Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR CLOSER SYSTEM
RM27L0U _59 Vehicle Exterior _049349 DOOR / HATCH _0235967 BACK DOOR CLOSER SYSTEM C

DOOR / HATCH  BACK DOOR CLOSER SYSTEM  B2251  Back Door Closer Switch Malfunction  


DESCRIPTION

The power back door drive unit (power back door ECU) inputs signals from the full-latch switch, sector switch and back door courtesy light switch, which are built into the back door lock. Based on these switch signals, the latch position of the back door lock is determined.

DTC No. DTC Detection Condition Trouble Area
B2251 While back door closer is operating, malfunction is detected in position information from each switch within specified amount of time.
·

Back door lock

·

Wire harness

·

Power back door ECU



WIRING DIAGRAM

B443234E02
1.344,0.646 2.313,0.844 0.969,0.198 10 false Sector Switch 1.292,1.479 2.26,1.677 0.969,0.198 10 false Latch Switch 1.281,2.271 2.583,2.594 1.302,0.323 10 false Back Door Courtesy Light Switch 0.667,1.948 0.875,2.135 0.208,0.188 10 false E 0.458,1.948 0.667,2.135 0.208,0.188 10 false 3 2.344,0.344 2.792,0.552 0.448,0.208 10 false FSW 2.344,1.156 2.792,1.365 0.448,0.208 10 false CLS 2.542,1.979 2.75,2.177 0.208,0.198 10 false S 2.771,0.365 2.979,0.563 0.208,0.198 10 false 4 2.781,1.188 2.99,1.385 0.208,0.198 10 false 5 2.792,1.969 3,2.167 0.208,0.198 10 false 6 5.604,0.344 5.896,0.542 0.292,0.198 10 false 24 5.573,1.177 5.865,1.375 0.292,0.198 10 false 22 5.573,2.219 5.865,2.448 0.292,0.229 10 false 20 5.875,0.469 6.323,0.677 0.448,0.208 10 false POS 5.865,2.375 6.313,2.583 0.448,0.208 10 false FUL 5.854,1.26 6.302,1.469 0.448,0.208 10 false HAF 5.417,2.917 5.875,3.104 0.458,0.188 10 false O30 5.417,3.083 7.146,3.438 1.729,0.354 10 false Power Back Door Drive Unit (Power Back Door ECU) 4.875,2.365 5.167,2.594 0.292,0.229 10 false V2 3.521,2.094 3.813,2.323 0.292,0.229 10 false V3 3.521,3.469 3.813,3.698 0.292,0.229 10 false V3 3.521,3.823 3.813,4.052 0.292,0.229 10 false V2 3.521,1.896 3.813,2.125 0.292,0.229 10 false 10 3.531,3.25 3.823,3.479 0.292,0.229 10 false 20 3.542,3.656 3.833,3.885 0.292,0.229 10 false 6 4.875,2.177 5.167,2.406 0.292,0.229 10 false 17 3.813,2.094 4.26,2.302 0.448,0.208 10 false BDCY 3.813,3.469 4.26,3.677 0.448,0.208 10 false CTYE 3.813,3.833 4.26,4.042 0.448,0.208 10 false GND 4.375,2.385 4.823,2.594 0.448,0.208 10 false OCTY 3.792,4.333 4.906,4.51 1.115,0.177 10 false Back Door ECU

PROCEDURE

1.READ VALUE USING TECHSTREAM (HALF LATCH SW)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Back Door / Data List /


e.

According to the display on the Techstream, read the Data List.

Back Door (Power Back Door ECU)
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Half Latch SW Latch switch signal / ON or OFF ON: Back door lock motor is open-latch or over-latch
OFF: Back door lock motor is full-latch or half-latch
-

OK:

The display is as specified in the normal condition.




OK

2.READ VALUE USING TECHSTREAM (BACK DOOR COURTESY LIGHT SWITCH)

NG

10.INSPECT BACK DOOR LOCK (LATCH SWITCH)
2.READ VALUE USING TECHSTREAM (BACK DOOR COURTESY LIGHT SWITCH)
a.

Connect the Techstream to the DLC3.


b.

Turn the engine switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Back Door / Data List /


e.

According to the display on the Techstream, read the Data List.

Back Door (Power Back Door ECU)
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Courtesy SW Back door courtesy light switch signal / ON or OFF ON: Back door is open
OFF: Back door is closed
-

OK:

The display is as specified in the normal condition.




OK

REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)

NG

3.CHECK HARNESS AND CONNECTOR (BACK DOOR ECU - POWER BACK DOOR ECU)
3.CHECK HARNESS AND CONNECTOR (BACK DOOR ECU - POWER BACK DOOR ECU)
a.

Disconnect the V2 back door ECU connector.


