Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM27L0U _59 Vehicle Exterior _049347 WINDOW / GLASS _0235939 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch  


DESCRIPTION

If the manual UP/DOWN function does not operate, there may be a malfunction in the power window regulator switch, the front power window regulator motor RH, the harness and connector.


WIRING DIAGRAM

B184409E06
2.385,0.776 3.733,0.956 1.349,0.180 10 from Main Body ECU 5.491,2.666 6.041,2.836 0.549,0.170 10 DOWN 3.667,2.666 4.129,2.836 0.461,0.170 10 DOWN 4.255,2.583 4.449,2.739 0.194,0.156 10 7 5.225,3.056 5.357,3.208 0.132,0.152 10 4 5.225,2.579 5.357,2.732 0.132,0.152 10 7 5.491,3.139 5.897,3.308 0.406,0.170 10 AUTO 5.491,2.225 5.772,2.395 0.281,0.170 10 UP 5.491,1.101 5.648,1.271 0.156,0.170 10 B 5.491,1.514 5.869,1.684 0.378,0.170 10 GND 0.67,4.264 2.639,4.434 1.969,0.170 10 : LIN Communication Line 3.187,3.272 3.530,3.442 0.343,0.170 10 GND 3.715,3.139 4.135,3.309 0.420,0.170 10 AUTO 3.921,2.225 4.143,2.395 0.222,0.170 10 UP 4.255,2.134 4.463,2.287 0.208,0.152 10 6 5.265,1.007 5.386,1.159 0.121,0.152 10 2 5.265,1.404 5.386,1.556 0.121,0.152 10 1 5.186,2.119 5.394,2.271 0.208,0.152 10 10 2.594,3.684 4.631,4.051 2.037,0.368 10 Front Power Window Regulator Switch Assembly RH 4.965,3.836 6.917,4.178 1.952,0.342 10 Front Power Window Regulator Motor Assembly RH 2.957,3.195 3.066,3.351 0.109,0.156 10 1 2.657,3.512 2.887,3.668 0.230,0.156 10 L2 4.965,3.656 5.222,3.812 0.257,0.156 10 L3 4.255,3.056 4.450,3.212 0.194,0.156 10 8 0.871,1.082 1.657,1.397 0.787,0.316 10 from Battery 1.778,1.247 2.780,1.406 1.002,0.158 10 POWER NO. 4 5.255,0.643 5.365,0.810 0.110,0.168 10 9 5.491,0.79 5.749,0.938 0.257,0.147 10 LIN

PROCEDURE

1.CHECK LIN COMMUNICATION SYSTEM
a.

Check for LIN communication system DTCs related to the power window control system (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

LIN communication system DTCs are not output.




OK

2.CHECK DTC (B2312)

NG

2.CHECK DTC (B2312)
a.

Check if DTC B2312 is output (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2312 is not output.




OK

3.READ VALUE USING TECHSTREAM (P-DOOR MOTOR)

NG

3.READ VALUE USING TECHSTREAM (P-DOOR MOTOR)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / P-Door Motor / Data List.


e.

According to the display on the Techstream, read the Data List.

P-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
P Door P/W Up SW Front passenger side power window manual UP switch signal / ON or OFF ON: Front passenger side power window manual UP switch operated
OFF: Front passenger side power window switch not operated
-
P Door P/W Down SW Front passenger side power window manual DOWN switch signal / ON or OFF ON: Front passenger side power window manual DOWN switch operated
OFF: Front passenger side power window switch not operated
-

OK:

The Techstream display changes normally when front passenger side power window switch is operated.




OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

4.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR SWITCH RH - BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR SWITCH RH - BODY GROUND)
a.
U153214E01
0.178,0.128 2.618,0.866 2.441,0.739 10 Front view of wire harness connector: (to Front Power Window Regulator Switch Assembly RH) 0.864,1.704 1.121,1.863 0.256,0.159 10 L2 0.819,2.471 1.153,2.623 0.333,0.152 10 GND 1.149,2.471 1.491,2.151 false

Disconnect the L2 Front power window regulator switch assembly RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L2-1 (GND) - Body ground Always Below 1 Ω



c.

Reconnect the Front power window regulator switch assembly connector.



OK

5.CHECK HARNESS AND CONNECTOR (FRONT P/W REGULATOR MOTOR RH - BATTERY, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (FRONT P/W REGULATOR MOTOR RH - BATTERY, BODY GROUND)
a.
U153213E02
1.521,1.823 1.01,2.042 true 1.885,1.813 2.458,2.063 true 0.167,0.021 2.417,0.563 2.25,0.542 10 false Front view of wire harness connector: (to Front Power Window Regulator Motor Assembly RH) 0.74,1.292 0.948,1.448 0.208,0.156 10 false L3 2.49,2.052 2.667,2.24 0.177,0.188 10 false B 0.76,2.042 1.115,2.229 0.354,0.188 10 false GND

Disconnect the L3 front power window regulator motor assembly RH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L3-2 (B) - Body ground Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
L3-1 (GND) - Body ground Always Below 1 Ω



c.

Reconnect the front power window regulator motor assembly RH connector.



OK

6.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW SWITCH RH - FRONT POWER WINDOW MOTOR RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW SWITCH RH - FRONT POWER WINDOW MOTOR RH)
a.
U153215E02
1.198,1.552 1.615,1.781 true 1.813,1.74 2.281,1.354 true 1.979,1.76 2.375,1.573 true 1.208,3.667 1.583,3.865 true 1.896,4 2.26,3.823 true 1.219,4.229 1.469,4.042 true 0.167,2.031 2.438,2.583 2.271,0.552 10 false Front view of wire harness connector: (to Front Power Window Regulator Motor Assembly RH) 0.156,0.063 2.417,0.594 2.26,0.531 10 false Front view of wire harness connector: (to Front Power Window Regulator Switch Assembly RH) 0.635,1.104 0.823,1.271 0.188,0.167 10 false L2 0.667,3.24 0.896,3.427 0.229,0.188 10 false L3 0.938,1.448 1.219,1.615 0.281,0.167 10 false UP 2.302,1.229 2.781,1.417 0.479,0.188 10 false DOWN 2.427,1.51 2.844,1.677 0.417,0.167 10 false AUTO 2.313,3.76 2.594,3.927 0.281,0.167 10 false UP 0.708,4.156 1.188,4.344 0.479,0.188 10 false DOWN 0.75,3.573 1.167,3.74 0.417,0.167 10 false AUTO

Disconnect the L2 front power window regulator switch assembly RH connector.


b.

Disconnect the L3 front power window regulator motor assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L2-6 (UP) - L3-10 (UP) Always Below 1 Ω
L2-7 (DOWN) - L3-7 (DOWN) Always Below 1 Ω
L2-8 (AUTO) - L3-4 (AUTO) Always Below 1 Ω
L2-6 (UP) - Body ground Always 10 kΩ or higher
L2-7 (DOWN) - Body ground Always 10 kΩ or higher
L2-8 (AUTO) - Body ground Always 10 kΩ or higher



d.

Reconnect the front power window regulator motor assembly RH connector.


e.

Reconnect the front power window regulator switch assembly RH connector.



OK

7.INSPECT FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY RH
a.
B184772E19
1.438,2.448 1.615,2.094 true 1.885,2.073 2.135,2.427 true 2.083,1.854 2.5,1.948 true 0.115,0.042 2.625,0.542 2.51,0.5 10 false Component without harness connected: (Front Power Window Regulator Switch Assembly RH) 2.094,2.479 2.469,2.677 0.375,0.198 10 false UP 2.521,1.875 2.896,2.073 0.375,0.198 10 false GND 1.125,2.458 1.615,2.656 0.49,0.198 10 false DOWN

Remove the front power window regulator switch assembly RH (See page Vehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (UP) - 1 (GND) Manual UP operation Below 1 Ω
7 (DOWN) - 1 (GND) Manual DOWN operation Below 1 Ω



c.

Reinstall the front power window regulator switch assembly RH.



OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPLACE FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY RH