Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM27L0U _59 Vehicle Exterior _049347 WINDOW / GLASS _0235939 POWER WINDOW CONTROL SYSTEM C

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  B2312  Power Window Switch Malfunction  


DESCRIPTION

The power window regulator motor consists of the motor, regulator and ECU. The power window regulator motor is driven by operating the power window switch. This DTC is output when the ECU built into the regulator motor determines that the power window switch is stuck.

NOTICE:
·

When the power window regulator motor is reinstalled or replaced, the power window control system must be initialized.

·

After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the AUTO UP function is used. In such cases, the AUTO UP function can be resumed by repeating the following operation at least 5 times:

(a) Close the power window by fully pulling up the power window switch and holding it in the AUTO UP position.

(b) Open the power window by fully pushing down the power window switch.



Power Window Regulator Master Switch
DTC Code DTC Detection Condition Trouble Area
B2312
·

The power window regulator master switch is stuck.

·

The power window regulator master switch is held in the same position for more than 20 seconds.


·

Power window regulator master switch

·

Harness or connector

·

Power window regulator master switch held in same position for more than 20 seconds.



Front Power Window Regulator Motor LH
DTC Code DTC Detection Condition Trouble Area
B2312
·

The power window regulator master switch stuck.

·

The Power window regulator master switch is held in the same position for more than 20 seconds.


·

Power window regulator master switch

·

Power window regulator motor

·

Harness or connector

·

Power window regulator master switch held in same position for more than 20 seconds.



Front Power Window Regulator Motor RH
DTC Code DTC Detection Condition Trouble Area
B2312
·

The power window regulator switch is stuck.

·

Power window regulator switch is held in the same position for more than 20 seconds.


·

Power window regulator switch

·

Power window regulator motor

·

Harness or connector

·

Power window regulator switch held in same position for more than 20 seconds.



WIRING DIAGRAM

B178355E04
0.348,0.033 1.528,0.255 1.179,0.223 12 for Driver Side: 0.57,0.721 1.935,0.898 1.366,0.178 10 from Main Body ECU 3.043,0.599 3.169,0.757 0.126,0.158 10 6 4.329,0.599 4.450,0.760 0.121,0.161 10 7 3.233,0.745 3.548,0.903 0.315,0.159 10 LIN1 3.902,0.745 4.237,0.901 0.336,0.156 10 LIN2 3.043,1.326 3.163,1.503 0.120,0.177 10 1 3.267,1.462 3.412,1.607 0.145,0.145 10 E 3.942,1.074 4.179,1.228 0.237,0.153 10 UP 3.725,1.536 4.195,1.692 0.470,0.156 10 DOWN 4.329,0.981 4.436,1.142 0.107,0.160 10 4 4.329,1.427 4.438,1.569 0.109,0.142 10 5 2.895,2.163 4.515,2.507 1.620,0.345 10 Power Window Regulator Master Switch Assembly 5.362,0.607 5.470,0.773 0.108,0.166 10 9 5.541,0.744 5.778,0.900 0.237,0.156 10 LIN 5.283,0.975 5.470,1.150 0.186,0.175 10 10 5.566,1.087 5.803,1.241 0.237,0.153 10 UP 5.566,1.549 6.037,1.705 0.470,0.156 10 DOWN 5.366,1.426 5.470,1.579 0.104,0.153 10 7 5.336,3.107 5.450,3.264 0.115,0.157 10 1 5.573,3.227 5.918,3.388 0.345,0.161 10 GND 4.976,3.975 6.968,4.322 1.991,0.347 10 Front Power Window Regulator Motor Assembly LH 0.776,8.591 2.403,8.764 1.627,0.172 10 : LIN Communication Line 2.906,2.007 3.136,2.184 0.230,0.177 10 M2 4.976,3.79 5.221,3.956 0.244,0.166 10 M3 0.282,4.644 2.794,4.866 2.512,0.223 12 for Front Passenger Side: 2.462,5.117 3.828,5.294 1.366,0.178 10 from Main Body ECU 4.36,6.444 4.486,6.602 0.126,0.158 10 6 4.359,6.875 4.480,7.036 0.121,0.161 10 7 3.062,7.459 3.182,7.637 0.120,0.177 10 1 3.287,7.596 3.638,7.741 0.351,0.145 10 GND 3.992,6.569 4.229,6.723 0.237,0.153 10 UP 3.744,6.991 4.215,7.147 0.470,0.156 10 DOWN 5.378,7.353 5.485,7.514 0.107,0.160 10 4 4.349,7.353 4.458,7.495 0.109,0.142 10 8 2.667,7.931 4.673,8.276 2.007,0.345 10 Front Power Window Regulator Switch Assembly RH 5.382,4.989 5.490,5.155 0.108,0.166 10 9 5.561,5.126 5.798,5.282 0.237,0.156 10 LIN 5.303,6.425 5.489,6.600 0.186,0.175 10 10 5.586,6.537 5.823,6.691 0.237,0.153 10 UP 5.586,7.018 6.056,7.174 0.470,0.156 10 DOWN 5.386,6.895 5.490,7.048 0.104,0.153 10 7 5.355,5.709 5.470,5.866 0.115,0.157 10 1 5.593,5.829 5.938,5.990 0.345,0.161 10 GND 4.996,7.928 6.987,8.276 1.991,0.347 10 Front Power Window Regulator Motor Assembly RH 2.677,7.776 2.908,7.953 0.230,0.177 10 L2 4.996,7.743 5.240,7.909 0.244,0.166 10 L3 5.591,7.464 6.000,7.621 0.409,0.158 10 AUTO 3.827,7.45 4.236,7.607 0.409,0.158 10 AUTO

PROCEDURE

1.CHECK LIN COMMUNICATION SYSTEM
a.

Check for LIN communication system DTCs related to the power window control system (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

OK:

LIN communication system DTCs are not output.




OK

2.CHECK DTC

NG

2.CHECK DTC
a.

Check where DTC B2312 is output from.

Result
Result Proceed to
B2312 output from power window regulator master switch. A
B2312 output from front power window regulator motor LH. B
B2312 output from front power window regulator motor RH. C



A

3.READ VALUE USING TECHSTREAM (POWER WINDOW REGULATOR MASTER SWITCH)

B

4.READ VALUE USING TECHSTREAM (FRONT POWER WINDOW REGULATOR MOTOR LH)

C

6.READ VALUE USING TECHSTREAM (FRONT POWER WINDOW REGULATOR MOTOR RH)
3.READ VALUE USING TECHSTREAM (POWER WINDOW REGULATOR MASTER SWITCH)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Master Switch / Data List /


e.

According to the display on the Techstream, read the Data List.

Master Switch
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door P/W Auto SW Driver side power window auto UP/DOWN switch signal / ON or OFF ON: Driver side power window auto UP/DOWN switch on power window regulator master switch operated
OFF: Driver side power window switch on power window regulator master switch not operated
-
P Door P/W Auto SW Front passenger side power window remote auto UP/DOWN switch signal / ON or OFF ON: Front passenger side power window remote auto UP/DOWN switch on power window regulator master switch operated
OFF: Front passenger side power window switch on power window regulator master switch not operated
-
P Door P/W Up SW Front passenger side power window remote manual UP switch signal / ON or OFF ON: Front passenger side power window remote manual UP switch on power window regulator master switch operated
OFF: Front passenger side power window switch on power window regulator master switch not operated
-
P Door P/W Down SW Front passenger side power window remote manual DOWN switch signal / ON or OFF ON: Front passenger side power window remote manual DOWN switch on power window regulator master switch operated
OFF: Front passenger side power window switch on the power window regulator master switch not operated
-
Window Lock Switch Status Power window LOCK switch / ON or OFF ON: Power window lock switch LOCK position
OFF: Power window lock switch UNLOCK position
-

OK:

The Techstream display changes normally when master switch is operated.




OK

END (DUE TO KEEPING SWITCH OPERATED FOR 20 SECONDS OR MORE)

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

4.READ VALUE USING TECHSTREAM (FRONT POWER WINDOW REGULATOR MOTOR LH)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / D-Door Motor / Data List /


e.

According to the display on the Techstream, read the Data List.

D-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door P/W Auto SW Driver side power window auto UP/DOWN switch signal / ON or OFF ON: Driver side power window auto UP/DOWN switch operated
OFF: Driver side power window switch not operated
-
D Door P/W Up SW Driver side power window MANUAL UP switch signal / ON or OFF ON: Driver side power window manual UP switch operated
OFF: Driver side power window switch not operated
-
D Door P/W Down SW Driver side power window MANUAL DOWN switch signal / ON or OFF ON: Driver side power window manual DOWN switch operated
OFF: Driver side power window switch not operated
-

OK:

The Techstream display changes normally when master switch is operated.




OK

END (DUE TO KEEPING SWITCH OPERATED FOR 20 SECONDS OR MORE)

NG

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - BODY GROUND)
5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - BODY GROUND)
a.
U153209E02
1.521,2.052 1.375,2.75 true 1.719,2.063 1.917,2.75 true 0.375,0.042 2.635,0.573 2.26,0.531 10 false Front view of wire harness connector: (to Power Window Regulator Master Switch Assembly) 1.25,2.771 1.479,2.927 0.229,0.156 10 false UP 1.75,2.792 2.229,2.948 0.479,0.156 10 false DOWN 0.26,1.771 0.49,1.917 0.229,0.146 10 false M2

Disconnect the M2 power window regulator master switch connector.


b.

Disconnect the M3 power window regulator motor assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M2-4 (UP) - Body ground Always 10 kΩ or higher
M2-5 (DOWN) - Body ground Always 10 kΩ or higher



d.

Reconnect the power window regulator motor assembly LH connector.


e.

Reconnect the power window regulator master switch assembly connector.



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.READ VALUE USING TECHSTREAM (FRONT POWER WINDOW REGULATOR MOTOR RH)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / P-Door Motor / Data List /


e.

According to the display on the Techstream, read the Data List.

P-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
P Door P/W Auto SW Front passenger side power window auto UP/DOWN switch signal / ON or OFF ON: Front passenger side power window auto UP/DOWN switch operated
OFF: Front passenger side power window regulator switch not operated
-
P Door P/W Up SW Front passenger side power window manual UP switch signal / ON or OFF ON: Front passenger side power window manual UP switch operated
OFF: Front passenger side power window regulator switch not operated
-
P Door P/W Down SW Front passenger side power window manual DOWN switch signal / ON or OFF ON: Front passenger side power window manual DOWN switch operated
OFF: Front passenger side power window regulator switch not operated
-

OK:

The Techstream display changes normally when master switch is operated.




OK

END (DUE TO KEEPING SWITCH OPERATED FOR 20 SECONDS OR MORE)

NG

7.INSPECT FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY RH
7.INSPECT FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY RH
a.
B184772E18
1.417,2.521 1.604,2.094 true 0.76,2.458 1.396,2.083 true 1.875,2.083 2.104,2.469 true 2.083,1.875 2.479,2.01 true 0.115,0.063 2.625,0.563 2.51,0.5 10 false Component without harness connected: (Front Power Window Regulator Switch Assembly RH) 2.125,2.531 2.333,2.719 0.208,0.188 10 false UP 2.521,1.958 2.896,2.156 0.375,0.198 10 false GND 0.323,2.406 0.74,2.604 0.417,0.198 10 false AUTO 1.188,2.563 1.677,2.76 0.49,0.198 10 false DOWN

Remove the front power window regulator switch assembly RH (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (UP) - 1 (GND) Manual UP operation Below 1 Ω
7 (DOWN) - 1 (GND) Manual DOWN operation Below 1 Ω
8 (AUTO) - 1 (GND) AUTO UP/DOWN operation Below 1 Ω
6 (UP) - 1 (GND) Not operated 10 kΩ or higher
7 (DOWN) - 1 (GND) Not operated 10 kΩ or higher
8 (AUTO) - 1 (GND) Not operated 10 kΩ or higher



c.

Reinstall the power window regulator switch assembly RH.



OK

8.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR SWITCH RH - BODY GROUND)

NG

REPLACE FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY RH

8.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR SWITCH RH - BODY GROUND)
a.
U153211E02
0.906,2.51 1.604,2.375 true 2.344,1.917 1.781,2.292 true 1.958,2.375 2.323,2.458 true 0.229,0.104 2.594,0.604 2.365,0.5 10 false Front view of wire harness connector: (to Front Power Window Regulator Switch Assembly RH) 0.646,2.438 0.854,2.594 0.208,0.156 10 false UP 2.396,1.833 2.865,1.979 0.469,0.146 10 false DOWN 2.375,2.375 2.781,2.521 0.406,0.146 10 false AUTO 0.615,1.854 0.802,2.01 0.188,0.156 10 false L2

Disconnect the L2 power window regulator switch assembly RH connector.


b.

Disconnect the L3 power window regulator motor assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L2-6 (UP) - Body ground Always 10 kΩ or higher
L2-7 (DOWN) - Body ground Always 10 kΩ or higher
L2-8 (AUTO) - Body ground Always 10 kΩ or higher



d.

Reconnect the power window regulator motor assembly RH connector.


e.

Reconnect the power window regulator switch assembly RH connector.



OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR