Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM27L0U _59 Vehicle Exterior _049347 WINDOW / GLASS _0235939 POWER WINDOW CONTROL SYSTEM C

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  B2221  Jam Protection Pulse Sensor Circuit on Back Door  


DESCRIPTION

The back door ECU monitors the condition of the power window motor and detects the position of the door glass by using pulse signals output from the 2 pulse sensors in the power window motor.

DTC Code DTC Detection Condition Suspected Part
B2221
·

PLS1 pulse sensor circuit malfunction

·

PLS2 pulse sensor circuit malfunction

·

Pulse direction is opposite to motor rotating direction (Short circuit between PLS1 and PLS2)

·

PLS1 and PLS2 pulse sensors circuit malfunction

·

Fully closed position is misaligned


·

Back door Power window regulator motor

·

Back door ECU

·

Harness or connector



FAIL-SAFE

If the pulse sensor in the back door power window regulator motor malfunctions (DTC B2221 is output), the power window functions will be restricted:

·

The AUTO UP/ DOWN function is disabled.

·

The MANUAL UP/DOWN function via the back door power window switch can be performed with the ignition switch ON.

·

The MANUAL UP/DOWN function via the back door lock key cylinder can be performed with the ignition switch ON.


WIRING DIAGRAM

B178351E01
0.689,1.114 1.160,1.268 0.471,0.153 10 Hall-IC 0.689,1.913 1.160,2.067 0.471,0.153 10 Hall-IC 2.578,0.719 3.004,0.863 0.426,0.144 10 SSRB 2.597,1.143 2.957,1.292 0.360,0.149 10 PLS1 2.597,1.92 2.974,2.064 0.377,0.143 10 PLS2 2.589,2.251 2.986,2.402 0.396,0.151 10 LMTE 5.67,0.834 5.998,0.990 0.328,0.156 10 DSV 5.67,1.242 5.971,1.407 0.301,0.165 10 DS1 5.67,2 5.998,2.156 0.328,0.156 10 DS2 5.67,2.341 6.018,2.506 0.348,0.165 10 DSG 3.069,0.712 3.174,0.866 0.105,0.153 10 4 3.069,1.149 3.174,1.310 0.105,0.161 10 3 3.069,1.884 3.182,2.046 0.113,0.161 10 5 3.069,2.252 3.170,2.413 0.101,0.161 10 6 5.383,0.723 5.588,0.877 0.204,0.154 10 12 5.395,1.127 5.576,1.288 0.181,0.161 10 13 5.393,1.885 5.578,2.042 0.185,0.157 10 14 5.399,2.267 5.572,2.416 0.173,0.149 10 23 0.437,2.924 3.259,3.087 2.822,0.164 10 Back Door Power Window Regulator Motor 5.44,2.914 6.686,3.104 1.246,0.190 10 Back Door ECU 5.44,2.756 5.659,2.908 0.219,0.152 10 V3 0.437,2.762 0.728,2.917 0.291,0.155 10 V4

PROCEDURE

1.PERFORM INITIALIZATION (BACK DOOR POWER WINDOW REGULATOR MOTOR)
a.

Initialize the back door power window regulator motor (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).



NEXT

2.CHECK DTC
2.CHECK DTC

OK

END

NG

3.CHECK HARNESS AND CONNECTOR (BACK DOOR ECU - BACK DOOR POWER WINDOW REGULATOR MOTOR)
3.CHECK HARNESS AND CONNECTOR (BACK DOOR ECU - BACK DOOR POWER WINDOW REGULATOR MOTOR)
a.
U153208E02
0.781,2.25 1.688,2.01 false 2.813,1.177 1.844,1.948 true 2,1.948 2.844,1.583 true 1.979,2.198 2.896,2.083 true 0.885,4.531 1.375,4.302 false 2.375,3.708 1.604,4.271 true 1.844,4.25 2.49,4 false 2.052,4.313 2.469,4.271 true 0.125,0.073 2.469,0.417 2.344,0.344 10 false Front view of wire harness connector: (to Back Door ECU) 0.167,2.667 2.646,3.188 2.479,0.521 10 false Front view of wire harness connector: (to Back Door Power Window Regulator Motor) 0.385,2.167 0.719,2.323 0.333,0.156 10 false DSV 2.875,1.094 3.177,1.281 0.302,0.188 10 false DS1 2.875,1.51 3.198,1.698 0.323,0.188 10 false DS2 2.917,1.979 3.26,2.125 0.344,0.146 10 false DSG 2.406,3.625 2.833,3.771 0.427,0.146 10 false SSRB 0.448,4.438 0.813,4.583 0.365,0.146 10 false PLS1 2.542,3.906 2.917,4.052 0.375,0.146 10 false PLS2 2.5,4.177 2.896,4.323 0.396,0.146 10 false LMTE 0.448,1.594 0.656,1.781 0.208,0.188 10 false V3 0.5,4.01 0.771,4.167 0.271,0.156 10 false V4

Disconnect the V3 back door ECU connector.


b.

Disconnect the V4 back door power window regulator motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V3-12 (DSV) - V4-4 (SSRB) Always Below 1 Ω
V3-13 (DS1) - V4-3 (PLS1) Always Below 1 Ω
V3-14 (DS2) - V4-5 (PLS2) Always Below 1 Ω
V3-23 (DSG) - V4-6 (LMTE) Always Below 1 Ω
V3-12 (DSV) - Body ground Always 10 kΩ or higher
V3-13 (DS1) - Body ground Always 10 kΩ or higher
V3-14 (DS2) - Body ground Always 10 kΩ or higher
V3-23 (DSG) - Body ground Always 10 kΩ or higher



d.

Reconnect the back door power window regulator motor connector.


e.

Reconnect the back door ECU connector.



OK

4.REPLACE BACK DOOR POWER WINDOW REGULATOR MOTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE BACK DOOR POWER WINDOW REGULATOR MOTOR
a.

Replace back door power window regulator motor (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR>DISASSEMBLY).



NEXT

5.CHECK DTC
5.CHECK DTC

OK

END

NG

REPLACE BACK DOOR ECU