove the rear seat cushion hinge lower cover.


Hide 71694 18.REMOVE REAR SEAT CUSHION HINGE LOWER COVER LH

HINT:

Use the same procedure for both sides.


Hide 51775 19.REMOVE REAR FLOOR STEP NO. 1 COVER

B191403E02
1.719,1.729 1.302,1.531 false 1.76,1.667 2.813,1.906 1.052,0.24 10 true Protective Tape

a.

Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the cap.

HINT:

Use the same procedure for both sides.



Hide 20.REMOVE REAR FLOOR STEP NO. 2 COVER

B193052E02
2.125,1.823 1.771,1.042 false 2.01,1.844 3.01,2.104 1,0.26 10 true Protective Tape

a.

Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the cap.

HINT:

Use the same procedure for both sides.



Hide 67917C 21.REMOVE REAR DOOR SCUFF PLATE RH

B186665

a.

Remove the bolt.


b.

Disengage the 5 clips and the 6 claws and 2 guides, and remove the rear door scuff plate front side.


c.
B186666

Remove the 2 bolts.


d.

Disengage the 5 clips and 2 claws, and remove the scuff plate rear side.


Hide 67918D 22.REMOVE REAR DOOR SCUFF PLATE LH

HINT:

Use the same procedure for both sides.


Hide 62331C 23.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

B191804

a.

Remove the rear door opening trim weatherstrip.


Hide 62332C 24.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:

Use the same procedure for both sides.


Hide 62211 25.REMOVE FRONT PILLAR GARNISH RH

a.

Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the 2 assist grip plugs.


b.

Remove the 2 bolts and assist grip.


c.

Detach the claw and remove the front pillar garnish.

B190131E02
1.719,0.927 2.448,0.583 false 2.479,0.51 3.5,0.688 1.021,0.177 10 false Protective Tape


d.
B190132E02
1.99,1.24 1.688,1.229 false 1.375,0.156 2.125,0.375 false 1.281,0.573 1.646,0.594 false 0.375,0.49 1.333,0.667 0.958,0.177 10 false Adhesive Tape 0.375,0.063 1.427,0.229 1.052,0.167 10 false Protective cover 2.01,1.156 3.094,1.583 1.083,0.427 10 true Curtain Shield Airbag Assembly

Protect the curtain shield airbag.

i.

Thoroughly cover the airbag with a cloth or nylon sheet and fix the ends of the cover with adhesive tape, as shown in the illustration.

NOTICE:

Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.




Hide 62212 26.REMOVE FRONT PILLAR GARNISH LH

HINT:

Use the same procedure for both sides.


Hide 62413A 27.REMOVE LOWER CENTER PILLAR GARNISH RH

B190128

a.

Disengage the 3 claws and remove the outer lap belt anchor cover.


b.
B190129

Remove the bolt and outer lap belt anchor.


c.
B190125

Disengage the 7 clips and 2 claws, and remove the center pillar garnish.


Hide 62414A 28.REMOVE LOWER CENTER PILLAR GARNISH LH

HINT:

Use the same procedure for both sides.


Hide 62411 29.REMOVE CENTER PILLAR GARNISH RH

a.

Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the 2 assist grip plugs.


b.

Remove the 2 bolts and assist grip.


c.

Remove the bolt.


d.

Disengage the clip and guide.


e.

Pass the front seat outer belt floor anchor through the center pillar garnish, and remove the center pillar garnish.

B190130E02
2.458,0.135 1.938,0.802 false 2.5,0.073 3.521,0.271 1.021,0.198 10 false Protective Tape


Hide 62412 30.REMOVE CENTER PILLAR GARNISH LH

HINT:

Use the same procedure for both sides.


Hide 66310D 31.REMOVE ROPE HOOK ASSEMBLY

B190140E02
2.083,0.615 1.885,0.615 false 2.135,0.542 3.135,0.75 1,0.208 10 true Protective Tape

HINT:

Use the same procedure for both sides.


a.

Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the cover.


b.
B190141

Remove the bolt and rope hook.


Hide 58573A 32.REMOVE REAR FLOOR MAT SUPPORT PLATE

B190142

a.

Disengage the 5 clips and 4 claws, and remove the rear floor mat support plate.


Hide 62510P 33.REMOVE QUARTER TRIM PANEL ASSEMBLY RH

B190145

a.

Disengage the 3 claws and remove the outer lap belt anchor cover.


b.
B190158

Remove the bolt and outer lap belt anchor.


c.
B190146

Remove the bolt and outer lap belt anchor.


d.
B190148E02
1.865,1.646 2.052,1.208 false 1.302,1.656 2.323,1.875 1.021,0.219 10 true Protective Tape

Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the cover.


e.

Remove the 2 bolts and 2 clips.


f.

Disengage the 11 clips.


g.

Disconnect the connector and remove the quarter trim panel.

B219907


Hide 62520P 34.REMOVE QUARTER TRIM PANEL ASSEMBLY LH

B193920

a.

Disengage the 3 claws and remove the outer lap belt anchor cover.


b.
B191818

Remove the bolt and outer lap belt anchor.


c.
B191816

Remove the bolt and outer lap belt anchor.


d.
B191817E02
1.604,1.625 1.51,1.167 false 1.135,1.667 2.167,1.927 1.031,0.26 10 true Protective Tape

Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the cover.


e.

Remove the 2 bolts and 2 clips.


f.

Disengage the 11 clips.


g.

Disconnect the connector and remove the quarter trim panel.

B222458


Hide 62510P 35.REMOVE QUARTER TRIM PANEL ASSEMBLY RH (for Power Seat)

B190145

a.

Disengage the 3 claws and remove the outer lap belt anchor cover.


b.
B190158

Remove the bolt and outer lap belt anchor.


c.
B190146

Remove the bolt and outer lap belt anchor.


d.
B190148E02
1.865,1.646 2.052,1.208 false 1.302,1.656 2.323,1.875 1.021,0.219 10 true Protective Tape

Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the cover.


e.

Remove the 2 bolts and 2 clips.


f.

Disengage the 11 clips.


g.

Disconnect the 3 connectors and remove the quarter trim panel.

B222459


Hide 62520P 36.REMOVE QUARTER TRIM PANEL ASSEMBLY LH (for Power Seat)

B193920

a.

Disengage the 3 claws and remove the outer lap belt anchor cover.


b.
B191818

Remove the bolt and outer lap belt anchor.


c.
B191816

Remove the bolt and outer lap belt anchor.


d.
B191817E02
1.604,1.625 1.51,1.167 false 1.135,1.667 2.167,1.927 1.031,0.26 10 true Protective Tape

Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the cover.


e.

Remove the 2 bolts and 2 clips.


f.

Disengage the 2 clamps and remove the wire harness.


g.

Disengage the 11 clips and 2 clamps.


h.

Disconnect the 3 connectors and remove the quarter trim panel.

B222460


Hide 62550F 37.REMOVE REAR WINDOW SIDE GARNISH ASSEMBLY RH

B190121E03
2.323,0.906 2.646,1.552 false 2.229,1.563 3.281,1.823 1.052,0.26 10 true Protective Tape

a.

Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the cover.


b.
B190124

Remove the bolt.


c.

Detach the 5 clips.


d.

Pass the rear seat outer belt floor anchor through the rear window side garnish, and remove the rear window side garnish.


Hide 62560C 38.REMOVE REAR WINDOW SIDE GARNISH ASSEMBLY LH

HINT:

Use the same procedure for both sides.


Hide 62570D 39.REMOVE REAR WINDOW NO. 2 SIDE GARNISH ASSEMBLY RH

B190122E02
2.625,1.292 2.427,0.719 false 2.25,1.302 3.26,1.479 1.01,0.177 10 false Protective Tape

a.

Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the cover.


b.
B190123

Remove the bolt.


c.

Disengage the 5 clips.


d.

Pass the rear seat outer belt floor anchor through the rear window No. 2 side garnish, and remove the rear window No. 2 side garnish.


Hide 62580F 40.REMOVE REAR WINDOW NO. 2 SIDE GARNISH ASSEMBLY LH (w/o Power Back Door)

HINT:

Use the same procedure for both sides.


Hide 62580F 41.REMOVE REAR WINDOW NO. 2 SIDE GARNISH ASSEMBLY LH (w/ Power Back Door)

B191819E02
0.625,1.177 0.99,0.698 false 0.156,1.198 1.156,1.406 1,0.208 10 false Protective Tape

a.

Using a screwdriver, disengage the claw and remove the cover.


b.
B191798

Remove the bolt.


c.

Disengage the 5 clips.


d.

Disconnect the connector.


e.

Pass the rear seat outer belt floor anchor through the rear window No. 2 side garnish, and remove the rear window No. 2 side garnish.


Hide 63650A 42.REMOVE ROOF CONSOLE BOX ASSEMBLY

a.

for Short Type:

Remove the roof console box (See page Vehicle Interior>INTERIOR PANELS / TRIM>OVERHEAD CONSOLE BOX>REMOVAL).


b.

for Long Type:

Remove the roof console box (See page Vehicle Interior>INTERIOR PANELS / TRIM>OVERHEAD CONSOLE BOX>REMOVAL).


Hide 81240 43.REMOVE NO. 1 ROOM LIGHT ASSEMBLY

a.

Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the lens.


b.

Using a moulding remover D, disengage the 4 clips.


c.

Disconnect the connector and then remove the No. 1 room light assembly.

B190138E01
1.415,1.526 2.425,1.720 1.009,0.194 10 Protective Tape 1.362,1.581 1.086,1.258 false 1.521,2.033 2.874,2.229 1.353,0.196 10 Moulding Remover D 3.262,1.846 2.885,2.106 false


Hide 44.REMOVE NO. 1 ROOM LIGHT ASSEMBLY (w/ Rear Seat Entertainment System)

B193035E03
0.49,2.323 0.49,1.229 false 0.24,2.323 0.979,2.677 0.74,0.354 10 false Moulding Remover D

a.

Using a moulding remover D, disengage the 4 clips.


b.
B191797

Disconnect the connector and then remove the No. 1 room light assembly.


Hide 81240D 45.REMOVE NO. 2 ROOM LIGHT ASSEMBLY

a.

Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the lens.


b.

Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws.


c.

Disconnect the connector and then remove the No. 2 room light assembly.

B190137E01
0.515,2.007 1.536,2.189 1.020,0.181 10 Protective Tape 2.842,1.73 3.862,1.911 1.020,0.181 10 Protective Tape 0.935,1.179 0.967,1.977 false 4.465,1.305 3.854,1.804 false


Hide 74317 46.REMOVE VISOR BRACKET COVER RH

B190134E02
1.708,0.125 1.604,0.375 false 1.729,0.042 3.052,0.229 1.323,0.188 10 false Moulding Remover B

a.

Using a moulding remover B with its tip wrapped in protective tape, disengage the 4 claws and remove the visor bracket cover.


Hide 74318 47.REMOVE VISOR BRACKET COVER LH

HINT:

Use the same procedure for both sides.


Hide 74310 48.REMOVE VISOR ASSEMBLY RH (w/o Illumination)

B190135

a.

Remove the 3 screws and visor.


Hide 74320 49.REMOVE VISOR ASSEMBLY LH (w/o Illumination)

HINT:

Use the same procedure for both sides.


Hide 74310 50.REMOVE VISOR ASSEMBLY RH (w/ Illumination)

B190133

a.

Remove the 4 screws.


b.
B191402

Disconnect the connector and then remove the visor.


Hide 74320 51.REMOVE VISOR ASSEMBLY LH (w/ Illumination)

HINT:

Use the same procedure for both sides.


Hide 74610A 52.REMOVE ASSIST GRIP SUB-ASSEMBLY

B190149E02
1.177,1.313 1.656,0.531 false 0.281,1.313 1.281,1.594 1,0.281 10 true Protective Tape

HINT:

Use the same procedure for both sides.


a.

Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the 2 assist grip covers.


b.

Disengage the 2 clips and remove the assist grip.


Hide 74617Y 53.REMOVE ASSIST GRIP PLUG

B190150E01
0.338,1.044 1.247,1.210 0.909,0.166 10 Service Notch 2.178,0.011 3.190,0.187 1.012,0.176 10 Protective Tape 2.115,0.087 1.757,0.475 false 0.592,0.823 0.928,1.044 false

a.

Insert a screwdriver with its tip wrapped in protective tape, into the service notch and break off the cap.


b.

Disengage the clip and remove the assist grip plug.


Hide 63379 54.REMOVE ROOF HEADLINING REAR TRIM COVER LH

B191406E02
0.823,0.917 1.24,1 false 0.208,0.813 0.813,1.271 0.604,0.458 10 true Moulding Remover D

a.

Using a moulding remover D, disengage the 6 claws and remove the roof headlining rear trim cover.


Hide 87834 55.REMOVE REAR VIEW INNER MIRROR STAY HOLDER COVER (w/ EC Mirror)

Hide 63310 56.REMOVE ROOF HEADLINING ASSEMBLY (w/o Rear Seat Entertainment System)

B190163

a.

Disconnect the connector.


b.

Remove the washer hose and amplifier antenna.


c.
B190155

Disconnect the connector.


d.

Disengage the 3 clamps and remove the roof wire.


e.
B190127

Disconnect the connector.


f.

Remove the bolt.


g.

Disengage the 4 clamps and remove the amplifier antenna.


h.
B190126

Disconnect the connector.


i.

Remove the bolt and amplifier antenna.


j.

Disconnect the satellite radio antenna connector.


k.
B190136

Remove the screw and visor holder.

HINT:

Use the same procedure to remove the visor holder on the other side.



l.

Disengage the clip.


m.

Remove the washer hose and the roof headlining.

B191826


n.
B193054

Take out the roof headlining from the cabin as shown in the illustration.

NOTICE:

Be careful not to damage the roof headlining when taking it out.



Hide 57.REMOVE ROOF HEADLINING ASSEMBLY (w/ Rear Seat Entertainment System)

B190163

a.

Disconnect the connector.


b.

Remove the washer hose and amplifier antenna.


c.
B193939

Disconnect the 2 connectors.


d.

Disengage the 3 clamps and remove the roof wire.


e.
B191400

Disconnect the connector.


f.

Disengage the clamp and remove the wire harness.


g.
B190127

Disconnect the connector.


h.

Remove the bolt.


i.

Disengage the 4 clamps and remove the amplifier antenna.


j.
B190126

Disconnect the connector.


k.

Remove the bolt and amplifier antenna.


l.
B190136

Remove the screw and visor holder.

HINT:

Use the same procedure to remove the visor holder on the other side.



m.

Disengage the clip.


n.

Remove the washer hose and the roof headlining.

B191826


o.
B193054

Take out the roof headlining from the cabin as shown in the illustration.

NOTICE:

Be careful not to damage the roof headlining when taking it out.



Hide 58.REMOVE ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)

B190163

a.

Disconnect the connector.


b.

Remove the washer hose and amplifier antenna.


c.
B191808

Disconnect the 3 connectors.


d.

Disengage the 3 clamps and remove the roof wire.


e.
B191401

Disconnect the connector.


f.
B190127

Disconnect the connector.


g.

Remove the bolt.


h.

Disengage the 4 clamps and remove the amplifier antenna.


i.
B190126

Disconnect the connector.


j.

Remove the bolt and amplifier antenna.


k.

Disengage the clip and 14 fasteners.


l.

Remove the washer hose and the roof headlining.

B191820


m.
B193053

Take out the roof headlining from the cabin as shown in the illustration.