U153292E02
2.615,1.271 2.49,1.271 2.49,1.271 1.25,2.052 true 2.833,3.5 2.667,3.5 2.667,3.5 1.938,4.26 true 0.302,0.125 2.625,0.458 2.323,0.333 10 false Front view of wire harness connector: (to Back Door ECU) 0.365,2.583 2.688,2.938 2.323,0.354 10 false Front view of wire harness connector: (to Power Back Door ECU) 0.625,1.729 0.823,1.885 0.198,0.156 10 false V2 0.156,4.104 0.438,4.271 0.281,0.167 10 false O30 2.667,1.198 3.083,1.344 0.417,0.146 10 false OCTY 2.875,3.427 3.208,3.594 0.333,0.167 10 false FUL

b.

Disconnect the O30 power back door ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V2-17 (OCTY) - O30-20 (FUL) Always Below 1 Ω
V2-17 (OCTY) or O30-20 (FUL) - Body ground Always 10 kΩ or higher



d.

Reconnect the back door ECU connector.


e.

Reconnect the power back door ECU connector.



OK

4.READ VALUE USING BACK DOOR ECU (BACK DOOR COURTESY LIGHT SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING BACK DOOR ECU (BACK DOOR COURTESY LIGHT SWITCH)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Back Door P/W / Data List /


e.

According to the display on the Techstream, read the Data List.

Back Door P/W (Back Door ECU)
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Back Door Courtesy SW Back door courtesy light switch signal / ON or OFF ON: Back door is open
OFF: Back door is closed
-

OK:

The display is as specified in the normal condition.




OK

REPLACE BACK DOOR ECU

NG

5.INSPECT BACK DOOR LOCK (BACK DOOR COURTESY LIGHT SWITCH)
5.INSPECT BACK DOOR LOCK (BACK DOOR COURTESY LIGHT SWITCH)
B191744E10
6.813,1.917 6.708,1.917 6.708,1.917 6.542,1.5 true 6.021,1.885 6.167,1.885 6.167,1.885 6.385,1.302 true 6.854,1.833 6.979,1.99 0.125,0.156 10 false S 5.875,1.802 5.99,1.948 0.115,0.146 10 false E 4.76,1.26 5.115,1.563 0.354,0.302 10 true Close 3.729,1.229 4.26,1.521 0.531,0.292 10 true Release 2.26,0.781 2.927,0.927 0.667,0.146 10 false Over-latch 2.188,1.094 2.781,1.25 0.594,0.156 10 false Full-latch 1.99,1.833 2.615,1.979 0.625,0.146 10 false Half-latch 1.708,2.271 2.438,2.438 0.729,0.167 10 false Open-latch

a.

Remove the back door lock (See page Vehicle Interior>DOOR LOCK>BACK DOOR LOCK>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Door Lock Latch Position Specified Condition
6 (S) - 3 (E) Open-latch Below 1 Ω
6 (S) - 3 (E) Half-latch Below 1 Ω
6 (S) - 3 (E) Full-latch 10 kΩ or higher
6 (S) - 3 (E) Over-latch 10 kΩ or higher




OK

6.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK - BACK DOOR ECU AND BODY GROUND)

NG

REPLACE BACK DOOR LOCK

6.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK - BACK DOOR ECU AND BODY GROUND)
a.

Disconnect the V5 door lock connector.

B443242E01
0.146,1.573 0.573,1.844 0.427,0.271 2.177,1.583 2.604,1.854 0.427,0.271 4.74,1.594 5.167,1.865 0.427,0.271 1.167,1.75 1.448,1.438 1.448,1.438 1.594,1.438 true 1,1.938 0.802,2.229 0.802,2.229 0.667,2.229 true 3.75,1.573 4.031,1.26 4.031,1.26 4.177,1.26 true 5.74,1.865 6.396,1.083 6.396,1.083 6.542,1.083 true 5.625,2.042 5.406,2.396 5.406,2.396 5.24,2.396 true 0.042,0.104 2.302,0.49 2.26,0.385 10 false Front view of wire harness connector: (to Back Door Lock) 2.469,0.104 4.771,0.469 2.302,0.365 10 false Front view of wire harness connector: (to Back Door ECU) 4.885,0.083 7.156,0.427 2.271,0.344 10 false Front view of wire harness connector: (to Back Door ECU) 0.271,1.625 0.542,1.802 0.271,0.177 10 false V5 2.323,1.635 2.594,1.813 0.271,0.177 10 false V2 4.865,1.656 5.135,1.833 0.271,0.177 10 false V3 0.542,2.135 0.813,2.313 0.271,0.177 10 false S 1.635,1.354 1.906,1.531 0.271,0.177 10 false E 4.229,1.198 4.719,1.406 0.49,0.208 10 false GND 6.573,1 7.063,1.177 0.49,0.177 10 false BDCY 4.844,2.302 5.333,2.479 0.49,0.177 10 false CTYE


b.

Disconnect the V2 and V3 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V5-6 (S) - V3-10 (BDCY) Always Below 1 Ω
V5-3 (E) - V3-20 (CTYE) Always Below 1 Ω
V2-6 (GND) - Body ground Always Below 1 Ω
V5-6 (S) or V3-10 (BDCY) - Body ground Always 10 kΩ or higher



d.

Reconnect the door lock and ECU connector.



OK

7.REPLACE POWER BACK DOOR DRIVE UNIT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE POWER BACK DOOR DRIVE UNIT
a.

Temporarily replace the power back door drive unit with a new or normally functioning one (See page Vehicle Interior>DOOR LOCK>BACK DOOR LOCK>REMOVAL).



NEXT

8.CLEAR DTC
8.CLEAR DTC

NEXT

9.CHECK DTC OUTPUT
9.CHECK DTC OUTPUT
a.

Check the DTCs (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER SYSTEM>DTC CHECK / CLEAR).

OK:

DTC not output B2251.




OK

END (POWER BACK DOOR DRIVE UNIT DEFECTIVE)

NG

REPLACE BACK DOOR ECU

10.INSPECT BACK DOOR LOCK (LATCH SWITCH)
B191744E11
6.698,1.99 6.594,1.99 6.594,1.99 6.406,1.5 true 5.885,1.885 5.979,1.885 5.979,1.885 6.375,1.271 true 6.74,1.906 7.042,2.063 0.302,0.156 10 false CLS 5.76,1.823 5.885,1.969 0.125,0.146 10 false E 4.76,1.281 5.188,1.583 0.427,0.302 10 true Close 3.656,1.229 4.208,1.563 0.552,0.333 10 true Release 2.26,0.781 2.927,0.927 0.667,0.146 10 false Over-latch 2.188,1.094 2.781,1.25 0.594,0.156 10 false Full-latch 1.99,1.833 2.615,1.979 0.625,0.146 10 false Half-latch 1.708,2.271 2.438,2.438 0.729,0.167 10 false Open-latch

a.

Remove the back door lock (See page Vehicle Interior>DOOR LOCK>BACK DOOR LOCK>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Latch Switch

Tester Connection Door Lock Latch Position Specified Condition
5 (CLS) - 3 (E) Open-latch Below 1 Ω
5 (CLS) - 3 (E) Half-latch 10 kΩ or higher
5 (CLS) - 3 (E) Full-latch 10 kΩ or higher
5 (CLS) - 3 (E) Over-latch Below 1 Ω




OK

11.CHECK HARNESS AND CONNECTOR

NG

REPLACE BACK DOOR LOCK

11.CHECK HARNESS AND CONNECTOR
a.

Disconnect the V5 door lock connector.

B443244E01
0.781,1.135 1.198,1.365 0.417,0.229 3.677,1.083 4.094,1.313 0.417,0.229 0.76,2.906 1.177,3.135 0.417,0.229 3.729,2.854 4.146,3.083 0.417,0.229 1.844,1.333 2.125,1.042 2.125,1.042 2.292,1.042 true 1.833,1.49 2.094,1.646 2.094,1.646 2.281,1.646 true 5.438,1.427 5.635,1.75 5.635,1.75 5.823,1.75 true 2.167,2.927 2.448,2.76 2.448,2.76 2.635,2.76 true 4.573,3.563 4.74,3.563 4.74,3.563 4.99,3.313 true 0.594,0.063 2.885,0.406 2.292,0.344 10 false Front view of wire harness connector: (to Back Door Lock) 4.208,0.063 6.448,0.417 2.24,0.354 10 false Front view of wire harness connector: (to Power Back Door ECU) 0.76,1.958 3.042,2.302 2.281,0.344 10 false Front view of wire harness connector: (to Back Door ECU) 4.271,1.917 6.552,2.26 2.281,0.344 10 false Front view of wire harness connector: (to Back Door ECU) 0.906,1.188 1.156,1.354 0.25,0.167 10 false V5 2.354,0.948 2.865,1.125 0.51,0.177 10 false E 2.375,1.552 2.823,1.771 0.448,0.219 10 false CLS 5.854,1.667 6.302,1.885 0.448,0.219 10 false HAF 3.74,1.125 4.198,1.344 0.458,0.219 10 false O30 0.896,2.948 1.146,3.115 0.25,0.167 10 false V2 2.698,2.688 3.146,2.906 0.448,0.219 10 false GND 3.844,2.906 4.094,3.073 0.25,0.167 10 false V3 4.156,3.479 4.604,3.698 0.448,0.219 10 false CTYE


b.

Disconnect the O30, V2 and V3 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V5-3 (E) - V3-20 (CTYE) Always Below 1 Ω
V5-5 (CLS) - O30-22 (HAF) Always Below 1 Ω
V2-6 (GND) - Body ground Always Below 1 Ω
V5-5 (CLS) or O30-22 (HAF) - Body ground Always 10 kΩ or higher



d.

Reconnect the door lock and ECU connector.



OK

REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR