Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM27L0U _59 Vehicle Exterior _049347 WINDOW / GLASS _0235939 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Driver Side Power Window does not Operate with Power Window Master Switch  


DESCRIPTION

If the manual UP/DOWN function does not operate, there may be a malfunction in the power window regulator master switch, the power window regulator motor, the harness and connector.


WIRING DIAGRAM

B443133E01
0.958,0.458 1.594,0.667 0.635,0.208 10 false to Battery 1.833,0.656 2.375,1.01 0.542,0.354 10 false POWER No. 3 2.76,1.375 2.885,1.563 0.125,0.188 10 false 3 3.01,1.5 3.135,1.688 0.125,0.188 10 false B 2.771,1.844 2.896,2.031 0.125,0.188 10 false 6 2.99,2 3.302,2.188 0.313,0.188 10 false LIN1 3.031,2.917 3.156,3.104 0.125,0.188 10 false B 2.688,2.771 2.854,2.958 0.167,0.188 10 false 13 0.458,1.99 1.635,2.177 1.177,0.188 10 false to Main Body ECU 0.417,2.906 1.583,3.271 1.167,0.365 10 false to Main Body ECU (P/W Relay) 0.792,4.344 2.094,4.521 1.302,0.177 10 false : LIN Communication Line 2.573,3.885 2.802,4.073 0.229,0.188 10 false M2 2.563,4.083 4.146,4.448 1.583,0.365 10 false Power Window Regulator Master Switch Assembly 3.604,1.969 3.917,2.156 0.313,0.188 10 false LIN2 3.656,2.448 3.865,2.635 0.208,0.188 10 false UP 3.406,2.896 3.854,3.073 0.448,0.177 10 false DOWN 3.719,3.292 3.854,3.479 0.135,0.188 10 false E 4.031,1.813 4.156,2 0.125,0.188 10 false 7 4.052,2.302 4.177,2.49 0.125,0.188 10 false 4 4.042,2.74 4.167,2.927 0.125,0.188 10 false 5 4.052,3.156 4.177,3.344 0.125,0.188 10 false 1 5.281,0.333 5.406,0.521 0.125,0.188 10 false 2 5.583,0.469 5.708,0.656 0.125,0.188 10 false B 5.323,1.813 5.448,2 0.125,0.188 10 false 9 5.24,2.281 5.427,2.458 0.188,0.177 10 false 10 5.292,2.771 5.417,2.958 0.125,0.188 10 false 7 5.302,3.156 5.427,3.344 0.125,0.188 10 false 1 5.542,1.99 5.781,2.177 0.24,0.188 10 false LIN 5.573,2.438 5.781,2.625 0.208,0.188 10 false UP 5.542,2.885 5.99,3.063 0.448,0.177 10 false DOWN 5.583,3.271 5.885,3.469 0.302,0.198 10 false GND 5.063,3.906 5.292,4.094 0.229,0.188 10 false M3 5.063,4.073 6.979,4.427 1.917,0.354 10 false Front Power Window Regulator Motor Assembly LH

PROCEDURE

1.CHECK LIN COMMUNICATION SYSTEM
a.

Check for LIN communication system DTCs related to the power window control system (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

LIN communication system DTCs are not output.




OK

2.CHECK DTC (B2312)

NG

2.CHECK DTC (B2312)
a.

Check if DTC B2312 is output (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2312 is not output.




OK

3.READ VALUE USING TECHSTREAM (D-DOOR MOTOR)

NG

3.READ VALUE USING TECHSTREAM (D-DOOR MOTOR)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / D-Door Motor / Data List.


e.

According to the display on the Techstream, read the Data List.

D-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door P/W Up SW Driver side power window MANUAL UP switch signal / ON or OFF ON: Driver side power window manual UP switch operated
OFF: Driver side power window switch not operated
-
D Door P/W Down SW Driver side power window MANUAL DOWN switch signal / ON or OFF ON: Driver side power window manual DOWN switch operated
OFF: OFF: Driver side power window switch not operated
-


OK:

The Techstream display changes normally when master switch is operated.



OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - BATTERY, BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - BATTERY, BODY GROUND)
a.
U153210E02
1.313,2.042 1.167,2.719 true 1.563,2.313 1.802,2.729 true 0.865,2.021 0.521,2.479 true 0.385,0.021 2.75,0.51 2.365,0.49 10 false Front view of wire harness connector: (to Power Window Regulator Master Switch Assembly) 1.094,2.75 1.323,2.906 0.229,0.156 10 false B 1.74,2.75 2.219,2.906 0.479,0.156 10 false B 0.385,2.49 0.542,2.646 0.156,0.156 10 false E 0.219,1.708 0.438,1.885 0.219,0.177 10 false M2

Disconnect the M2 power window regulator master switch assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M2-3 (B) - Body ground Always 11 to 14 V
M2-13 (B) - Body ground Ignition switch ON 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
M2-1 (E) - Body ground Always Below 1 Ω



c.

Reconnect the power window regulator master switch assembly connector.



OK

5.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR LH - BATTERY, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR LH - BATTERY, BODY GROUND)
a.
U153212E01
0.261,0.038 2.738,0.572 2.477,0.534 10 Front view of wire harness connector: (to Front Power Window Regulator Motor Assembly LH) 0.69,2.124 1.040,2.281 0.350,0.157 10 GND 2.344,2.195 2.465,2.365 0.121,0.169 10 B 1.531,1.814 1.129,2.166 false 1.896,1.822 2.297,2.223 false 0.613,1.616 0.833,1.774 0.220,0.158 10 M3

Disconnect the M3 front power window regulator motor assembly LH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M3-2(B) - Body ground Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
M3-1(GND) - Body ground Always Below 1 Ω



c.

Reconnect the front power window regulator motor assembly LH connector.



OK

6.CHECK HARNESS AND CONNECTOR (POWER WINDOW MASTER SWITCH - FRONT POWER WINDOW MOTOR LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (POWER WINDOW MASTER SWITCH - FRONT POWER WINDOW MOTOR LH)
U153248E01
0.29,0.037 2.646,0.545 2.356,0.508 10 Front view of wire harness connector: (to Power Window Regulator Master Switch Assembly) 0.205,2.305 2.562,2.814 2.356,0.508 10 Front view of wire harness connector: (to Front Power Window Regulator Motor Assembly LH) 0.479,1.817 0.711,1.957 0.232,0.139 10 UP 2.637,1.817 3.096,1.969 0.459,0.152 10 DOWN 1.569,1.8 0.778,1.892 false 1.77,1.817 2.585,1.89 false 2.461,4.312 2.693,4.451 0.232,0.139 10 UP 0.462,4.3 0.921,4.452 0.459,0.152 10 DOWN 1.55,4.28 1.032,4.372 false 1.908,4.288 2.426,4.385 false 0.457,1.394 0.679,1.542 0.223,0.147 10 M2 0.739,3.716 0.962,3.864 0.223,0.147 10 M3

a.

Disconnect the M2 power window regulator master switch assembly connector.


b.

Disconnect the M3 front power window regulator motor assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M2-4 (UP) - M3-10 (UP) Always Below 1 Ω
M2-5 (DOWN) - M3-7 (DOWN) Always Below 1 Ω
M2-4 (UP) - Body ground Always 10 kΩ or higher
M2-5 (DOWN) - Body ground Always 10 kΩ or higher



d.

Reconnect the front power window regulator motor assembly LH connector.


e.

Reconnect the power window regulator master switch assembly connector.



OK

7.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
a.
B194348E02
1.648,3.008 2.307,3.159 0.659,0.151 10 Clockwise 1.849,2.628 2.965,2.785 1.116,0.157 10 Counterclockwise 0.071,0.055 2.541,0.544 2.471,0.489 10 Component without harness connected: (Front Power Window Regulator Motor Assembly LH)

Remove the front power window regulator motor assembly LH (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR>REMOVAL).


b.

Apply positive (+) battery voltage to the connector terminal 2(B).

NOTICE:
·

Do not apply positive (+) battery voltage to any terminals except terminal 2(B), to avoid damaging the pulse sensor inside the motor.

·

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.




c.

Apply negative (-) battery voltage to the connector terminals 1(GND) and 7 (DOWN) / 10(UP).


d.

Check that the motor gear rotates smoothly as follows.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2 (B)
Battery negative (-) → (-): 1(GND) (3 sec. or more) → 1(GND) and 10(UP) (within 1 sec.) → 1(GND) (within 1 sec.) → 1(GND) and 10(UP)
Motor gear rotates clockwise
Battery positive (+) → 2 (B)
Battery negative (-): 1(GND) (3 sec. or more) → 1(GND) and 7(DOWN) (within 1 sec.) → 1(GND) (within 1 sec.) → 1(GND) and 7(DOWN)
Motor gear rotates counterclockwise



e.

Reinstall the front power window regulator motor assembly LH.



OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH